Having problems with your Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum ?
The brushes are not moving and cannot push forward easily
You will wish to remove the four bottom plate screws, on the corners of the brushroll pocket, remove the agitator bottom plate, and look and see if the two belts are still connected, or broken.
Repair Help & Product Troubleshooting for Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
The brushes are not moving and cannot push forward easily
You will wish to remove the four bottom plate screws, on the corners of the brushroll pocket, remove the agitator bottom plate, and look and see if the two belts are still connected, or broken. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
I have a roomba 530 pet series. It appears that the brushes aren't turning. They are free of dirt and debris and move easily when manually turned. But, You can tell there may not be a motor turning, because the roomba is more quiet than normal when you turn it on. Also, the hair just collects along the bottom of the brush and doesn't get pushed into the bin.
The belt either broke or has come off the track.... this should be easily accessable from the underside of vaccuum ... iRobot Vacuums
The beater bar moves when I push the vaccum forward but it just drags when I pull it back, but when I flip it over to have a look it easily turns both ways. How do I fix this?
The belt is stretched that is why it is doing that. You need to replace the belt. Here is a link to the belt you need and the manual which has instructions: ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum
Brush won't rotate when pushed forward
I had the same problem . The reason it acts like that is due to the cable that runs from the vacuum motor to the brush assembly has an intermittent open. My fix was to find the small cable that was causing my troubles and splice it. Making sure that ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum
Hoover windtunnel U6425-900 the brush roll is not turning. Both belts are in good shape, I cleaned the brush roll and it is free of debris, the setting is on carpet and the brush roll still will not turn. There is a "burning rubber" smell when you attempt to push the vaacum forward a few times. The small belt does not seem to be pulling properly but appears to be in good shape.
... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Hoover Mach 6 U5198-900 vacuum roller brush won't turn. I had opened the bottom to clean hair off the roller. the belts are not broken. When I closed it and turned it on, now the roller brush won't turn. I can push and turn it by hand, but not easily. Then I noticed the brush on/off switch is turned off, but when I step on it, it won't turn on. I was thinking I let something get out of place when I opened the bottom, but can't see what.
... Hoover Tempo Widepath Upright Vacuum - Blue
Model No. D-37272-100 when I have the brushes off the scrubber, they turn very easily, but once I mount them back in place, and turn the scrubber on the brushes won't move But the machine runs in wash and rinse cycle. WHY??
... Hoover Steam Vac Dual V w/ SpinScrub Vacuum
I've had my Dyson DC14 vacuum cleaner now for approximately 9 months and been very happy with my purchase. However, It is used sparingly maybe twice a week at the very most. The problem is when I try to use the item on my carpet, you have to push really hard to get it to move. It's as though the suction power is far to strong. It certainly doesn't glide as I think it should. It still picks up as usual but I cannot imagine that having to 'force' the machine to move is the normal operating procedu
Thanks for your question!I'm sorry that you haven't received an answer yet.The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:1. the question is unclear, incomplete, or poorly ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
My eureka central vac power brush turns off when pushing forward than back on when pushing back. Ever seen this before?
Yes I repair them all the time. What that means is that the connection of the hose handle to the power brush upper wand is loose. This can happen over time with use. The connection just loosens up. Do you have the exact model of the power brush? ... Eureka 1810 Central System Vacuum
Cannot push forward
Sounds like tear down to me to find out whats jamed in the whells ore the belt there not much to fix there things ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum
My roomba 550's side brush cannot move
... iRobot Roomba 550 Vacuum
Bissell Power Steamer Pro Deluxe will not move forward
Tip unit back to lift brushes off floor and roll forward until over carpet edge. tip back unit to sit flush on carpet and unlock handle so it swings freely. now pull backwards ith finger on spray trigger. that's how it works, not by pushing forwad. ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum
Every time i push the steam vac forward it dispenses water
You are having the same problem i am and so far the best solution i have found is i need a new clean tank just got my steamvac today bought it cheap so not complaining much the other solution i found was to only have the cleaning solution tank in for ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
The brush is not moving on the vaccume. I'm pretty sure that the belt is busted. I cannot see how to get the shroud off, so that I can get to the roller and belt. It all looks and feels like one piece, even when I start removing screws. It is a bag-less vac. The model number is - v1310rs. Thank you.
I know on my Eureka I had to remove a couple of screws on the bottom and then get a flat blade screwdriver and wedge it on each side of the base kinda next where the end of the roller would be and it snaps up and off. Really weird I thought but that' ... Euro-Pro Shark Professional Upright Vacuum with Bonus StickVac Red Bagless Vacuum
My Bissell Proheat 12 amps' brush keeps dragging on the carpet when I go to push it forwards. And it releases alot of water.
Mine is doing the exact same thing..Push it forward and it makes a awful noise. The Brush on the bottem is loose and it isnt spinning. SO i took and turned it over and there is a metal gear like part that runs the belt on the brush. I took it out and ... Bissell 8910 ProHeat Clear View Upright Vacuum
We have a Bissell Revolution Lift-Off Turbo 3760-1 and the upright brush is not working/rolling. It only moves when pushing the vacuum. We checked the belt and it seems to be fine. The vacuum works fine as a hand-held. Any suggestions? Thanks!
These belts need to be changed every 6 months regardless of the way they look. ... Vacuums
My Dyson is very difficult to push forward. I've made sure the brush is spinning freely. How do I find out what is causing this and fix it? thank you.
... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
Vax mach 6 brush bar does not spin properly. does not spin at all on lower carpet settings and also when it is being pushed forward
On my Hoover Savvy U8174-900 on carpet setting, the brush spins when I pull the vacuum towards me, but stops when I push it forward. Belt is tight and fine.
Hoover savvys have two very common problems that cause this. The first and most obvious is the belt that you checked already. Many times the belt is tight but those particular belts have teeth and should you lose any teeth on the brushroller OR th ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum
I have a self propelled Royal Dirt Devil vacuum model number 087900 and it goes backward fine but forward has to be pushed so hard it's impossible. Is this a switch? Do you know about how much the part would cost and can it be done by a beginner. We fix a lot of things ourselves but we aren't mechanics by no means. We put a brand new belt on it. I don't think it can be put on backwards and brush turns fine. Where is the switch? Use layman's terms.
You might try a new belt and/or brush roll. The brush roll is what helps pull a vacuum forward, the power drive helps, but if the brush isn't turning like it should, then it will hinder forward motion. The belt may look ok, but they stretch to the ... Vacuums
I can't get the latch that connects to the brush head to engage. Thus the vacumn is extremely hard to push. It has suction, extreme suction. Rollers appear to be dragging. I've tried to remove and reinstall the head several times but cannot seem to get the latch to engage. Please advise.
It sounds like something has come out of it's socket. If the brushroll won't turn rapidly, your clutch is worn out ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
My vacuum goes backwards easily, but forward with GREAT effort..
... Hoover U6446-900 WindTunnel Bagged Upright Vacuum
I have a kenmore sewing machine model 385 1551 6000 serial number 24 231 961. when i push the button to make it reverse, i cannot unreverse it adnd make it go forward.
I bought the 085845 yesterday, put it together and had trouble pushing it on my 8 x10 area carpet. The vacuum did not move easily and seemed to "pick up" the carpet. It seemed that the automatice height adjustment may not have been working. Any suggestions?
I called Dirt Devil and they said return it! ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum
The brushes will not turn when on and cannot move them even manually
Drive belt has most likely broke and jammed inside the power head. Remove the bottom plate on the power head and replace the drive belt. ... Kenmore 25512/ 25513 Progressive Canister Vacuum