Having problems with your Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum ?

Can not find a proper fitting v-belt to fit my hoover wind tunnel cyclonic. i even ordered it from hoover.


Answers :

The correct belt is # 38528034 ( package # 40201200 ) This belt may seem loose when it is installed, because there is an "idler bearing" that pushes down on it when the handle is released and dropped back.
Repair Help & Product Troubleshooting for Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Can not find a proper fitting v-belt to fit my hoover wind tunnel cyclonic. i even ordered it from hoover.


The correct belt is # 38528034 ( package # 40201200 ) This belt may seem loose when it is installed, because there is an "idler bearing" that pushes down on it when the handle is released and dropped back. ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

My hoover wind tunnel cyclone will not even turn on why? no noise no lights nothing


The switch is known to go bad i replaced 7 so far this week ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Hi My Hoover wind tunnel cyclonic stopped working when i was using it. I tried different plug even then it doesnt work . What to do??


If the motor stopped running, it most likely did because it was not being cooled, becuause something was stopping up the air flow. If you have cleaned the secondary filter out and it still stops while running, then remove the exhaust filter cartridg ... Dirt Devil Hoover Uh70085 Pet Cyclonic? Upright Vacuum

Hoover Wind tunnel cyclonic is dead. Will not


... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

Hoover Wind Tunnel U6458-900 Self Propel doesn't work - via other expert advice here for other models of Hoover - I'm thinking it is the actuator that needs to be replaced as I can see the cable does not connect to anything on the bottom. My problem is - I can't get the cover off. Been trying for a couple of hours. I removed every screw I can seem to find but something is hold it down. I also am wondering if/when I do eventually get the cover off, would I need to replace the cable when I replac


On some models there are hook/springs that hold the cover of the base snug. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover wind tunnel not picking up properly - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum


My turbopower 6200 does not seem to be picking up. The beater bar I don't think is working? ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Folks, My wife and I own a three-year-old Hoover U6434-900 self-propelled "Wind Tunnel" upright vacuum cleaner. The problem is that, even on the highest setting (front-end as high as possible), it gets bogged-down in even shallow pile carpet to the point that the brush stops. I've cleaned the machine thoroughly, pulling hair, thread, dental floss and such from the brush (and everywhere else), including unscrewing the brush end caps and pulling out the cat hair mats which formed in there.


Check to see if the V belt sits too deep in the brushroll groove, if it sits too deep you will need to replace the brushroll. the top of the belt should be about flush with the brushroll. also you have to take the screws out of the self propelled uni ... Vacuums

Hoover wind tunnel


Did you check down by the brush roll for a clog in the dirt inlet. And is the brush roll turning freely, if it is being lugged down, it can cause the motor to overheat and the thermo protector will caught it off, until the motor cools down. But if ... Vacuums

My Hoover Wind tunnel has even a cheaper on/off switch and now, you can't buy a new one. I used to go to their website which had a wonderful diagram of the 'guts' but now the only parts are the obvious ones, belts, filters etc....I have to vacuum twice a day and I should be the test person cause its on and off on and off, but now for a vacuum I purchased 3 years ago for over 200 bucks and I can't fix it myself really makes me made or do you know where I can get this part? help? if not, I will ne


Have you tried going to appliancezone.com? I go there when I need parts... ... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

Hoover wind tunnel cyclonic U5780900 1 year old. brush will not turn. too much slack in vbelt when in carpet position. Belt is good


Well, the V belt is normally fairly slack until the handle is dropped below 45 degrees, which is when the belt tensioner assembly drops into place. If turning the brushroll by hand when the vacuum is in this position fails to rotate the self propel p ... Hoover Vacuums

Hoover wind tunnel + cyclonic


Im pretty sure there are a series of screws that hold it together ( look down into the bottom of it ) once those are all out then it should just pull apart. be careful if it fights you than double check for any other screws you might have missed, the ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Hoover Turbopower Wind Tunnel V2 - clogged - cannot find a way to get at the clog - HELP!


I took off the bottom black piece...removed the brushes ..took a coathanger and went down in silver dollar sized hole and got a big clog out...i also removed the black hose on the back at the very bottom...and used a coathanger up in there as well. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Where can I find an extension hose and wand for a hoover wind tunnel bagless canister model S3755 (59134002)


WHERE CAN I FIND AN EXTENSION WAND FOR MY EURO-PRO ULTRA STEAM SHARK II  EP908? ... Vacuums

Hoover wind tunnel cyclonic with hepa filter just stop working. Model No U5781900. Had this item close to 2 years. Has the motor burnt out? My e-mail address is [email protected]


... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Hoover wind tunnel


Replace the HEPA filter with a Hoover filter. Don't use the Arm & Hammer brand sold at Wal-Mart because these filters have an aditional layer to hold the air freshener which restricts air flow causing the filter to clog faster making the unit ove ... Hoover 5416-900 WindTunnel Bagged Upright Vacuum

The on off switch is stuck in the on position. I can'tfigure how to take the handle apart. Where can I find an on-line manual? Hoover wind tunnel up-right.


On the windtunnel the switch is not in the handle. It is located in the top of the body housing underneath where the handle meets the body. The slide lever you are pushing on to make the machine run is just a push rod. ... Vacuums

No suction i have a hoover supreme wind tunnel vac and its relatively new and the suction, well......sucks. It wont pick anything up! I am extremely frustrated! I picked up a ball of fuzz off the carpet and held it under the vacuum and it still wouldn't **** it up. I then shoved the fuzz up INTO the vacuum. It fell right back out. I may as well not even vacuum. Please help!


I have found more vacuums on the way to the dump because they were full. Check. Is it full?\015\012If not the air way is clogged. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Height Adjustment on Hoover Wind Tunnel doesn't seem to do the job.


... Vacuums

Hoover Wind tunnel V2


Either the brush rolls are bad, ends are bad, or the gear housing/motor asm. is bad and will have to be replaced. ... Hoover U8147-900 WindTunnel V2 Bagless Upright Cyclonic Vacuum

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless


Get over it and buy a new one!!! ... Vacuums

How to replace the tension spring on a hoover 5454 wind tunnel


... Hoover U5454-900 WindTunnel Vacuum

Hoover Wind tunnel self propel not propelling - how do I know if it is the belt or the idler arm?


... Hoover U6485-900 Windtunnel Bagged Upright

Hoover Wind Tunnel Upright Self-Propelled


Thanks to reddevil6. Sure enough it was the belt. What I did was take off the belt and flipped it over, worked like a charm. Since it was stretched on one side the other side was still ok. Still need a new, but s aved me a trip to the store! ... Vacuums

Lost Manual for Hoover Turbo Power 8000 Wind Tunnel


... Hoover U5453-900 WindTunnel Supreme Bagged Upright Vacuum

Hoover Wind Tunnel


What probably happened is you swapped end over end when you replaced the beater brush. anyway go to thehooverstore, find your machine and you'll see an exloded diagram of your machine. ... Hoover Company Wind Tunnel U53019 Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0681 seconds