Having problems with your Hoover U5753-900 WindTunnel Bagless Upright Vacuum ?

I need to change the small belt - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


Answers :

Just remove the cover on the bottom of the vacuum by loosening the screws holding it on. Once they are off, you'll be able to slide out the rotating brush, and you'll see the belt there. Look inside the vacuum also, as when they break, they can spring anywhere in the machine. Usually they will come out when you remove the brush. Once you have the brush out, just slide the new belt over it and replace the brush from where it came. Then return the cover you first took off. All set and ready to start cleaning again !!

If you need to buy a replacement belt, take the model number from your machine to the store or contact the manufacturer online or by phone. It should only cost you about $5. for the belt.
I have the same model number and I had no problem.
Good Luck and I hope this helps.
Repair Help & Product Troubleshooting for Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I need to change the small belt - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


Just remove the cover on the bottom of the vacuum by loosening the screws holding it on. Once they are off, you'll be able to slide out the rotating brush, and you'll see the belt there. Look inside the vacuum also, as when they break, they can sprin ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

I can't change belt - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=832643\015\012Generic problem for all Vacuums\015\012I can't change belt\015\012Posted by jaw53t on Jul ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Belt replacement for Hoover U5100-9RM - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

How do I change the belt on the motor? - Hoover U6630-900 WindTunnel Bagless Upright Vacuum


Hi. This is easily done. Flip the vacuum over, beater bar up. With the machine unplugged, locate the screws or tabs that hold the base plate on, surrounding the beater bar. Remove the plate. The beater bar is held in place by fitting into socket ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Brush won't turn, belts intact - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


Even though the belt is intact it can still be stretched and not turn the brush. You can get replacement belts here:www.vacbelts.com ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Belt works fine but there is no suction - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


This usually indicates a clog in the hose and airflow system. It's most likely to be behind the filter in the tank or in the power head area.\015\012Detach hose from power head and look inside. If you can't see anything, try dropping a penny ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Changing belts - Hoover U6616-900 WindTunnel Bagless Upright Vacuum


You can find the instructions with diagrams on pg 10 in the manual http://www.hoover.com/pdfs/manuals/U6616900.pdf ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

How to change belt on hoover savvy vacuum - Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum


How do I change the smaller brush belt on a Hoover Windtunnel Cyclonic? ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

Change belt on hoover savvy bag and bagless upright vacuum


... Hoover U8155-900 Savvy Bagged Upright Vacuum

Change belt on hoover whole house - Hoover Whole House Bagless Upright Vacuum, UH71214


... Hoover Whole House Bagless Upright Vacuum, UH71214

Hoover cord will not retract - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

How do change belt on Hoover U5163-900 - Hoover Fold Away U5162-900 Bagless Upright Vacuum


... Hoover Fold Away U5162-900 Bagless Upright Vacuum

Hoover Windtunnel Bagged upright vacuum is smoking and belt is slitting and burning


You probably need to replace your brushroll seeing that your belt is burning means motor is turning. first check you brushroll and see if there is an obstruction keeping it from spinning if its not spinning freely replace ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Our brush won,t spin can you help? - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


Most likely your brush needs to be removed and cleaned. Clean all debris that might be in the bristles of the brush. You will see a holder for the brush on each end that holds it into the frame of the vacuum. The two holders should turn f ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

How to change a hoover belt on a dyson - Dyson DC07 Full Gear Bagless Upright Cyclonic Vacuum


... Dyson DC07 Full Gear Bagless Upright Cyclonic Vacuum

Hose is clogged - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


Hi,Here is a tip that I wrote about my Bissel but I bet you have the same problemand the hose is clogged...Bissell Bagless Upright Vacuum not work ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Vac runs for about 15 mins. then stops - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


The unit is not getting the proper airflow and the motor is overheating to shut down. \012\012You should check/clean out the filter in the dirt chamber there. If the filter is more than 1 year old, you should replace the filter. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

How to install the torsion spring - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

I have a Hoover WindTunnel Bagless Vacuum Cleaner, Model #U5753-900, Serial number 110600215585, which I purchased from Loew's on 3/31/07. With it, came a Hoove Slider for hard floor surfaces, Model #S2105, Serial number 050500084989. The Slider strted making a noise--I thought something had been caught in the roller, but discovered, it had not; so I and my husband proceeded to take the Slider apart. I believe one of the belts had come off; but when we took the screws off the bottom to check


... Vacuums

How to install a U8172-900 belt - Hoover U6630-900 WindTunnel Bagless Upright Vacuum


Your savvy bagless has a geared belt. remove the bottom plate and then remove the 2 back screws near the back wheels to remove the top cover also peel off the hoover decal to access the top cover screw. this will expose all components to replace the ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Brush on underside not working, please help. - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


Turn the unit over and remove the four screws that retain the bottom plate over the agitator. Remove the bottom plate and see if the belt of off or broken. The belt part number is printed on the data label for the cleaner. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

It's not sucking up dirt - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


A couple things to check: Is there suction at the end of the hose if you unplug it from the housing. If you have vacuum to the hose, but not to the brushroll, then you may have a clog in the duct.\015\012\015\012Another check is if the ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Vaccume overheats and shuts down - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


Check your filters. Not changing or cleaning your filters suffocates your motor, so that could be the problem.I suggest checking your local yellow pages for a local vacuum shop and have them fully inspect your vacuum for any clogs. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

How to change belt in hoover core 3 upright bagless vacuum cleaner


... Vacuums

The belt needs replacing - Hoover U6630-900 WindTunnel Bagless Upright Vacuum


Here is the manual to your Hoover U6630www.thinkvacuums.com/pdf/uprights/Hoover_U6630.pdfit goes into detail on how to change the belt and which belt to purchase. Ask for a flat belt Hoover part No. 38528035 when you're going to pur ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1383 seconds