Having problems with your Hoover U6311-930 Power Drive Bagged Upright Vacuum ?

Hoover U6317-930 - Turbine Locked Up!

\015 Something got picked up and is lodged inside the turbine, preventing it from turning. Is there a way to disassemble it to get inside the turbine? Thanks!\015

Answers :

You will need to remove the hood as though changing the belt. Then best to detach the handle/ bag chamber with the black screw at the lower end in the center.
Lay the vac flat and you should see two clamps over the motor housing, one on either side. Undo the clamps and the motor will lift out. There will be four more screws holding the fan shroud onto the motor housing. Remove these and detach the fan end only. Installation is the reverse order. The fan itself will unscrew if replacing,just secure the motor shaft without damaging it.
Polish the motor shaft clean for a new belt, removing burned rubber. I use 600 grit wet/dry sandpaper or steel wool.
Any evidence of a damaged fan blade means a new fan is required.
While you're at it, unscrew the end caps on the brush roll and remove the hair and thread. Then reassemble so it spins freely when holding the end caps. Install a new genuine belt. It will be snug, use the brush to pull it into place.
When reassembling be sure to engage the carpet height control through the lid
If this helps please acknowledge. If not psot back with the next problem
Repair Help & Product Troubleshooting for Hoover U6311-930 Power Drive Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover U6317-930 - Turbine Locked Up!


You will need to remove the hood as though changing the belt. Then best to detach the handle/ bag chamber with the black screw at the lower end in the center. Lay the vac flat and you should see two clamps over the motor housing, one on either ... Hoover U6311-930 Power Drive Bagged Upright Vacuum

Hoover Power Drive Supreme - Locked Up!!


Q: Are you talking about the turbine powered hand tool that attaches to the hose? If so, just squeeze the two round pins on the sides, and the housings will separate. ... Hoover U6311-930 Power Drive Bagged Upright Vacuum

I just bought a Samsonite "Freeminder Flex" backpack with handle. My issue is with the lock... The combination for this lock was set to open at 0-0-0. It opened and locked perfectly at first. But after following the instruction to set up the new combination code, it doesnt lock anymore....please help and thanks! Linda


... Vacuums

Wheel in Hoover SpinSrub turbine broke


The turbine is the only way to go. ther is no way to get that part only. Your only option to find a used one is to call on other hoover dealers if the have a box of used parts that fit your model. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover steam vac all terrain turbine gear assembly


Hello,\015\012\015\012I'd be happy to walk you through this repair. Unfortunately this is a very common problem with the Hoover SteamVacs. \015\012\015\012Here's what you'll need to complete this repair:\015\012- ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

Hoover dual v steamvac turbine repair - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My Hoover Z 400 collapsible vacuum won't lock in the upright position. I pull the pin to change from a cannister to an upright, but the unit won't lock into position


This just happened to me. i took the vacuum completely apart and found that there is a locking plastic "tooth". this had snapped off but still it the track. the damage was bad but i was able to wash of all the lube off it and used a 2 part epoxy glue ... Hoover F5858-910 SteamVac Vacuum

Hoover windtunnel tilt mechanism won't remain locked in upright position or at any of the fixed angle positions - now any slight bump and the lock releases. Normally you must manually use the small foot pedal release on the left side as you face the vacuum from behind.


Hello, stanI was trying to help you out here. Maybe this will help some? I was going back to some customers that asked questions in the recent past and even farther back. It appeared that no one answered some of them, So, I thought I ... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

How to replace turbine on hoover steamvac - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover turbine replacement


First you must remove the dirty water tank then the nozzle window on top of the machine. (this is the clear piece that the dirty water is sucked through.) then remove all 8 screws from the bottom along with the 1 screw on the main housing. after all ... Hoover F7431-900 SteamVac Vacuum

My Hoover vacuum model - U6317-930 lost power. I


Something is definitely loose in that area. Replacing the related parts is probably the best fix. ... Vacuums

Stuck Brushes on My Hoover SteamVacV2 Turbine Help!


Did you pull the brush block out to see the the shaft hasn't broken off of the brush block? If so, then replace the brush block. From the bottom, take the screws, 2 of which will be longer ones, these hold down the turbine . Turn it over and the t ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Hoover Steam Vac Dual VModel #F7430-900 the turbine does not turn


... Hoover F7220900 SteamVac V2 Upright Vacuum

Hoover steamvac turbine and brush control switch


Try checking your drive belt might have come of or just loose ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover Steamvac handle won't lock up.


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Turbine locked up


The brush block is just held in by clips, just use a screw driver to pry it out. There are 6 screws on the bottom that need to be removed. 2 where the brush block was, just alittle back from there are 2 more. Then near the edge on each side, are ... Hoover F7220900 SteamVac V2 Upright Vacuum

Replace turbine or control switch for Hoover F7412-900?


... Hoover F7412900 Upright Vacuum

Hoover steam carpet cleaner - turbine needed for F7458-900


Once you get the turbine out, open it up by unlatching the three latches and unscrewing two screws. Pull the gears out and WD40 everything. Let it sit for a bit and start turning the solver gear at the back with a pair of pliers. Once it is loose, pu ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Replacing turbine on hoover max extract


... Hoover F7431-900 SteamVac Vacuum

The brushes will not spin anymore and the switch to go from spin to locked does nothing this is on a hoover steam vac shampooer


Pull out the brush block, make sure it will turn and to see if the shaft is on it, the shaft goes up into the turbine. If the block is ok, then the turbine isn't working. You take it apart and clean out the turbine, or replace it. ... Vacuums

Steamvac Hoover Were you able to remove the turbine? I just can't find the way to do it. Can you help? Eddie [email protected]


Hi,I am not sure if you will be able to view my solution in your Premium Problem re: Hoover SteamVac F7222-900. With your indulgence, I took th ... Hoover F7220900 SteamVac V2 Upright Vacuum

Hi, i have a hoover steam vac agilty. the brushes on the bottom front quit spinning. they are not locked up as i can freely turn them by fingers. is there a belt that i need to replace? if so, how do i get at it to replacec it? thank you for any assistance


The brushes on all hoover steam vacs are air opperated it uses the suction of the vacuum motor to spin a turbine and in turn spin the brushes. Most likely that path of air is clogged with hair or carpet fuzz. On the top of the machine there is a litt ... Hoover Vacuums

Hoover self propelled U6630900 idler arm lock


Remove the bottom plate (4 screws), remove belts and brush roller. There may be 1 small screw in the center front of the vac under the brush roller. remove this one. If this is a bagless model you will also need to remove all of the back screws (torx ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0559 seconds