Having problems with your Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum ?
After running for a while vaccum shuts off machine gets hot even after cleaning out cannister
Check everywhere for blockages and make sure filters are clean
Repair Help & Product Troubleshooting for Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
After running for a while vaccum shuts off machine gets hot even after cleaning out cannister
Check everywhere for blockages and make sure filters are clean ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum
Vapor Clean TR 5 Under "maintenance" they told me to unscrew to empty refill tank. After doing that, no water came out and the piece that the scew went into is now in the tank. It is too large to get out and even if you put the screw back inti that piece ir still goes into the machine. Can I still use the machine? brand new only uded it once
I is really needed to check this with the manufacturer! See contact details below: ... Vacuums
Folks, My wife and I own a three-year-old Hoover U6434-900 self-propelled "Wind Tunnel" upright vacuum cleaner. The problem is that, even on the highest setting (front-end as high as possible), it gets bogged-down in even shallow pile carpet to the point that the brush stops. I've cleaned the machine thoroughly, pulling hair, thread, dental floss and such from the brush (and everywhere else), including unscrewing the brush end caps and pulling out the cat hair mats which formed in there.
Check to see if the V belt sits too deep in the brushroll groove, if it sits too deep you will need to replace the brushroll. the top of the belt should be about flush with the brushroll. also you have to take the screws out of the self propelled uni ... Vacuums
Cannister model#11627915701. connector terminals in extensionwand ,and wlre harness in hose handle get hot,,,look a bit singed.. can order and do ourselves. but would like a "tune up " ,cleaning of vacuum as well. purchased in 2008. have long haired dog,,,can't afford to be without it for very long. have sears store in clay ,ny. lady I spoke w/ says it would get sent out and take at least 2 weeks.!
... Kenmore Vacuums
I have a Royal 7910 extractor and even though I vacuum before cleaning the carpet, by black cocker spaniel's hair gets pulled into the plastic pick-up attachment and I cannot find an easy way to clean it out. I have tried taking the screws out to separate the halves, but it seems as though they might be glues together. I have run water from a sink sprayer though the openings with some degree of success, but it still is pretty cruddy. I have tried snaking pipe smokers pipe cleaners up the pick
One person wrote this in a review:\015\012Most home carpet extractors are very difficult to take apart for cleaning and maintenance. The Royal 7910 is the exception. No tools are needed to take the front housing off to clean out all the pet hai ... Royal CE7910 Wet/Dry Vacuum
Dyson DC 14 hose has no suction, with or without brush attachments. Hot air shoots out from the base of the canister when I try to use the hose. I cleaned the top filter, but can't figure out how to remove the hepa filter to clean it without destroying the case. It looks like it might take three hands to insert pennies and "flip" the case open as is suggested on a youtube video for a different model. Would this even help, assuming I could get the thing open?
... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
I have a dyson dc07 original that i bought used. Last owner was obviously a pet owner and the machine smells too bad to even turn on in the house...can I clean the canister with water? What other parts can get wet or is there a better way to remove the odor?
Put some vac freshner in the canister put the vac out side if its fine plug in and switch on leave runing for around 10 minutes that should solve the odour ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Suction fine whe first switched on but soon (2 minutes) starts to die as a burning smell gets stronger. Filter cleaned. no parts feel hot to touch. What could be the problem. Machine used daily, approx. 6 years old.
Check belt for beater bar ,also check where motor pulls in cooling air ... Vacuums
Hoover windtunnel motor is running rough and overheating, even after clearing the hoses and removing the belts. Could there be something jammed in the blower? How do I get in there to clean it out?
... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
It starting to put out a hot type smell. I have tried cleaning the filters real well and even tried to see if there was problem with the ozone filter. We have checked and could not find a jam. I know the hose has excellent suction. The vacumn works but the intelliclean sensors will not. It only takes about 15 seconds or so for the odor to start. Then it gets real strong and it makes my eyes water
Hi,The hot smell could be from the belt or the motor. Turn it on for a moment, turn it off, then flip it on its side and smell the belt that drives the brush. If that is where the smell is coming from, then your belt is burning up. ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum
We have a Singer 626 sewing machine. It's an old mechanical machine with heavy metal parts. The stitch selector was stuck, I removed the top and helped the selector to move. when I had to move the selector again, it was stuck and I pushed too hard and broke a component. I can fix the machine if I had a repair manual. I need to buy a repair manual. How and where can I get one? Thankjs Charlie PS. Im pretty mechanicly inclined and I was able to clean the machine and get it to work after
I have a dyson alergy machine, I have emptied it, but I would like to clean the filter. I can't locate where the filter is or how to get to it to clean it. The manuel for this is not with the machine. This machine came with the house we live in. Could you help me please? Laurie
Greetings Irlawren3, \015\012\015\012It all depends on the model you currently have. The filters on some are above the motor and some are on the side housing. Its pretty clear looking at the unit where the filters are located. I would su ... Vacuums
I have bought a HOOvER freespace 2000W cyclonic vacuum cleaner but it runs VERY HOT and I am wondering if this is the usual running temperature. I have cleaned the air intake filter and removeed the e
The handle for my Eureka 5993 AVZ was getting very hot when used. Finally, the wires around the switch melted and now the vacuum will not work. What is wrong? Is the switch bad? The wires only melted in the immediate vicinity of the three-prong switch. Nothing else appears to be wrong; the vacuum worked fine when it was running - except for the handle getting hot. Thank you!
Try cleaning all...\015\012if have sam paoblem need replaced main motor.... ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum
I purchased a brand new Techno 1000 Fog Machine last Halloween. It worked fine, but once I ran the cleaning fluid through the fog machine only heated up and produced no fog. A year later and now won't even heat up at all, even after replacing the fuse!
Some one just gave me a Salton Cappuccinoa Dolce Model PE-70 Pump - Espresso Maker and there where no instruction or user manual on how to run this machine. I would like to get a user manual or the instruction on how run this machine.
My iRobot Roomba runs for about ten minutes, then shuts off. I can keep pushing the clean button and it will run for another ten minutes and stop again. Nothing seems to get clean.
Take the brush rolls out and you should see a copper disc. It is the dirt sensor. Clean it with Windex or some other cleaner. This works sometimes. ... iRobot Roomba 550 Vacuum
I have a Hoover Elite Rewind vacuum. Actually,this is my second one. However, after about 4 months of use, it emits a "sour" smell when I'm using it. I empty the cannister before each use and clean out the filter monthly. My house has mainly hardwood floors, so I typically only use it on area rugs and 2 small carpeted rooms. Is there any way that I can get rid of the smell? I've tried putting a dryer sheet in the cannister, but this gets stuck in the filter mechanism. Also, carpet fresh clogs th
Does it smell like an electrical burning odor? could very possibly be the motor going bad already. ive seen it happen. but if not try freshwave odor absorbing pearls. i carry it in my store and we do have shipping. Truly the only thing you should use ... Hoover U5507900 Elite Rewind Bagless Upright Vacuum
Keep getting message 'please remove and clean Roomba's brushes'. Have removed and cleaned brushes and even fitted new one's but still getting message. Also brushes sometimes rotate, sometimes not and not picking up very well at all. Help!
Must be your inbox is full, Delete old / unwanted messages. It should resolve the problem ... iRobot Roomba 500 Series Virtual Wall Lighthouse 80201 Robotic Vacuum
Dyson dc7 quits after a few minutes running; runs again after an hour or two of rest. Filters are clean, beater bar is clean, can't tell about the airways because I can't see how to get to them.
Check the ducts with a small object(screw or something with a little weight)down the ducts to verify they are clean. Also check the Ubend on the back bottom of the unit. Looks just like a U. Remove with a turn of the tab by a screwdriver or quarter ... Vacuums
I have a Z5930 vacuum and i want to trace an electrical fault. I need to disassemble it to get to the electrical connections and it is quite a tricky one to get in side. The machine will run and then cut out after a short time. It will then re-start in about 2-3 minutes and run normally again and so on. I was not able to give you the exact model but it is Ultra Filtration Oxygen line
... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum
Miele Cat & Dog vacuum gets VERY hot and is VERY loud. Hose has no restrictions and I have changed the dust compartment (motor) filter and the exhaust filter. It still gets hot when I run it with the top open and all filters removed, so I'm guessing the problem is with the motor. Should I be going into the motor compartment? If so, what am I looking for?
Hi\015\012\015\012The fact that it gets very hot could be due to a number of issues.,but the fact that it started making a very loud noise at the same time suggests that there might be more problems maybe brushes etc.\015\012\ ... Miele S514 Solaris Bagged Canister Vacuum
Cleaned and running well, taken downstairs, put to work my 530 has developed a distinct knock. about 1/2 second speed as going along. does not happen if brushes removed. machine runs for a few mins th
Click the link below :----http://wikisolutions.blogspot.in/2012/02/get-free-answers.html ... iRobot Roomba 530 Robotic Vacuum
Restrictive valve moments after starting the vac the red ball rises to the top and the machine quits sucking. I turn the machine off, the ball drops, I turn the machine on, the ball rises the machine quits sucking, I turn the machine off the ball falls, I turn the machine on........etc. What am I doing wrong? It works fine and then all of the sudden it starts the same stuff again. I thought it was because the retrieving container was getting too full or the cleaning soln container was not full e
The foam filter on the bottom of the tank lid is too far up. Pull it down so you have at least a 1/4 inch gap from the top. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
Our beautiful Bernina 730 sewing machine has been stored in the garage in its original case, and that wrapped in plastic, for a few years now. Temperatures have been both hot and cold in the garage, but the environment was dust-free. We have brought the Bernina in, set it up, oiled it as specified in the manual, with the original sewing machine oil. We have correctly threaded the machine and the bobbin thread is up. When we press on the pedal to sew, the machine gets electricity and buzzes
Hello and thank you for using Fixya ....From what you describe there can be only 2 causes...Either the machine is still stuck ..and the motor buzzes cause it can not spin it ..and in this case it needs to be oiled more..and be spun by hand unt ... Vacuums