Having problems with your Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum ?

Hoover U6433-900 brush turns intermittently - Belts are in tact but the lower thin one seems loose. How often do they need to be replaced?

Answers :

The rollers on each ends get tangled with hair etc...
\015\012causes resistance. Give it a good clean up.
Repair Help & Product Troubleshooting for Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover U6433-900 brush turns intermittently - Belts are in tact but the lower thin one seems loose. How often do they need to be replaced?

The rollers on each ends get tangled with hair etc...\015\012causes resistance. Give it a good clean up. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Foot latch is broken. need to replace with new one. how does one access to remove the foot pedal latch. By foot latch, I mean the foot lever that releases the upright to lower the handle and begin vacuuming.

It is accessed from the bottom underneath by the rear wheel. However, If there are and cracks on the pedal release socket area then the base will need replacement. parts are little cost but the unit needs to be completely disassembled. ... Hoover U6446-900 WindTunnel Bagged Upright Vacuum

I need to replace the brushbaron my DC17 Animal model Dyson. It's almost four years old. I can't find the correct part number on the Dyson Website and I can't seem to find a Dyson repair center in Albuquerque, NM. What are my alternatives? If I can't service this machine without returning it to Dyson, I won't ever buy another one.

Hi,\015\012\015\012The original Dyson part number for the brush bar (often called brush roll) is: 911961-01\015\012\015\012If you type the above part number into Google Products (click link below) you will get a list of suppli ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I need to replace the cord on an older Hoover upright, model S660, about 1986 vintage. The cord broke where it enters handle. Handle comes apart easily. Just not sure how to pop the switch out without breaking it. Was looking for a manual online to see parts diagram and/or instruction on disassembly and cant seem to find one for that old of vacuum.

Check ebay. those vacuums are worth fixing. I loved them. they would **** the carpet off of the floor! those cords aren't hard to replace.just remember the way you got the old one out. ... Vacuums

Our problem with our Rainbow E Series is that it has sucked water up and blown it out through the lower part of the hepa filter, making the filter wet and dirty. This had happened before and the repair shop did not see any problems with the machine, so we replaced the filter and were very carful not to overfill the tank and to change the water often. Now it has happened again and ruined another filter. Do you know what could be causing this issue? Can the filter be cleaned or will a new one be

Thank you for allowing\012us to help, please respond with further questions and concerns\012\012Spanish speaking\012available for all problems\012\012 ... Rainbow E series Canister Wet/Dry Vacuum

I have cleaned the filters on my dust buster. The vacuum works for a minute then the battery seems to wear out and the power weakens until it stops. How do I replace the battery on this vacuum? Do I need just one 9.6V battery? What screws do I loosen to insert the battery? I can't find my instruction booklet. Tank you for your help.

... Black & Decker 15.6 Volt DustBuster Vacuum

The brush won't roll so i guess i need a new belt. the one there is intact but seems loose. Any other suggestions? Thx. Lynn eureka the Boss Model 405 and type B1.

... Eureka Boss SuperLite Bagless Upright Vacuum, 405AVacuum

My morphy richards premair 1800W has suddenly lost suction. I suspect there's a hole somewhere in the hose, and I need to replace it - but no-one seems to have the parts. does anyone out there have a solution

... Morphy Richards Vacuums

The power wand electrical connection on the power unit itself seems to be corroded. I think I need a new two wire plug to plug into the wand. the model is a Eureka 6984 A. I am able to disassemble the power unit if necessary and replace the wire and plug if one is available

Try hesco inc they have a on line store with all the vacs parts diagrams and fast shipping. ... Eureka Vacuums

Need a replacement on/off switch for Dirt Devil Deluxe Model 8201 (more than 12 years old). We have the old one out. We just need a new one to replace it. Where can we get one?

... Dirt Devil Vacuums

I need please a belt for the brushes the larger one but may be better to replace the smaller one as well. I can see how to replace the small one very easily but not sure how to get the new one onto the end of the big sprocket. Please can you help I have the vac disassembled ok just waiting to get the belt to reassemble it. thank you Colin White SEBO AUTOMATIX X1

As you know, there are two belts - the pulley device between the motor and the brush roller is the sensor that measures the drag on the brushes and operates the automatic height adjuster to maintain constant drag. To the left of that double pul ... Sebo Automatic X1 Bagged Upright Vacuum

Hoover Wind Tunnel U6458-900 Self Propel doesn't work - via other expert advice here for other models of Hoover - I'm thinking it is the actuator that needs to be replaced as I can see the cable does not connect to anything on the bottom. My problem is - I can't get the cover off. Been trying for a couple of hours. I removed every screw I can seem to find but something is hold it down. I also am wondering if/when I do eventually get the cover off, would I need to replace the cable when I replac

On some models there are hook/springs that hold the cover of the base snug. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?

Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Pls Help! My Dyson DC05 (Yellow) needs a new wand. Am unsure whether it is the assembly wand or hand one found in spare parts. The wand I need to replace connects the two long hoses together, and NOT the wand which fits onto pickup head. M.thks if you can advise which one I need. Getty rather dusty in my pad!!

... Dyson DC05 Bagless Canister Cyclonic Vacuum

I think I need to replace the main battery in my small floor vac - the one that can be hand held like a dust buster or work like a small floor vac. I need to know how to remove the battery and replace it with what kind of new battery..

I see my sense of humor is not appreciated...it was only a joke. Anyway, here is what you do: First, slide the battery cover off the bottom of the hand held unit. Remove the battery from the motor housing by pressing the tab on connector “A&rdq ... Vacuums

Dyson DC07 I actually need to locate and replace the brush as it split on one end. Looks like I need to pull the belt off to do that. Might as well replace the belt while I'm at it.

Hi.\015\012\015\012Depending on wether your machine has A clutch fitted will decide how easy this job will be.\015\012\015\012The non clutched model is very simple turn the 3 plastic screws on sole plate to unlock position lif ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I need to change out the short hose on the underside of my older Dyson DC 07 Animal (Light Purple). It is the one less than a foot long on the underside which is attached on one end to the main body of the vacuum(I was able to remove this one) and the top of the upper soleplate. The latter one seems to be glued or otherwise permanently attached.Any assistance you could give me on this would be greatly appreciated....Thanks

Hello Cynthia,\015\012\015\012It's not glued, but it can be a little difficult to remove. You need to twist and pull at the same time and it should pull off. If it's being stubborn, squirt a little bit of WD40 / penetrating fluid where th ... Vacuums

Replacement wheel I broke the wheel on my bissell upright model 3760 and need a replacement wheel and possibly an associated side molding. I can't seem to find replacement parts such as these- any suggestions?

The rear number is 2036627, there is no side casing, you would have to replace the whole back, which Bissell isn't making avaiable. But o get the wheel, you might try bissell.com and see if you can order direct, or try a local repair shop to see if ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Don't have one, need access to one, can't seem to find one online

Ebay... ... Vacuums

I replaced the belt in our Eureka Boss Smart Vac, it still seems loose, it uses a type R belt. The beater belt still doesn't seem to turn properly and seems that it doesn't pick up very well when I use it on my berber carpet. We have 2 dogs and I like to use it frequently. I have changed the bags and belt......

Check to see that the beater brush is not frozen up. Pull the brush and clean it, spraying some WD40 on each end piece that holds the brush in place.\015\012Also be sure the belt is properly installed so that the brush turns in the correct direction ... Eureka Vacuums

I need to purchase new blades for our 52" Jericho IV ceiling fan, Model 166315. I went to home depot in Harrisville, UT and they said that we would have to contact you and they didn't have ANY replacement fan blades in stock. HOW COULD THAT BE WHEN THEY HAVE HAMPTON BAY FANS ALL OVER THEIR LIGHTING SECTION? What kind of a business are you running when one can't get replacement parts? Our fan is making noise and I want to replace the blades. How hard can that be? By-the- way; I hope you no

... Vacuums

One of my Levolor double-honeycomb blinds is no longer level (one side goes up faster than the other). Another of my blinds (same brand, model) seems to have broken, with one side no longer rising. Both blinds are about 9 years old. Is there any way to fix them? Or, does it make more economic sense to replace them? Thank you!

Hello,\015\012\015\012This problem is a common problem on this device, there are many people\015\012who are searching for the answer on what to do and what are the causes\015\012of this problem. The answer to this is still not clear. ... Vacuums

Dyson DC07 The plastic pre filter catch snapped on my Dyson. I have a replacement already, but can't figure out how to remove the bottom of the broken one. It looks easy enough to slide/snap the new one in but accessing the old one isn't easy. What do I need to do to get it out?

Turn your dyson over so you can get to the bottom undo the screw and then you can see the bottom of the clip a gentle tap with with a screw driver blade will knock it out and the other one slips in ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Need to replace lower handle and pivot as it broke off. I got replacement but no instructions how to replace.

... Vacuums

Hoover Wind Tunnel 7500 Brush not Turning. I have replaced the Brush and the belt. The problem does not seem to be either to me. I believe might be a missing part. The place were the belt hooks on is a metal pole which never seems to grip the belt well. In fact it seems loose most of the time and slips on the brush, causing the belt to eventually burn up. Could there be a missing plastic or rubber piece meant to hold the belt taught  on the metal pole?

Check the Idler Pulley part Number 43241004 (Item 13 in the IPB) ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0760 seconds