Having problems with your Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum ?

Cover knobs How do you remove the two plastic knobs on the cover for bare or carpet and carpet heighth to get the cover off?

Answers :

You don't have to remove those knobs to get the cover off. Just 2 screws from the bottom, then on each side you will notice a slot from the bottom, use a screwdriver, insert in the slot, and pry out to release the catches and the top cover will come off.
Repair Help & Product Troubleshooting for Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Cover knobs How do you remove the two plastic knobs on the cover for bare or carpet and carpet heighth to get the cover off?

You don't have to remove those knobs to get the cover off. Just 2 screws from the bottom, then on each side you will notice a slot from the bottom, use a screwdriver, insert in the slot, and pry out to release the catches and the top cover will come ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Kenmore Model 116 Cannister Vacuum.Trying to get into motor area. Think belt is worn out. I have removed the front two screws under the hinged cover, but can not remove cover over motor.. Still attached at rear. No evidence of any more screws to remove.

Under the cordwinder actuator button, are your other two screws. To remove this cover, take a flat tipped screwdriver and , very carefully, find the "tabs" (there are two) both on the front section under the button. Then, Carefully, press them in a ... Vacuums

Bissell pro heat carpet cleaner clear cover removal

Just lift it up probably suction holding it ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

My vacuum cleaner is making a loud squealing sound when I turn it on and the brush is turning. It gets louder while vacuuming the carpet. I tried to remove the bottom cover to see inside but, took out a bunch of screws and couldn't get the cover off.

... Kenmore Progressive Direct Drive 30912 Vacuum

I am getting very little suction from the motor. The hose is clear, the bag new. When I open the bag cover, plug the hose in and turn the vacuum on, there is next to no suction from the motor. What do you think is wrong? How do I remove the cord retractor to get to the two screws that hold the back of the canopy cover?

Your problem is probably is you don't have a proper seal in your chasis. A vacuum has to be sealed tight or the air will leak out and the seal broken. Check around the whole body after the bag is in and check for any airflow noise. I could help more ... Vacuums

I need to remove the top cover from a Wertheim w4030, I have removed all screws that I can get at. I have notice a further 3 in places that is not possible to access. It looks as though the two buttons on the top if removed will provide the solution but I don't want to break anything by forcing something that is not supposed to be done. Can you help?

... Vacuums

How to dismantle a Miele S 5980 vacuum cleaner. The RESET switch has fallen in and I can't remove the plastic panel to replace it. Neither can I remove the cleaner body to get in from beneath. I have removed 2 screws from the front of the barrel (nozzle end), one screw centre front, two screws towards rear, but there seems to be something else holding the housing together. [email protected]

... Miele Vacuums

Brushes stopped The brushes stopped turning while using the cleaner. I removed the brushes to see if the spindle was broken, it wasn't. I then removed the top plastic cover and checked the switch that engages the brushes; it didn't seem to be moving correctly. There's one spring on the switch - should there be two? Or do you think something has broken on the inside? Thanks for any help

Most likely the turbine is bad, it may just be clogged up, you can take it apart and clean it out real good. That may work, but it may not. Sometimes it is best to replace the turbine. ... Hoover F7431-900 SteamVac Vacuum

I can't get the plastic steam valve knob off. There is a hex set screw on the stem, inside the machine; I was able to remove that but the knob still won't budge off the stem. Any tips?

... Vacuums

Poor suction...continued Wow, thanks for answering so quickly! To answer your question, yes, there is suction at the screen, but it is very weak. I keep that screen clean. As a side note, I noticed that when I remove the top clear plastic cover (that would be part # 37 on the diagram, as far as I can tell) there is decent suction coming from the intake there--part 36? 30? it's hard to tell. But with the cover on, I feel no suction (from where it sucks up the water directly from the carpet),

Wish I had it in my shop, it is hard to figure your problem. I do know that you must have something out of place and you may have to take it apart to find it. You may feel some suction there at the top of the clear nozzle, but maybe it isn't strong ... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum

I can't find the 4 screws to get to the belt on a dirt devil 22.0 Fx. The bottom of the vaccuum says " remove four screws from bottom of nozzle then lift top nozzle cover off", where are these screws, I can only find two, and which is the top nozzle cover?

... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

Hoover self propelled bagged windtunnel upright model #U6435-900...how do you remove the green plastic shell cover to get to the part that secures the v belt...we need to secure the bolt and cannot get the area. Brushes and transmission wheel not rotating? thanks

Greetings from GoVacuum,\015\012\015\012Here's a great video repair tutorial that we've put together to try and help you with the repair on your Hoover WindTunnel. I hope that this helps you with your repair. If you found this solution ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

We have two of these vacuums and both of them have experienced the same problems. First the floor heighth adjustment doesn't work and now neither one will pick up on either carpet or floor when in the brush/floor mode. They both seem to work with the suction hose function. We have removed the back panel to see if there was an obstruction but it was clear. We have changed the bag and the small filter (not the HEPA filter) all to no avail. What else can we do? We are desperate to use our vacu

Did you check the powerhead for obstructions? With a bend in the tube just below where the hose connects, this is a common spot for clogs. To check, detach hose and drop a coin in the hole. If it doesn't drop through, a blockage is present. Use t ... Electrolux Oxygen 3 Upright Vacuum Cleaner - EL5035 Vacuum

I can't seem to get the belt cover off of my Kenmore Progressive 400. There are two buttons that say above "belt and bulb change" but the buttons do not move. Do you know how I can remove so I can put a new belt on? Thank you!

You have to take off the top of the power nozzel that has the light lense. There are two pressure locks,one on each side. Use a screw driver to release. You will see the screws.Take the two screws out and on some models, there are two pressure locks ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Ultra model HOw do I remove the excess hair/carpet fiber left behind the clear plastic cover that didn't get sucked into the tank?? Mary [email protected]

There are six black screws holding this cover. That's all you need. Good luck. ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

After removing the filter, I cannot get to battery on the Dirt Devil Kone M0213, there are two horizontal screws. Removing them does not help getting to the battery, no way to remove the insert where the battery is located.We have two of these, however they did not come with a manual for dis-assembly. Please help or proved a diagram on how to remove the battery. Many thanks, Wesley Lennon

Sheesh, did anyone actually read the person's question? It's about the battery, not the filter.\015\012\015\012You have to get the outer cover off and it's not easy. There are four tabs which need to be released. I have to use a very sha ... Dirt Devil KONE Hand Vacuum MO213BLU Vacuum

I shipped my brother PE 770 embroidery machine purchased sept of 2010, to a lady who perchased it on ebay. Had used only once. Everything worked fine.I shipped in the original formed styrofoam box. I removed the embroidery arm, releasing the locking plastic hook holdind the machine and the arm together. When to lady removed the machine first in the original plastic shipping bag, two parts fell out. Her photo she emailed showed a black plastic piece with two holes or pivot points.also a silver me

This is a link to the manual for this machine. Do you see a picture in the manual of the parts you are describing? Reply with a part number and I will do my best to help. ... Vacuums

The retracktable power cord on my Panasonic MC-E7103K is jammed inside the machine. Does anyone know how I remove the cover after removing the two visible screws? Brian

... Panasonic Vacuums

I am trying to disassemble a electrolux 2100. I have looked at instructions given by Chemist 1961 and others. On the side, I have removed the rubber covers over the plastic rails but I can't remove the plastic rails that hold the rubber covers on. If I am right, these rails should just slide right out and the outer casing should come part.....or am I doing something wrong. I have pulled and pulled the rails and they don't budge. The rear end won't pop off. Help!

There's a tab at the back of the rail that needs to be released. Turn the vacuum on it's side, slip the tip of a standard screwdrive into the space between the rail and the back of the vacuum, and tap lightly with a hammer. Tap toward the front of ... Electrolux Lux 5500 Canister Vacuum

How to take apart the Hoover U6437-900 to change the belt and clean it. I have the belts and I have removed several screws. It looks like the knobs for the wheel carpet height and carpet to floor selection are the problems but I can not figure out how to remove the knobs. Besides, I am not certain if this is the problem. Do you have the instructions? Thanks

HERE IS THE MANUAL > http://hoover.com/file/500/ ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Agitator belt failed in my Hoover F5853-900 Steam Vacuum Cleaner. But can not remove bottom Cover .. have removed top cover and two screws from the bottom Cover. The smaller Cover is glued to the large Bottom Cover. Need help.

Hello,Unscrew the plate. check if there is any screws at the bottom, if none, exact little pressure to pull out the bottom cover. At this \015\012point you should be able to see the broken drive belt along with the two\015\012 drive bars ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I have a window fan with two fans in it & I cannot get the cover or back off so I can clean it. I* have taken all the screws out that I can get to , but there are two clamps that I can't get off, I'm not sure why the clamps are there but they are on the side with the accordian extention. Please tell me how to get it apart - after 2 years it is really filthy!! Thank you, Janet

Remove all the screws, pry clips off that hold on the extensions, than fan will pull apart. The clips must be pried off. They will not break. Then remove screws holding in the fans and remove them as well. Fairly simple process. ... Vacuums

I havea Bissell ProHeat Model 7901. My problem is that the brush doesn't rotate. I have removed the access cover and both belts and found that the central cylinder for both belts is frozen and will not turn easily. Both belts are fine, except they are now burnt from this cylinder not being able to rotate. What I need is how do I remove the top cover to get at this cylinder to remove it and free it up?

... Bissell 8910 ProHeat Clear View Upright Vacuum

How do you get to the 2 screws under the cord retraction pedal? I can not find any way to remove the pedal. I am trying toi remove the canopy cover in order to get to the motor>

What model is this for? ... Kenmore Vacuums

How do I remove a motor from a Dyson DC04? The bottom plastic cover can be removed by unsrewing the tork screws but the cover beneath the filter won't come off

I can't say exactly how to do this, but when you can't find the screws to take something apart, they are usually hidden by something else. You did good looking under the bottom cover, but what you're looking for is elsewhere. If there is a seam or ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0756 seconds