Having problems with your Hoover U6311-930 Power Drive Bagged Upright Vacuum ?

Indentations left on carpet all about 3 inches apart

\015 Hoover Power Drive vacuum has begun to leave indentations on carpet. They appear to come from the metal part that runs along the carpet. I have changed the setting to high and indentations still appear.Your opinion please.Ruth M. Fletcher\015

Answers :

The indentations that the Hoover U6311-930 self propelled leaves are from the two large wheels of the self propelled system under the bottom of the vacuum. There are two main reasions for this the weight of the vacuum cleaner and that the carpet fiber has worn, do to age, and now shows the tracks. There is no sollution for this problem.
Repair Help & Product Troubleshooting for Hoover U6311-930 Power Drive Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Indentations left on carpet all about 3 inches apart


The indentations that the Hoover U6311-930 self propelled leaves are from the two large wheels of the self propelled system under the bottom of the vacuum. There are two main reasions for this the weight of the vacuum cleaner and that the carpet fib ... Hoover U6311-930 Power Drive Bagged Upright Vacuum

Motor doesn't run I believe it the brush on the motor. two motor brushes one is completly gone about 1/8 inch left could this be the problem.the other motor brush still has 1/2 inch left. and current to motor tested good.


Sounds like your belt slipped off. ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

We have a Bissell Proheat Cleanshot 2X Model 9500 Steam carpet cleaner. The first time we used it things were great. The second time we used it it left tracks in the carpet. We have no idea what caused this. We tried using the machine on an entirely different carpet and it did the same thing. After vacuuming the carpet about 10 or 12 times, the tracks are still embedded in the carpet - HELP!!!! We're read and reread the manual and contacted customer service and received no help.


First things first. It's only the second time you have used the machine, so it must be fairly new. If you have a receipt and the unit is less than a year old you should take it to an authorized Bissell repair center and have the machine inspected und ... Vacuums

Just bought and used the Hoover MaxExtract 77. First time the water was extracted from the carpet. Second time NO water in tank. Now I have wet carpet. I've taken the machine apart 3 times and cleaned the filters and still the water is not extracted from the carpet.


... Hoover F6055-900 SteamVac Maxextract LS Wet/Dry Vacuum

With cleaning carpets with the Stowaway when the head gets a blockage it makes a high pitched whining sound and requires unblocking - then works fine. Now when vacuuming the head always makes the same sound when the head is against the carpet. you can also see that the rollers are slow or stopped. We have pulled the Stowaway virtually completely apart and checked for blockages as well as washed the filter and no difference. Any ideas?


... Dyson "Stowaway" Canister Vacuum Vacuum

Bissell 7901 Proheat Carpet cleaner water will not come out. Everything else works but it just will not wet the carpet... I have took apart the handle n I do not know where to put the spring back. Please Help


... Vacuums

Hoover model U6476910 I was cleaning out the bearing sections of the brush when a spring type pressure washer fell on the floor. I did not see the washer when I took it apart and I can't tell where it goes in order to put it back together. It is very thin and measures about 5/8 inch with an 11/32 inch hole. Frank Nething


Hi frank this sounds like its a compression washer, you normally find these on the end of the roller to even out any movement from side to side, as you look at the hoover's brush head, it should slip into a groove on one side with the roller...hope t ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.


The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

My bissell 1699 series will not spray water, the flow indicator barely moves, but when left tank on it leaked all over floor, so the water when left unattended came out. When I first hooked up the machine black stuff was on my carpet when I first sprayed.


... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

My carpet was dirty in spots. after using my pro heat , the whole carpet is dirty. some of the dirty water came out at the sides and left blotches of dirt every where I pushed it. I am so disgusted. I've only used it 3 times and it's never been satisfactory.


Dont fill water tank so full and change water more often. Home units are made for smaller jobs thats why rug doctors and others unit can be rented. Different systems altogether. ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

My Bissell Proheat Turbo has poor suction and leaves the carpet too wet. Is there a way to improve the suction so the carpet will be left just damp not soaking wet?


Flip the unit over you will see a grey panel that looks like a V with 6 or 8 screws remove it and you will find a black cover I think it has 2 screws remove it and you will see a gasket seal for the bottom for the motor mine was white some times ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

How to take apart the Hoover U6437-900 to change the belt and clean it. I have the belts and I have removed several screws. It looks like the knobs for the wheel carpet height and carpet to floor selection are the problems but I can not figure out how to remove the knobs. Besides, I am not certain if this is the problem. Do you have the instructions? Thanks


HERE IS THE MANUAL > http://hoover.com/file/500/ ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Brushes stop rolling when against carpet, yes it is out of the upright position and when I left the base off the carpet the brushes start to roll again. What is wrong?


Your belt is stretched out so it just stops when the carpet resists it. Get a new belt made for your particular machine and you should be back up and running ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Everytime i try to use in carpet mode it makes a grinding noise i took it apart but it looks like a sealed unit is there a fix for this?


Go to http://www.dyson.com/support/help.asp?article=2select your model, and see the guide troubleshooting , proceed with common sense. and fix it.God bless youSometimes you must check noise, from bloackage, debris, dust, or fan blades mot ... Vacuums

How to remove the residue on hardwood floors left by carpet pads?


... Vacuums

Bought a ultimate g off trade me and it has left marks all over the carpet - am wondering why may be the problem - I have cleaned the outer bag and cleaned the rest of the outside - I am renting and n


Dirt build up on rug plate, or copy belt on m/c ... Kirby Ultimate G Bagged Upright Vacuum

Bissell 7901-1 The soap doesn't mix with the water when I pull the trigger, I can see the soap isn't being used when I do the carpets. What can I do, have no problem taking this machine apart.


If the mix valve knob is turning smoothly, then most likely the cap and valve for the sop bottle is bad. Also make sure that the seal is on the cap at the bottom of the bottle and not sitting in the hole. ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

The brush wouldn't work when the selector switch was in carpet mode. Took the power head apart and removed the motor. Everything o.k. in the power head. Checked and found that the neutural wire had pulled out of the connector, the connector was never crimped at the factory. What a day! Took 2 hours and a large pizza to get it done. Neutral wire was in the hose just below the handle. Reconnected the wire and crimped it, put everything back together. It works!!!!


Great. ... Kenmore Vacuums

Hoover tempo upright is clogged. I can only vac for a few minutes, then I have to unplug it and turn it over and clean out the under part under the roller. It is totally stuffed with dirt and dust and carpet fibers. I have a new bag in. It is like it is clogged up inbetween the bag and the roller. Also gets clogged when using the hose. It is maybe a year old. How can I take it apart and unclog it?


Disconnect the hose and head and wands. Drop a quarter thru the hose, the handle sometimes clogs. peer thru the wands and inspect the elbow on the head for blockage as well ... Vacuums

It will empty the cleaner but will not spray water filter is clean spray heads were taken off & i could blow threw them is it a case of no prime in pump if so should i fill pump i had this thing all apart and i now know evry inch of this matchine when i pull the triger it sometimes will spray for a sec.but thats it i also took the switch out and air goes threw when i press the switch if it is the prime in the pump how can i fill the pump . what hose on the pump will prime i thankx for your advic


The problem is most likely that your pump belt is worn, stretched or broken. Here you can get the belts you need and view the manual:htt ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Bissell Powersteamer 1694W won't extract water from carpet. Was extracting fine until the pump/brush belt gear broke off off the pump. I repaired the gear with super glue and the brush is once again working fine. I now have an extraction problem. What did I do wrong? I took it apart and was so proud of myself when I fixed the original problem. Now I'm lost.


Check your re-assembly.\015\012\015\012Have you missed a pipe connection somewhere? ... Bissell Powersteamer 1694 Upright Vacuum

My sebo does not seem to be picking up stuff off carpet, what can i do. When I use the hose apart from the vacum it does having sucking power.


Unlike most vacuum cleaners, the Sebo Felix has two separate motors - one for the suction and one to drive the brush roll - so there are several things to check. You say the hose has suction, so the problem is in the lower part of the machine. First, ... Sebo Felix Classic Bagged Upright Vacuum

We just bought the Bissell 9500 ProHeat, but in our first use, it left the carpets VERY wet. Is there something we can try, or do we have a defective unit?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Power to power carpet head


Once again remove the electrical connections and clean it and also blow the dirt and then fit it tightly and carefully.if anything broken inside replace it. ... Miele S548 Bagged Canister Vacuum

My Eureka Boss Widetrack leaves debris behind while sweeping. I have the setting for carpet and debris is left behind on the floor.


Check for blockages in the brush bar compartment and hoses ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0358 seconds