Having problems with your Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum ?

How do I get inside to install the new cord? Model #U5445-90

\015 I took all five screws off but didn't want to add to much pressure, should I use more force?\015

Answers :

There are 4 screws on the bottom that will let you take the cover off.that will exopose the motor and the cord.
Repair Help & Product Troubleshooting for Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do I get inside to install the new cord? Model #U5445-90


There are 4 screws on the bottom that will let you take the cover off.that will exopose the motor and the cord. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the


... Dirt Devil M088905 Vision Bagless Upright Vacuum

I have a Hoover Windtunnel U 6439-900. The agitator brush will not turn. I installed 2 new belts, # 38528034, and # 38528-035 There is so much slack in belt # 3852034 (brush drive) that it cannot grip the brush. There does not seem to be any adjustment to take up the slack. I've put in new belts twice now & cannot get brush to rotate or tighten the belt to the brush.


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

We bought a new cord winder for our Electrolux 1205 Canister Vacuum cleaner and we are trying to install it is not turning on. We get it all connected but it doesn't turn on. Is there a reset button or some advise you can give me to get it working? I used a voltage detector to see if there was power running through the cord winder and there is.


Did you put a bag in the vacuum?\015\012I suspect there's an improper wire connection somewhere, but there are other things that could cause this I strongly recommend taking it to an authorized Aerus Electrolux dealer and letting a trained tec ... Electrolux Vacuums

My HEPA filter get's blown off of the vacuum when I vacuum. I just got all new filters and a new brush roll. Could something be clogging in the inside?


There should be a cover that closes over the HEPA filter. If the cover is missing, or is there, but does not snap closed, then either snap it closed, or replace the cover.If something was clogged inside, then the HEPA filter would be less prone ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Getting inside the cyclone canister of the new Dyson DC 33


... Vacuums

Where can i get new fiters for the inside - Filter Queen Majestic Canister Vacuum


... Filter Queen Majestic Canister Vacuum

I have an Electrolux Renaissance Vacuum C104H. How do I get take the hose off of the handle to install a new hose but keep the handle I have?


... Vacuums

Beater Bar The "Beater Bar" or roller with brushes on it, is not spinning, therefore not picking up. I cannot locate my manual and need to know if it is belt driven and how to get at the belt to identify the size and purchase and install a new belt. Thank you for any assistance. [email protected]


Take off the bottom plate, then you can get to the brush roll and belt, on the model number plate, the number of the belt is on that, it is also on the belt if you can still make it out. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Trying to install my new singer futura ce250 i have downloaded the patch to get it to work with my computer now it gives me a error on the computer screen something with security


My guess is that you should uninstall the software re-install the file as administrator or with administrator privileges\012\012Unfortunately you do not give details of your operating system, XP or vista etc but in general right click on the in ... Vacuums

Hi, the seal from the impeller and pump shaft leaked. got new seal kit and installed. only disconnected the contacts piece to get clean attachment to shaft and the points now stay together looking like the springs are frozen thanks for your help


Hi ggetman38...\015\012\015\012That is normal\015\012What you are talking about is the centrifugal switch, they will swing apart when the motor rotates, they are there to start the motor with the points touching each other at motor ... Vacuums

I can't get the filter door to shut after installing a new generic filter.


Is there one of the attachments (If this unit stores attachments under this door?)-- is one of the attachments just a little out of its 'proper' spot?Sometimes generic filters need to e trimmed down, to fit better than manufacture specifi ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

I have a bissell lift off and the brushes wont spin, i think it maybe because of the internal switch that tells the vacuum that the canister is installed is bad. is there a replacement part for that or do i have to get a new vacuum?


Hi,If you take out the brush roll, holding the ends, make sure that it \015\012spins freely, if not, replace it. Belts stretch after a short time of \015\012use and need to be replaced often.So you could either have a bad brush roll and ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

The roller turns strong and the belt is new,but the dirt accu-mulates and doesnt get sucked up! there no observable clogs and the filter side vent blows strong.......ive removed beater,belt and am assuming there may be a problem inside the motor housing as all else appears normal..i was an aviation mech in the military and the above is my assessment........


Are you sure you have the belt on correctly?\015\012If it is not, the beater brush will push the dirt, etc, in front of itself and not back to the suction port. ... Hoover Tempo Widepath Upright Vacuum - Blue

Electrolux epic 6500 turns off with new bag installed and hose removed. How do I get the control valve out to check it...?


... Electrolux LE, 2100, 6500 Canister Bag Lock Out Valve

Sunbeam water dispenser YLR2524H2 - the hot water lever broke and I need to know if I can get a replacement part and can I install the new one myself?


... Vacuums

I HAVE A BISSELL MODEL 7920-3 AND IT NEEDS A NEW BELT. I WANT TO KNOW WHERE TO GET A BELT AND HOW TO INSTALL IT. THANK YOU, GARRY


Check here for beltcheck here for how to and belt ... Vacuums

I installed a new battery in my Roomba 540. It charges and runs directly with power cord but will not charge on dock. When I push the dock button, it acts like it "sees" the dock and approaches it and even slides on, but then gets back off again and just keeps going back and forth until I turn it off.


... Roomba Robotic Floor Bagless Vacuum

My dyson animal works for a while then shuts off...i guess it's getting hot and automatically turning off to keep damage from occuring. i have cleaned the filter and all the collection basket, but am still ahving problems. it was just services a year ago and a new switch installed. please help!!!


The belt that drives the beater bar may be broken or stretched, causing the motor to turn more freely, therefore causing the motor to rev beyond it's design.Jim ... Vacuums

I have a Genie 200ph wet/dry vac. it has a long thin bag inside that catches everything. where can I get new ones and a manual


... Genie Company GV150 Wet/Dry Vacuum

Jun 24, 2010 - Jun 24, 2010 - Needle not bent/ new needle not answer. I finally conclude that the entire bobbin case is ROTATING in its seat, which jams the needle. The "projection" is against the "spring" when I install it, but I can rotate the bobbin case PAST the spring without trying very hard. Bobbin case MIGHT get held in place better if it were closer to me (front of machine). I feel it is still not out from under needle plate as shown in diagram, but can't keep it closer to f


Hi,Your problem dated 24th June 2010 was re-posted today. If it has been already resolved, kindly ignore this message.Thanks for using FixYa ... Vacuums

How do I install new hose on little green 1400-5


... Bissell THE BISSELL LITTLE GREEN MACHINE Vacuum

I have an Hitachi vacuum cleaner, bought a long time ago CV99. It is the best! My daughter borrowed it and lost the seal around the middle. Can I get a new seal? Or where in New Zealand could I get a new Hitachi?


... Hitachi Vacuums

Kenmore Model 116 28014700 intuition vacuum cleaner. Latch for hose connection to cannister broke. I have the new part. How do I remove the hose from the broken part and replace it on the new part? I have already purchaed the new part p/n KC92PDDUZV06 for this, bt can't figure out how to get the old part off. It looks like you must destroy old part in order to get it off.


... Vacuums

The belt wont turn...i cant get in to the inside to check to see if the belt isnt on the roller...how do i get up in there..i took the bottom plate off and you still cant get inside... thx Peggy


The following site has some great info on your machine:\015\012\015\012www.dysonmedic.com ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0764 seconds