Having problems with your Hoover U5753-900 WindTunnel Bagless Upright Vacuum ?
My hoover u5725-960 wind tunnel brush won't rotate
It sounds like you need to replace the belt
Repair Help & Product Troubleshooting for Hoover U5753-900 WindTunnel Bagless Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
My hoover u5725-960 wind tunnel brush won't rotate
It sounds like you need to replace the belt ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum
Why wont the self propelled brush on the hoover wind tunnel work. large belt is ok. the small belt looks 0k.
No don't do that,have a little patience.check where the self propelled assembly is and see if anything got in there,something might be loose and the teeth are meeting each other.thats a good vavuum.i have 2 but their not self propelled.try taking the ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Hi. I have a Hoover Wind Tunnel Deluxe vacuum, and the rotating brush does not spin any longer, but still has air suction. Cause ? Sincereley, Teresa T. [email protected]
Could use the model number. Most use a belt, if yours does, then you may need to relace the belt, also check the brush roll. ... Vacuums
I have a hoover all terrain cleaning for carpets and hard floors and the Brushes will not rotate. I have replaced the filter on the bottom which is recommended by hoover and the brushes still wont rotate. Please advise
I assume this unit has no mechanism to turn the brush but instead using the air flow to activate the brush, in this instance it could be that there is dirt which is caught up in the brush which is stopping the rotation.A nice good clean and make sure ... Hoover Vacuums
Hoover, model # UH30070 Wind tunnel vacuum Brush won't turn. I do not see how to remove this to replace the brush, and besides it's only about a year old! Why is it already broken? There's no visible evidence on the brush that would make it stop, i.e. string, clogged, etc. Can you help?
... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Hoover Wind Tunnel 7500 Brush not Turning. I have replaced the Brush and the belt. The problem does not seem to be either to me. I believe might be a missing part. The place were the belt hooks on is a metal pole which never seems to grip the belt well. In fact it seems loose most of the time and slips on the brush, causing the belt to eventually burn up. Could there be a missing plastic or rubber piece meant to hold the belt taught on the metal pole?
Check the Idler Pulley part Number 43241004 (Item 13 in the IPB)http://184.108.40.206/v/u6451900.pdf ... Vacuums
Folks, My wife and I own a three-year-old Hoover U6434-900 self-propelled "Wind Tunnel" upright vacuum cleaner. The problem is that, even on the highest setting (front-end as high as possible), it gets bogged-down in even shallow pile carpet to the point that the brush stops. I've cleaned the machine thoroughly, pulling hair, thread, dental floss and such from the brush (and everywhere else), including unscrewing the brush end caps and pulling out the cat hair mats which formed in there.
Check to see if the V belt sits too deep in the brushroll groove, if it sits too deep you will need to replace the brushroll. the top of the belt should be about flush with the brushroll. also you have to take the screws out of the self propelled uni ... Vacuums
Hoover wind tunnel upright self propelled. U6473-900. Brush does not work. Heard it was a 'brush controller' problem and can be fixed. Please tell me how.
Most likely the flat belt has stretched enough so as to not turn the pulley that in turn turns the brush roll using a V belt. Also there is a small idler wheel, if hook up, then it won't engage the V belt. ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
I have a Hoover Wind Tunnel Self-propelled vacuum. I changed the belts because the brush was not turning. After replacing the belts the brush is still not turning what can be wrong?
There are two belts on the wind tunnel this video will show you how to repair ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Hoover Wind Tunnel U6433-900
The problem i see the most is that people have the setting on the front of the vacuumfor "floors" not carpet, switch it over and it will start as soon as the handle is released , if not try belts and finally motor burnt out. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Hoover Wind Tunnel V-Belt no longer turns brush
That is the correct belt what you dont see is a tension pulley that when the handle is released pushes on top of that belt giving it the tension it needs. try replacing the other belt, even if it isnt broken it could easily be stretched out ( all bel ... Hoover U6311-930 Power Drive Bagged Upright Vacuum
Hoover wind tunnel cyclonic U5780900 1 year old. brush will not turn. too much slack in vbelt when in carpet position. Belt is good
Well, the V belt is normally fairly slack until the handle is dropped below 45 degrees, which is when the belt tensioner assembly drops into place. If turning the brushroll by hand when the vacuum is in this position fails to rotate the self propel p ... Hoover Vacuums
I can't get the brushes to rotate on my hoover steam vac v. i took them apart and cleaned them and they still wont work. any ideas?
Scrubbing brushes are driven by a belt. The belt either broke or slipped off its pulley. ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum
No suction i have a hoover supreme wind tunnel vac and its relatively new and the suction, well......sucks. It wont pick anything up! I am extremely frustrated! I picked up a ball of fuzz off the carpet and held it under the vacuum and it still wouldn't **** it up. I then shoved the fuzz up INTO the vacuum. It fell right back out. I may as well not even vacuum. Please help!
I have found more vacuums on the way to the dump because they were full. Check. Is it full?\015\012If not the air way is clogged. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old
Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
Hoover wind tunnel vacuum beater brush won't engage
... Hoover UH70120 WindTunnel TSeries Rewind Bagless Upright Vacuum Cleaner
I have a Hoover Wind Tunnel U6437-900. The brush will not turn. I have replaced both of the belts with no success. Any suggestions?
Hello,\015\012\015\012If you've already changed the belts and the machine still won't run, it can really be only a few things. \015\012\015\012The first thing you should check to make sure that the roller brush is good. Yo ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
I have a Hoover Wind Tunnel, model #U6655-900. I have changed both belts & have cleaned the brush. It is difficult to push and I smell burning rubber. Do you have any suggestions?
The transmission for the self-propelled could be broken. That's the reason it's difficult to push and the smell ... Vacuums
Hoover wind tunnel, brushes are not spinning. Belt seems loose but maybe that is normal.
The belt (one around the roller) will only engage the roller upon 2 conditions. the carpet switch needs to be in carpet and the machine needs to be tilted back. The other belt, may appear to be on, but can be stretched and also cause this issue, the ... Vacuums
My hoover wind tunnel self propelled vacuum wont stand up be itself. The locking thing is not working. Thank You. [email protected]
If you look at the foot pedal, see if it is locked in the base, and pivots freely. I have seen some of these that break the base, or break the spring hinge on the back side of the release pedal. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum
The scrub brushes wont rotate - Hoover Steam Vac Dual V w/ SpinScrub Vacuum
Clean it should be hair struck ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum
HI, my motorized brush barely turns.It makes a hot rubber smell. I took apart and noticed the spindle the belt turns on discolored from heat. Cleaned it, but still no turning of the brush.The vac is a hoover wind tunnel. As it moved accidentally touched the belt/ spindle and burned my hand a little. Very hot in area. Bright spark from motor noted. Was careful not to touch that part!
That means that the belt is stretched and it is slipping on the motor shaft, that is why it is hot and smells like burning rubber. You need to replace the belt. Here is the correct belt you need: ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum
I purchased a hoover wind tunnel SH40050 and am not able to get the brush to roll
Just check the belt flip the vacuum over take lid off and check belt ... Hoover Vacuums
Hoover wind tunnel self propelled brush roll not working
... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
I have a uh07400 Hoover wind tunnel and brush roller doesn't work
... Hoover Vacuums