Having problems with your Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum ?

Hoover windtunnel vaccum U6445-900 motor not turning on. I removed the screws and located the contacts inside. There is an on-off switch which seems to be stuck Is there a way to replace this switch

Answers :

There are a number of Hoover vacuums that are subject to a recall due to an overheating on/off switch. Check out this web site to see if your is included. You'll need the model number and serial number from the back of the unit. The manufacturer will direct you to an authorized repair center for a free replacement of the defective switch.
I believe that is a fairly new model like 2 to 3 years old.if so on the back where the cord hanger is there are 2 screws take them out,then on the back of the handle there are 2 screws take them out.the handle should slide out towards the back.you can buy the revised switch already in the handle for $28.00.no wiring involved it plugs itself in when you put the handle back on
Repair Help & Product Troubleshooting for Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover windtunnel vaccum U6445-900 motor not turning on. I removed the screws and located the contacts inside. There is an on-off switch which seems to be stuck Is there a way to replace this switch

There are a number of Hoover vacuums that are subject to a recall due to an overheating on/off switch. Check out this web site to see if your is included. You'll need the model number and serial number from the back of the unit. The manufacturer w ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

How to disassemble the brush to empty anything that might be stuck inside of the brush? The motor seems to be overheating, all belts have been checked, all airways are clear and the filter is clean. The vacuum is vibrating and releasing a burning smell, but still sucking up dirt. There is nothing stuck on the outside of the brush, but is there a way to check inside of it to see if that is where a clog is occuring?

If there's a burning smell and the belts are fine, the problem is going to be hot wires causing the insulation to melt, or the motor going bad. Discontinue use and have it checked at a repair shop. ... Bissell 6594 PowerForce Bagless Upright Vacuum

I have an Easy-Flo central vac unit. The handle on the electric hose has a switch on the handle. With the switch on ''O'' in the center, it's off. On the left, is the ''I'' position. The vacuum runs but the power brush doesn't. On the right is the ''II'' position. The switch won't flip that way. It feels stuck. It feels as if there is something underneath of it that won't let it push that direction. I have the switch out of the handle, but I can't seem to get the actual black casing around the

Switches are not usually designed to be dissembled.I would strongly suggest that you dont take the switch apart. you are better off getting a new one. then if you feel like it you can take the old switch apart and if it dosnt work you still hav ... Vacuums

The vacuum is making a noise like something is stuck when it is in the carpet position but not when in the floor position. I can't find anything that is stuck in the areas that I can see. I have cleaned the brush but it does not seem to want to turn. Does this machine need to be oiled so the roller will turn? Is there a way to check inside the motor? Do you think that because the brush won't turn that is making the noise? Do you know of any repair shops in the Lake Havasu City, Arizona area?

As far as the roller brush goes, yes, it does need to be cleaned. Follow the directions to remove it and clean as best you can of all debris. On both ends of the roller brush there will be two "holders" of sort that connect the brush to the frame o ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The power cord is stuck part way out - it seems to have slipped over the edge of the reel inside the machine, so it won't pull out and it won't retract. Pulling hard does no good.

Hello,Yes, pulling hard is not a good idea. You need to use techniques to get it out.Get a flat Phillips screw driver, use it to bring it out. Or use a screw drive to disassemble the part that that went inside the machine. If ... Vacuums

The switch on our Hoover Windtunnel vacuum cleaner is not working. I have located the replacement part on your website...part#Ho-28161067, I've removed the wires from the switch. Is there any trick to actually removing and replacing the switch itself? It seems to be in there rather tight.

No, follow the directions to replacing the switch and you should be good. if you got the kit then splice the wires and replace them with the wires profied and the wire nuts, you should be good. ... Vacuums

My electrolux ambassador power wand quit working. I replaced the switch that shuts it off when the roller stops, but it wasn't the problem. The on/off switch is fine, the motor is fine. We have traced the problem to the wires inside the canister by opening the inside cover to the bag container. We see the power cords going into the canister but we're not able to get to anything. We can't find any screws to undo that would open it up in order to follow the wires deep into the canister. We've bypa

... Electrolux Vacuums

The last time the vacuum cleaner was used the outlet sparked causing it to smoke when turning on vacuum cleaner. I replaced the outlet and plugged it in and things seemed o.k. Today I turned on the vacuum, it stayed on for a mili second and went off. I checked the switch on the vacuum and it showed voltage coming and going, but would not turn on again. I checked all the wires in the area of the switch all seemed o.k. I thought maybe there might be a short in the cord. When I went to plug

... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum

On-off switch My problem is finding a source for an on-off switch for an electrolux vacuum sweeper model 2100. I have replaced the broken toggle and now the sweeper turns on but only as long as the outside button is depressed. It appears that the on-off switch itself is broken as the switch does not ''hold'' when the toggle is activated. It seems to return to it's ''off'' setting as soon as the toggle is released. What ''holds'' the switch in its ''on'' position? Does it depend only on the on-

Hi Hugh. The 2100 has a rocker switch under neath the button. it is probably broken, or the button has a worn detent spring. If you would like, I could send you a switch kit with the rocker, button, and detent spring enclosed for around 20 dollars ... Vacuums

I have a Hoover Elite Rewind model #uh71009. We moved recently and it was jostled around and the red power switch popped out. I put it back in but it's stuck; it stays either left or right, it doesnt move back and forth. It appears there may be another piece missing from the power switch...all I have is the red switch and a tiny cylindrical metal tube with a spring on one end. This piece fits into the hole on the red switch. Inside the vacuum itself where this goes, there is quite a large cavity

... Vacuums

I need to purchase new blades for our 52" Jericho IV ceiling fan, Model 166315. I went to home depot in Harrisville, UT and they said that we would have to contact you and they didn't have ANY replacement fan blades in stock. HOW COULD THAT BE WHEN THEY HAVE HAMPTON BAY FANS ALL OVER THEIR LIGHTING SECTION? What kind of a business are you running when one can't get replacement parts? Our fan is making noise and I want to replace the blades. How hard can that be? By-the- way; I hope you no

... Vacuums

Henry will switch on and stay on, only while the switch is pressed.rnHow can you get at the switch to replace it? There seem to be many crosshead screws under the motor part,- which need to be undone? Thank you.

Sweeper shop to get switch, you could have a wiring problem . Take casing off and check out and get those screws out of there they could cause some damage all while unplugged of course.bare wire coud cause your problem and thoe screws hopefully arent ... Numatic Henry Bagged Canister Vacuum

Unit has power from Plug to unit. Current flows all the way to switch and switch seems to be ok but unit will not turn on. Wife says it was cutting on and off when moving it around. Checked conntec

You either have a bad switch oir you have a short in the cord.plug it in and turn it on then move the cord around from top to bottom and see if it acts up..if not tap on the switch afew times and if it cuts out then the switch is bad.try to plug it i ... Vacuums

I have the new power on/off switch to replace the old one(Rainbow vacuum). However the new switch has 4 contacts & the old one has 6. Need wiring diagram.

Simply pair 1 each of the power head leads and motor leads on to one terminal and wire the cord as on previous switch. ... Rainbow E series Canister Wet/Dry Vacuum

Is there any way to repair or replace the belt GUIDE on the inside of the belt compartment of a '97 Hoover Wind Tunnel (not self-propelled)? It became twisted when a belt broke and now the belt rubs against it and sounds really weird, and I'm sure new belts will continue to break.. This guide is a long piece of molded material (part of the compartent wall) to keep the belt from coming off the pulley. It also had a sort of metal clip on it. It was loose and I took it off because of the way the pa

Honestly you should take it to a vac.shop they can fix any vac. ... Windsor SR12 Sensor Bagged Upright Vacuum

Is it common for the switch to go bad on a rainbow e series? Replaced cord but switch seems to be bad.

Not that common but more common than the cord unless a pet chews the cord or it gets stretched tight and breaks at the plug. ... Rainbow E series Canister Wet/Dry Vacuum

The water dispenser must have been left plugged in and the hot water switch on without any water bottle on the unit because a plastic part inside got warped and now the unit tries to heat the whole 5 gallon jug of water. I want to replace the inside plastic part but I don't have the manual and don't know which part no. to request or where to send my request for parts.

Please state the brand and model number of your water dispenser, so I could give you the exact part and lead you where to purchase it.Post back ... Vacuums

I replaced a Intermatic light timer with a GE 15086 timer. I have read several solution, but none fit my wire sceme. This is hooked up as a 3-way switch so the second switch can turn outside lights on manually. Here is what I have; Four timer wires: R B W G Wall outlet: B, B & R (Two), G, W bundle What ties in together to make it all work?

1) GE 15086 is not a 3-way timer.GE programmable timers are for single-pole switch replacement only. I have tested this timer, and own several GE timers, and many other brands.2) Open following link to identify timers that work for ... Vacuums

My bissell proheat upright steam cleaner is spraying out through the attachments just fine, but will not spray to the floor when using upright. we've taken it apart to find that there is no water at all going through one of the hoses, but it appears the hose is connected behind the on/off and heat switches, we can't seem to figure out how to get in there to replace that hose....any suggestions on how to access this?? just curious how you would get in to replace the hose, we know it is the hose..

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Brushes stopped The brushes stopped turning while using the cleaner. I removed the brushes to see if the spindle was broken, it wasn't. I then removed the top plastic cover and checked the switch that engages the brushes; it didn't seem to be moving correctly. There's one spring on the switch - should there be two? Or do you think something has broken on the inside? Thanks for any help

Most likely the turbine is bad, it may just be clogged up, you can take it apart and clean it out real good. That may work, but it may not. Sometimes it is best to replace the turbine. ... Hoover F7431-900 SteamVac Vacuum

How do I clean the inside of the cyclone in my DC28 Dyson? It has alot of built up dust on the inside, it seems like there should be a way of getting it out...? Thanks, Veronica

... Dyson DC28 Animal Bagless Upright Vacuum

Am attempting to get 'inside' the vacuum to troubleshoot why it suddenly stopped running. Suspect it may electrical, and have already checked the obvious (visible cord and plug.) However, there doesn't seem to be an obvious way to get inside the canister without destroying something. Thanks!

Hi There,\015\012\015\012Here's a link to a repair solution that I've done explaining how to diagnosis the cord reel, and open up the machine. The model this is done on is not the same exact model as yours, but the repair will be almost ... Miele S251 Flamenco II Bagged Canister Vacuum

Dirt devil vacuum cleaner--trouble vacuuming dirt and pet hair on carpeting --is the problem with the spinning brush which contacts the floor,  not contacting the carpeting??  I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting.  Sometimes, it seems like nothing is being vacuumed up --unless I have just put a new bag on the vacuum... Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums

Try replacing the belt. Rubber belts stretch out after about a year. ... Dirt Devil CE6100 Featherlite Upright Vacuum

U5468-900 handle on/off switch no longer works. Switch on main body works fine. Seems like handle assembly has worn out. Can I get a replacement?

... Hoover U5468-900 WindTunnel Bagged Upright Vacuum

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a

... Bissell ProHeat Deep Cleaner Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0765 seconds