Having problems with your Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum ?

I have a Hoover Anniversary Special Edition and the Power Brush stays in the Off position. What am I doing wrong. It will not go into the "on" position. I have changed the floor surfaces and still it does not come on?


Answers :

Hi,

Have you checked the Brush On/Off switch?

If you find that switch is not working :-

Order it at :-

http://www.govacuum.com/hoovwinonswi.html

Also, Try to adjust the position of the brush. Sometimes, it might work.

Hope i helped you.

Thanks for using "Fixya".
Repair Help & Product Troubleshooting for Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Hoover Anniversary Special Edition and the Power Brush stays in the Off position. What am I doing wrong. It will not go into the "on" position. I have changed the floor surfaces and still it does not come on?


Hi,Have you checked the Brush On/Off switch?If you find that switch is not working :-Order it at :-http://www.govacuum.com/hoovwinonswi.htmlAlso, Try to adjust the position of the brush. Som ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I opened the cannister to change the bag and when I closed it the motor switch will not turn on. The second position which turns on the attachment for rugs still comes on. We thougth it was the switch so we ordered the part and it is still doing the same thing. Is there a reset button somewhere inside? The only reset button I see is on the attachment which is working.


It can be a few things. First check the overload protector located on top of the canister. If it has tripped the unit will not run. Push it in to reset. \015\012If that is the problem check the motor safety filter to see if it is clogged and caused t ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Electrical problem The light comes on but the motor will not come on when the on button is pressed. Is there a reset button? I thought it was because the bag was full but I just changed the bag and the motor still will not come on.


The light is separate from motor. No reset switch. Check for a fuse but i suspect it may be brushes are worn out and not making contact.Sometimes that starts as an intermittent.Hopefully one of the coils isn't open circuited. ... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum

Just got my dc33... one issue... the dial switch to control btn bare floor / carpet mode doesn't seem holding in it's position when I set to the bare floor mode... it keeps coming back to carpet mode with brush-bar activated... the dial doesn't really click to the floor mode. Any advice on this?


Hi there,I'm sorry to hear you're having difficulties with your DC33. If you're concerned that the brush control doesn't seem to be staying in position, it's probably best if you get in touch with us directly. One of our experts will be h ... Dyson DC33 Bagged Upright Vacuum

I have an electrolux renaisence vacuum. the brush in the floor attachment turns but I have no suction. When I change to bare floor option on the handle the brush stops turning (correct) but I still have no suction. The lights on the handle showing --floor,carpet, high and low all work.


Sounds like you have a clog, either in the hose or the inlet by the brush roll. ... Vacuums

There is a rubber valve on the top of Dyson DC14 all floors. When the vacum is locked in its upright position or the hand wand is used there is a whistling sound coming out of the valve. When the vac is used as a floor vac, it does not make the sound. Is this something that I can fix? Is there an obstruction somewhere that would be causing this sound? thank you.


The Fixya user in this repair is giving out personal contact information rather then helping the customer out on the Fixya board. This defeats the whole purpose of Fixya if the "TheDysonTeam" just gives out his phone number and helps the customer o ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Bag full indication comes on; changed bag; still wont run.


Turn the knob on the top of the vacuum all the way to the right and try it again ... Electrolux UltraLux 2000 Bagged Canister Vacuum

I have a Hoover WindTunnel Bagless Vacuum Cleaner, Model #U5753-900, Serial number 110600215585, which I purchased from Loew's on 3/31/07. With it, came a Hoove Slider for hard floor surfaces, Model #S2105, Serial number 050500084989. The Slider strted making a noise--I thought something had been caught in the roller, but discovered, it had not; so I and my husband proceeded to take the Slider apart. I believe one of the belts had come off; but when we took the screws off the bottom to check


... Vacuums

I've got a Kenmore canister vacuum, Progressive 236123, and there's a burning smell from the belt side of the head--smells a lot like hot rubber. I've cleaned the agitator and changed the belt, but I still get the smell. It's stronger when I'm using "carpet" mode than when I'm using "bare floor" mode. Any ideas what the problem is?


... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

I dropped my battery operated alarm clock: the second hand still works but the alarm doesn't come on at the set time and the hour & minute hands don't "hold" their position - I took the clear front off and discovered that I could move the hands to a more secure place on the center spindle but I discovered during the night that the correct time was no longer showing. I really like this clock b/c it's battery operated and I can hear the alarm (when it worked) plus it has a "night vision" dial tha


The hour and minute hands can be pushed onto their respective shafts at any point in most clocks.\012If you already know the time that the alarm is set, let the clock run until it sounds. \012When the alarm sounds, install the hour hand a ... Vacuums

My Kenmore Elegance Canister Vacuum powers up but has no suction. Tried changing the bag and cleaning the hose. Still the performance indicator light comes on. Now what?


... Kenmore Vacuums

I have a power drive baggless vacuum cleaner...it runs well, but suddenly it seems to have lost most of the suction coming through the hose and floor area. When I remove the dirt container, the suction below it seems strong. I have had it to repair twice--they have tuned it up and replaced all filters and belt. It still does not pick up well when I vacuum or use the hose. Can you help ?


There is something stopping it up,you will have to dissasemble the unit to find the blockage,this is the most likely problem. ... Hoover U6660-900 WindTunnel Bagless Upright Vacuum

The roll brush will not turn when on floor. Too much pressure stops brush. Changed belts and still not working


Turn the belt inside out. This problem stems from a design flaw in the mechanism that turns the hoover from bare floor to carpet. After taking it apart I realized that the spring that pushes the belt tight (to make roller spin) is not any where nea ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

Hello, I have the same model. And though it is three years old, starting from the last month, it does not clean anything anymore. Cannot even pick up one single thing from the floor. Every dirt gets stuck in the hose. I cleaned the hose and cleaned the filters but it still does not pick anything up. Is three years its normal lifetime or do I have the change the filters, instead of cleaning them? Thanks.


I know bissell vacuums are very cheap but they should last more than 3 years. there should be two parts to the dirt cup. remove the dirt cup and above it there should be a round plastic part. unscrew it and check that filter. ... Bissell 6594 PowerForce Bagless Upright Vacuum

Put in new clutch, but the brush does not seem to be lowering when you change between bare floor and carpet. Does not seem to be touching carpet when engaged. Still has good suction.


The brushroll must be broken ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

The brushed on my steamvac Dual V F7227 are no longer working. We have pulled and cleaned the brushes, and the filter, but the brushes still will not come on. I saw a reply to one person that it is the belt. If so... how do I change it?


Greetings from GoVacuum,The Hoover SteamVac's are notorious for this exact problem. There are several things that can be causing this probelm.First, what you'll need to do is take the brush block out of the machine. To do this ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

No suction i have a bissell lift off revolution vacuum. I have cleaned all the filters and emptied out the canister made sure that the hoses are not plugged but it will not pick up unless you use the hose. the floor brush is clean and still no suction coming from under the vacuum... could you help me please


Is there a blockage in the small hose in the bottom of the machine \015\012take of the pod and you will see the small hose, \015\012Is the main hose pushed into the bottom housing ... Bissell 37603 Upright Vacuum

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I


Search for bissell pro heat pump. bissell.com will not have it ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I


Pump part number is 2107181, the diverter valve # 2136988. You can Bissell and they can tell you who may have parts near you, or you maybe able to order thru Bissell.com. Before you took it apart, were you getting water to spray out of the hose. I ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Changed e bag on Electrolux canister vacuum and indicator light still comes on...


... Electrolux Vacuums

My vacuum over heated, the warning light has come on a the filters changed but it still refuses to reset and turn back on, any suggestions?


Could be fuse line! Estimated cost of repair $39-59.00 with 1yr warranty\015\012\015\012Shipped USPS is very cheap and with our service it still beats many!!!! ... Miele Cat & Dog 326i Bagged Canister Vacuum

I have a bissell proheat multi surface 2x model 9200-T 08296C. It stopped spitting the water and soap out on the floor, but still sucks from the base and hose. I took it apart to see if anything was disconnected but saw nothing. Please help!


I Had the same problem with my model 79011...take the upright handle apart & you will see a pot-metal rectangular box midway down the lower section of the handle with wires on it & 2 hoses attached. This is the water heater unit. LET IT COOL ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I plug my Polti in and absolutely nothing happens, no lights come on nothing, I've changed the fuse but still noting


There maybe a broken switch or the motor may be burnt out. Take it to a used vacuum store and they will give you sound advice. ... Polti Eco Pro 3000 Canister Steam Vacuum

I have a eureka surface max 300, i saw smoke come out of my vacuum i seen that the belt was broke every time i change belt i run it on it snaps every time ive put 3 new ones and each one break right when i start it it looks like the metal piece is burning it is there a piece missing?? what am i doing wrong?? ugh i just purchased it couple of months agoo not even older then 6 months .. what do i do?


... Eureka Capture Upright Vacuum Vacuum

Problem with electrolux z370a.Plugged in pressed start switch no lights come on,changed fuse still no lights but heater and temp gauge is working


Hi, try to determine if the power source is working properly if the Electrolux will not turn on, Make sure it has not come unplugged and that you do not have a blown household fuse. If necessary, reset the circuit breaker to regain power to the outle ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0901 seconds