Having problems with your Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum ?

How to remove handle from Hoover 5445-900 upright wind tunnel vacuum

\015 The switch is bad on this vacuum. How do I get the handle off and replace the switch? Thanks mary..\015

Answers :

Hoover.com doesn't have a manual specific to your model but there is one similar which will show how to remove the upper handle from the body.

http://www.hoover.com/pdfs/manuals/U5467900.pdf

Do you have a replacement switch? If not I believe you can buy one from Hoover (the switch and/or the upper handle assembly). Unfortunately your model isn't listed on the website, is this a new vacuum? I recommend giving them a call, that would be the easiest way.

Also remember when working with electronics to unplug the vacuum. Even when there is no power residual electricity can remain in the wires. If you feel unsure, take it to a repairman.

Hope this helps!
Repair Help & Product Troubleshooting for Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to remove handle from Hoover 5445-900 upright wind tunnel vacuum


Hoover.com doesn't have a manual specific to your model but there is one similar which will show how to remove the upper handle from the body.http://www.hoover.com/pdfs/manuals/U5467900.pdfDo you have a replacement switch? If ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Wind tunnel by Hoover, vacuum will not turn off by using switch on upright handle. do not see a way to get to switch. modle no. U5458-900


Follow the cord and look for screws inside the bag compartment at the top. a panel should lift off allowing access to switch and cord. If swtch is melted it must be replaced with special hoover switch kit which has new wire and heavier duty switch. b ... Vacuums

VACUUM REPAIR I have a Hoover Savvy upright, windtunnel, bag/bagless vacuum (model U8150-900). The Handle Release Foot Pedal - Part #38434026 broke soon after purchase but I finally found a source to replace this item. The problem is that now that I have the repair part I cannot figure out how to remove the old pedal and install the new one. The housing appears to be one piece of solid plastic. Any ideas, PLEASE! Peter


There are 2 tabs that stick out on the release, they fit in slots, so from the top look down and you can see them, using a flatblade screwdriver that will fit in there, push the side in to release it, which isn't easy, but it can be done. When you g ... Vacuums

Hoover wind tunnel not picking up properly - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum


My turbopower 6200 does not seem to be picking up. The beater bar I don't think is working? ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Replace power cord Hoover U5757-900 - Hoover Company Wind Tunnel U53019 Upright Vacuum


... Hoover Company Wind Tunnel U53019 Upright Vacuum

Hoover wind tunnel PAWS won't suck up - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old


Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Wind tunnel t series vacuum won't turn on - Hoover WindTunnel TSeries Bagless Upright Vacuum Cleaner UH70107


I had the same problem and used a tool to clean out the suction tube on my Windtunnel Series T. It was full of junk packed in tight. After cleaning it out there's no more turning off or overheating. It actually works better than when I first got it ( ... Hoover WindTunnel TSeries Bagless Upright Vacuum Cleaner UH70107

I forgot to replace the vacuum cleaning bag in my Hoover Wind Tunnel Supreme Mach 3.3! It overheated and turned off. I spent all afternoon cleaning the dirt out of the inside, filters, etc. It still overheats when used over 1 minute. Do I need to buy a new vacuum?


... Vacuums

The handle comes off my Hoover Wind Tunnel PAWS vacuum model #UH702010


... Vacuums

Can I get a replacement handle for a hoover wind tunnel upright? It snapped off


That part is available. Includes the handle, cord and "digital" switches. Here's the link:http://www.vacuummedic.com/product.php?id=389Goo ... Hoover UH30010COM Bagged Vacuum

Hoover wind tunnel bagged platinum upright vacuum shuts down while on carpet. Works fine on tiles.


... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

On my Hoover 6660-900 bagless upright self propelled wind tunnel vacuum when I replaced the cable which works the power drive, there is a spring next to the control arm which I cannot quite figure ou


... Vacuums

Hoover, model # UH30070 Wind tunnel vacuum Brush won't turn. I do not see how to remove this to replace the brush, and besides it's only about a year old! Why is it already broken? There's no visible evidence on the brush that would make it stop, i.e. string, clogged, etc. Can you help?


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Folks, My wife and I own a three-year-old Hoover U6434-900 self-propelled "Wind Tunnel" upright vacuum cleaner. The problem is that, even on the highest setting (front-end as high as possible), it gets bogged-down in even shallow pile carpet to the point that the brush stops. I've cleaned the machine thoroughly, pulling hair, thread, dental floss and such from the brush (and everywhere else), including unscrewing the brush end caps and pulling out the cat hair mats which formed in there.


Check to see if the V belt sits too deep in the brushroll groove, if it sits too deep you will need to replace the brushroll. the top of the belt should be about flush with the brushroll. also you have to take the screws out of the self propelled uni ... Vacuums

Wind tunnel supreme will not start - Hoover U5453-900 WindTunnel Supreme Bagged Upright Vacuum


... Hoover U5453-900 WindTunnel Supreme Bagged Upright Vacuum

Jammed retractable cord - Hoover Company Wind Tunnel U53019 Upright Vacuum


... Hoover Company Wind Tunnel U53019 Upright Vacuum

Hoover Wind Tunnel Upright Self-Propelled


Thanks to reddevil6. Sure enough it was the belt. What I did was take off the belt and flipped it over, worked like a charm. Since it was stretched on one side the other side was still ok. Still need a new, but s aved me a trip to the store! ... Vacuums

Hoover wind tunnel 2 bagless vacuum not working


Place handle in low position and turn cleaner over so bottom side is up.\015\012Remove the 4 screws in bottom plate and lift off.\015\012Look on the left side of the agitator brush. You should see the belt there. Remove agi ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Too much play in upright part of my Hoover upright wind tunnel


No. The handle release pedal is snapped into the bottom base assembly. Look underneath to check for cracks or damage in this area. this is the most likely issue. If it is, then the base will need to be repalced. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover Upright Vacuum model U5470-900 - The On/Off switch on the handle does not properly engage the power switch deeper in the handle assembly. It appears to ride over the lower switch and doesn't engage it to operate it. If I play with it, I can get it to maybe turn on the vacuum, but, then the upper handle switch won't turn it off. Our current workaround is to use the power cord for on/off operation.


... Hoover Vacuums

How to remove the bag housing from the handle in order to replace the power cord on a Hoover vacuum U5209-930


... Hoover Vacuums

Hoover U5344-950 My Hoover vacuum is a nightmare! I have had nothing but problems with it since day 1. The powerhead stops working if you try to lower the handle to vacuum. I took it in to be serviced and was told it sat on the shelf for too long in the store and it warped the belt...so it was replaced. Got it home, it worked the first time I tried it, then went right back to no powerhead working and as a bonus it is giving off a nasty smell like it is going to blow up! It now gets really hot to


... Hoover U5344-900 WidePath Vacuum

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless


Get over it and buy a new one!!! ... Vacuums

Hoover on off switch won't turn off. I have to unplug the vacuum to stop it. I have dismantled the handle and now I can't get the inditation in the handle to fit over the little silver knob. I saw there was an on/off switch under the handle that is controlled by a piece of the handle. #1 question for the manufacturer is why don't they put the switch on the outside instead of having gimicks that turn it on and off... arghhhhhhhh


Don't know what model you have, but sounds like you will need to replace the switch. As far as your question, you will have to contact the manufacture for an answer. We only provide solutions to your problem and a model number would have helped. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1531 seconds