Having problems with your Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum ?

Hoover U6439: Belt keeps slipping off

\015 Th belt on my Hoover U6439 slips off almost everytime I use it.\015

Answers :

The belt is stretched and you simply just need to replace it. You can get the belts you need for this model here:

http://www.vacbelts.com/hoover-self-propelled-windtunnel-belt.htm
The belt although not broken has been stretched. You need to replace with a new genuine belt, which will me about 3/4 the size of a stretched one in most cases.
Buy two belts and keep a spare replace every 3-6 months before it slips, for best cleaning results.
Clean the brush roll and motor shaft when installing. Unscrew the brush end caps to remove hair , dirt and thread.

Repair Help & Product Troubleshooting for Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover U6439: Belt keeps slipping off


The belt is stretched and you simply just need to replace it. You can get the belts you need for this model here:http://www.vacbel ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My hoover tind tunnel model 5453-900 series the belt keeps slipping off the agitater brush-what can i do to fix it


Your belt has probobly stretched even though it continues to function. try a new belt assuming the belt path is clear and any guides are properly positioned when the cover is properly replaced and the hump on the brush roll that contacts the belt is ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a Hoover power max self propelled vacuum. The belt that goes to the self propelled part keeps slipping off. I've had the belt replaced, but the problem persists. What can be wrong? I've taken it to a Sew N Vac repair, but all he did was replace the belt again. And it still has the same problem.


I can guess of one problembelt gets removed when motor is running right?am assuming that belt is fit tightly and fits correctly when motor is in restif so then ur motor is not running at a proper speed which can be a pos ... Vacuums

Need help with Hoover S3765-040 WindTunnel Electronic Bagless Canister Vacuum. The belt that rotates the brush keeps slipping off. what to do?


The belt could be stretched and that could be causing the slip. Or you could have the wrong belt if you've replaced it recently ... Vacuums

Windtunnel belt I have a new Hoover Windtunnel canister. The belt keeps coming off. It happened a couple weeks ago (several times after putting the belt back on) so I assumed I might need a new belt as it might have dried out at the store. I ordered new belts and today I used it for about an hour and the belt came off again, twice. There doesn't seem to be anything to hold the belt on the stem as it seems to slip off. I have tried it centered, to the left and to the right....can you help. I am v


I've successfully used a compatible belt - Royal 104425001 .It's still new, but for the time being at least - it works. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

My Miele vacuum cleaner has the red triangle light on and keeps switching on and off. Is it broken? have been hoovering upstairs and I noticed the hoover had the red triangle light on. I changed the hoover bag but it still kept going on and off. Is this an overheating problem or is the hoover on the way out?


... Miele Vacuums

Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest


I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum

Belt slipping Belt slips off and rubs causing burning smell from the belt over heating. Of course this puts an indent into the belt and has to be replaced. How do I keep the belt from slipping off? I see no place for a belt adjustment. Which I know would eliminate the problem. Really aggravating to have to replace belt only after two uses.


On the roller/brush where the belt sits if that is scarred up or grooved out that will cause the belt to slip if you can fix roller try but i suggest new roller ... Hoover Company Wind Tunnel U53019 Upright Vacuum

Hoover Windtunnel - the belt keeps coming off & it is the correct


One compatible belt that I use and works (at least while its new) is Royal 104425001. Try that. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

I usemy hoover often, and last time I went to use it, it keeps blowing the circuit. It has never done this before, not in any of the plugins used, hoover or electrical problem?


It may be the motor is starting to short ... Hoover F7431-900 SteamVac Vacuum

Powerhead woes Drive belt for power head beater brush on Hoover S3755 keeps jumping off drive motor shaft when vacuuming low pile carpets like oriental rugs unless minimal suction is used. Any tricks to keeping the belt in place other than this?


I've had my Hoover S3755 for about 2 years and loved it, at least until the last couple of months when the "belt slipping off" problem started. I changed the belt and the vacuum would work for a little while then the belt would come off again. I pu ... Hoover S3755 WindTunnel Bagless Canister Vacuum

My hoover keeps giving me static shocks near the top on the plastic join. I have had the hoover a few months but it has only been doing this about a week.


Sounds like a wire has come loose and is grounding on the handle. ... Vacuums

The belt keeps slipping off. I bought a new one and it too slips off after about a half hour of vacuuming.


Check the motor shaft for loosness. when the bearings wear out and fail, the motor shaft will not be strait and the belt will ride off. also check for alignment and inspect the brushroll for proper installation, free rotation, and non melted endcaps. ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

My hoover Wind Tunnel vacuum cleaner's motor spindle keeps overheating. Because of the high temperature, it keeps burning through belts (the big, wide ones). I have taken it in to the vacuum repair shop about three times now, and the problem has never been fixed. Does anyone have any advice on how to fix this or should I just buy a new vacuum?


... Vacuums

Vax hoover my vax hoover keeps overheating and cutting out.


... Vacuums

My Hoover Windtunnel does not clean carpet. The machine keeps grabbing the carpet. It appears that even with the switch set for carpet, the machine keeps acting as though it were set for a hard floor. How can I fix it?


Move the height adjustment up a little ... Hoover U6476-900 WindTunnel Vacuum

Sweeper belt Hey , i own a fantom thunder sweeper and recently my belt keeps slipping off, i've disassembled it and put it back on a hundred times but it keeps doing it after a few minutes of cleaning , Am i missing a part to hold it on or somthing else wrong i've cleaned it and checked all the ports just cant figure it out and cant find any info online thanks for your time tina


Greetings from GoVacuum.com,Have you replaced the belt with a new one yet? You may want to try replacing the belt, as with flat belts like the Fantom Thunder, they do stretch out 4 -5 inches after time. We in fact recommended replacing ... Fantom Vacums XT450K Upright Vacuum

I have a dyson hoover. up to last week it worked fine. now it will not hoover up bits!!! i have to keep taking the long attahcment off and using that instead which is not ideal!! hubby has checked underneath..all brushes seem to be rotating fine and its not the belt. any suggestions?


Check the inspection air tubes on the Dyson - you don't say what model this is - and each model does have air inspection tubes but can be different to each model - which can usually clog up with dirt/debris thus making the machine difficult to pick u ... Hoover Vacuums

Overheating Hoover My Hoover cyclonic 1800w keeps overheating and turning itself off, not sure if it's the filter, I've cleaned it but it didn't look very dirty.


Most likely caused by a lack of airflow. Check to see if you have airflow at the end of the hose. If not, Remove all of the hoses and ensure that they are not clogged. If there is airflow through the hose; check the air inlet immediately aft of the b ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

Hoover aquamaster recently purchased hoover aquamaster, trying to shampoo carpet, can't get water to come down tubes, water keeps going into dirty water tank.help!!!!!!!!!!!!!!!


Sounds like you need to attach the air hose\015\012\015\012with reservoir in place you clip on the lid with tubes attached, one of them goes down to the floor cleaning nozzle, the other tube should be about 20cm long with an end piece, ... Vacuums

Hoover 1900w keeps cutting out - Hoover Vacuums


Opened it up little senser near the moter on a wire moved away from the motor dont cut out anymore ... Hoover Vacuums

My hoover keeps cutting out I have washed the filters and changed the bag but still keeps cutting out every 15secs


... Hoover Vacuums

Have an lg Hoover and the red light on the handle keeps flashing and the blue light on the Hoover is also flashing and then it cuts out. Has little suction with the head on it but better when you take it off. How do I fix the problem?


... Vacuums

Hoover elite rewind belt keeps coming off - Hoover Vacuums


... Hoover Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0372 seconds