Having problems with your Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum ?

Need to replace the control cable on a wind tunnel upright.

\015 What do I need to take off or loose to get down to the cable pivot arm to replace the control cable?\015\012\015\012Thanks for your help.\015\012\015\012Mike\015

Answers :

Phillips screwdiver once you get the cover off there will be 4 screws that hold the motor to the base 2 on each side of the upright.its where te upright swivals
Repair Help & Product Troubleshooting for Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Need to replace the control cable on a wind tunnel upright.


Phillips screwdiver once you get the cover off there will be 4 screws that hold the motor to the base 2 on each side of the upright.its where te upright swivals ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

On my Hoover 6660-900 bagless upright self propelled wind tunnel vacuum when I replaced the cable which works the power drive, there is a spring next to the control arm which I cannot quite figure ou


... Vacuums

Hoover Wind Tunnel U6458-900 Self Propel doesn't work - via other expert advice here for other models of Hoover - I'm thinking it is the actuator that needs to be replaced as I can see the cable does not connect to anything on the bottom. My problem is - I can't get the cover off. Been trying for a couple of hours. I removed every screw I can seem to find but something is hold it down. I also am wondering if/when I do eventually get the cover off, would I need to replace the cable when I replac


On some models there are hook/springs that hold the cover of the base snug. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I need to replace the torsion spring on to the valve arm that controls the valve door. I just need a explanation as to how the spring is connected to the two parts. This is for a Hoover U6632900 upright bag-less series.


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old


Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

How to replace filter on a Hoover Mach 3.3 wind tunnel upright vacume cleaner


... Vacuums

Can I get a replacement handle for a hoover wind tunnel upright? It snapped off


That part is available. Includes the handle, cord and "digital" switches. Here's the link:http://www.vacuummedic.com/product.php?id=389Goo ... Hoover UH30010COM Bagged Vacuum

How to replace a Hoover Control Cable U6425 - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I forgot to replace the vacuum cleaning bag in my Hoover Wind Tunnel Supreme Mach 3.3! It overheated and turned off. I spent all afternoon cleaning the dirt out of the inside, filters, etc. It still overheats when used over 1 minute. Do I need to buy a new vacuum?


... Vacuums

Hoover Supreme wind tunnel upright model. I have a bad on-off switch. How do I replace it?


Take the two screw off the handle and then remove the upper handle devise. This will expose the real on/off switch which is on the top of the unit. There is a plastic actuator that rubs up against the switch when slide the plastic switch on the han ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have a Hoover Wind-tunnel Vaccum (Model U5433-900) that needs a new power cord. I am looking for step by step directions for replacing the power cord


... Hoover Vacuums

I need to replace the cable on my Dyson upright vacuum cleaner.


You need to remove the yellow switch, at the side of the switch there is a tiny hole which is there to allow you to push a small implement in which will push the little catch that holds the switch in place you will then be able to pull the switch ou ... Hoover Vacuums

I need to replace the idler arm assembly on a U6439-900 hoover wind tunner upright. I have the clear cover completely removed but still do not see how to remove old and insert new assembly.


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Replace power cord Hoover U5757-900 - Hoover Company Wind Tunnel U53019 Upright Vacuum


... Hoover Company Wind Tunnel U53019 Upright Vacuum

LOSING SUCTION IT APPEARS WHEN IN UPRIGHT POSITION, ALTHOUGH SUCKING (TO SOME DEGREE) IT THROWS BACK SMALL PIECES TO THE BACK OF THE VACUUM OPNTO THE CARPET BEHIND, AND THE CONTAINER HOLDING THE STUFF ISNT WHIRLING AROUND THE CONTAINER. I WONDER IF THE PASSAGE TO THE WIND TUNNEL IS BLOCKED, AND OF COURSE THAT IS THE PART I CANNOT GET TO, AS IT NEEDS A SPECIAL TOOL TO UNSCREW THE BACK OF THE VACUUM.


Is brushes moving, if so it is clogged , usually takes a star bit to take apart to clean ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Hoover wind tunnel upright self propelled. U6473-900. Brush does not work. Heard it was a 'brush controller' problem and can be fixed. Please tell me how.


Most likely the flat belt has stretched enough so as to not turn the pulley that in turn turns the brush roll using a V belt. Also there is a small idler wheel, if hook up, then it won't engage the V belt. ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Too much play in upright part of my Hoover upright wind tunnel


No. The handle release pedal is snapped into the bottom base assembly. Look underneath to check for cracks or damage in this area. this is the most likely issue. If it is, then the base will need to be repalced. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Dyson dc05stduk vacum cleaner need to replace power cable


Hi \015\012\015\012Try this site does manuals on Dc05 repairs.\015\012\015\012http://dysonmanuals.llc.nu ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

Hoover Wind Tunnel Upright Self-Propelled


Thanks to reddevil6. Sure enough it was the belt. What I did was take off the belt and flipped it over, worked like a charm. Since it was stretched on one side the other side was still ok. Still need a new, but s aved me a trip to the store! ... Vacuums

How to replace belt in Hoover U5402-900 Wind Tunnel Vacuum


... Hoover U5402-900 WindTunnel Vacuum

Brush not working on self-propelled wind tunnel U6471-900.I have replaced belt but can't get off top cover.


... Vacuums

How to remove handle from Hoover 5445-900 upright wind tunnel vacuum


Hoover.com doesn't have a manual specific to your model but there is one similar which will show how to remove the upper handle from the body.http://www.hoover.com/pdfs/manuals/U5467900.pdfDo you have a replacement switch? If ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Replacement wheel I broke the wheel on my bissell upright model 3760 and need a replacement wheel and possibly an associated side molding. I can't seem to find replacement parts such as these- any suggestions?


The rear number is 2036627, there is no side casing, you would have to replace the whole back, which Bissell isn't making avaiable. But o get the wheel, you might try bissell.com and see if you can order direct, or try a local repair shop to see if ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Replace belt i need to replace the belt on an upright dirt devil 086310 vaccume but do not have a manual and can not find how to open the assy to replace the belt


On the bottom, there should be a few screws to remove to remove the plate covering the brush roll. However some may have screws on the top housing to remove the top. ... Vacuums

Hoover wind tunnel vaccuum cleaner i need to know


... Hoover Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0725 seconds