Having problems with your Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum ?

Handle won't release

\015 U6436900 replaced belt and now handle won't release. Didn't touch anything that should have affected this, did I?\015

Answers :

There is a pully that comes down into place and puts tension on the belt when you lean the handle back. I've seen people try to put the V-belt underneath this pully or around it somehow. This causes the pully to break at times and jam up the handle release. This is the only thing you could have brolken to cause this. (other than just a stroke of bad luck and the handle release lever brolke @ same time)
\015\012
\015\012Take the bottom plate off, and try to actuate the handle if the pully is tangled in the belt somehow this would be your problem. In this case remove the belts and re-install them (vbelt should feel way too loose) If the pully will not travel it is more than likely brolken. This is a complex setup with the powerdrive and it has to be perfect for the machine to work correctly. Since it can be very difficult, were the Pully assembly is brolken i would advise you to take the machine to a Hoover authorized service center for repairs. You can find service centers with their dealer locator on their website.
\015\012
\015\012Best of Luck!
\015\012
Repair Help & Product Troubleshooting for Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dyson dc17 hose will not come out/ handle wont release from machine. i've pulled the metal rod up all the way and the handle still won't come away from the machine so i can't use the hose and attachments. anyone know what the problem might be?


Hi there, it is possible that you have a blockage in the wand/hose assembly which is making this difficult to remove. If you are able to remove it to check for this, please contact our Helpline on 1866MYDYSON so that one of our advisors c ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Hi, my Vax rapide ultra 2 shampooer wont stop release shampoo/fluid without use of the trigger on handle?


... VAX Appliances Vacuums

Vax carpet shampooer wont release shampoo


If you unscrew a bit on the base that allows you to take off the brush, you will see a black plastic strip with very small holes in it. These are where your shampoo comes out of. Take a needle and re-pierce these holes and it should work again. I hav ... VAX Appliances Vacuums

I have a Kenmore vacuum cleaner model #116.34720. The problem I am having is that if you are rolling the vacuum around, the base will drop without pressing on the handle release pedal. This often results in a bunch of dirt being dumped back out. The manual doesn't show anything about adjusting the handle release pedal so it holds the handle and base in an upright position better. Any help is greatly appreciated! Thanks in advance!


... Vacuums

The handle release pedal wasn't allowing the handle to lower. I took off the pedal and saw the spring load part was broken. What is this part and how to replace it? Bissell 3760-3 handle release


Our vacuum recently had an issue with it's motor, we had to borrow a neighbors a couple times while we were trying to figure out what to do. We decided to take it to a place that specializes in cleaning supplies and cleaning tools to see if they had ... Vacuums

Handle release how do I fix the handle release? It is not in the correct position. It has come out of the unit part way and will not latch the handle in place.


... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Handle release has stuck down and want release handle


Http://canada.bissell.com/FAQs_and_Answers.aspx go to web and see all information, video, troubleshooting, questions, and fix it.God bless you ... Vacuums

The wand release button has broken. Therefore, the wand does not lock into place which results in swivelling of the handle and sometimes the handle coming off while using the vacuum cleaner. Can this wand release be readily repaired?


... Euro-Pro NV31 Infinity Vacuum

Water seems not being introduced to heating element,which is hot, Depressing the handle appears not to be releasing water from tank; very little if any steam or water comes out base even after holding the handle down for a prolonged period and or pumping the handle.


Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

I broke the handle part of the shark steamer #53101. I don't have the book to try to tell you the parts I need. Can you send me a picture or a copy of the steamer. It is purple. The above number may not be the correct one. It is broken in the center part. It has a little small circular piece that joins the two pieces which are broken. The beginning of the handle at the bottom of the steamer and the next session which has the steam release. The top of the handle is okay . It the middle and bottom


Hi,Ann there are very few parts for these...Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

I have a Bissell Proheat 2x cleaner which has worked perfectly on every occasion. Today I filled the machine as usual with water and formula and switched on, the motor ran, the lights were on and the brushes rotated but upon pressing the spray trigger no water or formula was released. I have cleaned the jets underneath and also followed instructions to release any airlock. It still wont release the water/formula. What else can I do? Thanks Charles


Please check the following with liquid in both tanks.\015\012 \015\012- Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.\015\012- ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bissell 3595 handle release pedal spring(?) missing


I just fixed this on my Bissell PowerForce model #6594 vacuum myself. Woo Hoo for me. :-)\015\012\015\012I called the local vacuum repair guy and he told me he'd repair it for me if I insisted but that since my machine only cost about $80 ... Bissell 3522 PowerForce Bagged Upright Vacuum

Whispertone powerhead handle release replacement


Take a butter knife and/or flat head screwdriver and press forward on the four tabs that retain the pedal. ... Kenmore 23313 Whispertone Bagged Canister Vacuum

Hoover floormate handle release pedal broken. Need diy repair information.


... Hoover Vacuums

Broken handle release


Most times they don't break, it is the 2 screw holes at the back that back and the top will raise up from the base. If this is the case, remove the 2 screws and install longer ones with a flat washer on them to fashen down the top. But first the to ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Handle release stuck


Its as simple as pulling top casing of bottom part of vac off and replacing the pedal just pay attention to where the springs go as you take them out ... Electrolux EL8502 Versatility Bagless Upright Vacuum

Handle Release Replacement procedure


... Eureka 4874 Bagged Upright Vacuum

Broken handle release spring assembly on an electrolux intensity


... Electrolux EL5020 Vacuum

High pitched screeching/broken handle release


For the handle problem, detent lever part #2030052 and costs $4 to $5. A bearing in the motor is what is making it sound bad, part #2032211 and will cost around $60. You could try bissell.com or call them. They can at least let you know who has Bi ... Bissell CleanView 3596 Bagless Upright Vacuum

My shampooer will not release water when i push the release button on the handle


\015\012\015\012\011\011\011\011\011\015\012\015\012\011\011\011\011\011\011\015\012xpinto ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Dyson 28 handle is stuck in the locked and upright position. Vac runs fine, just can't get the handle to release to run the vac


How do you remove the air duct (plastic sliding piece) that is making the vacuum stay in locked upright p[position? ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?


... Vacuums

The handle release button is broken/ the handle will not fold


If you go to this URL:\015\012\015\012http://www.ereplacementparts.com/eureka-2590a-carpet-cleaner-parts-c-108750_109432_109471.html\015\012\015\012you should be able to identify the part and order it as well.\015\012\015\012If you ... Eureka Atlantis 2590A Wet/Dry Vacuum

My eureka 5902 4D bagless uprights roller brush stopped spinning. The belt is ok. This model has a sliding switch for roller speed. The brush should spin when you release the handle via the foot release. Bad brush motor or is there a fuse involved?


The same thing happened to me about a year ago with this very model. \015\012The issue on mine was a small, copper-colored metal wheel that attaches to the end of the brush roller. You'll need to remove the top cover (there are several screws). ... Eureka Smartvac 4870 Bagged Upright Vacuum

Chassis hook broken to rod which controls release of liquid shampoo in Hoover steam cleaner. It is the back of the handle area that is snapped off, not the actual rod with "push on / release"


If it is part of the handle, it breaks inside alot, part number 39458006. #2 in the picture.\015\012 \015\012 ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0367 seconds