Having problems with your Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum ?

Hoover vac 6432-900 reverse cable broke this model # is correct about 12 years old wind tunnel bagged self propelled


Answers :

The quick and easy here is to just splice the cable and tape it. If you just cut the insulation back to get to the wire and get a couple 'barrel connector' at the hardware store. These are crimp style connectors and you need a small crimper to put the wire in and crimp it down tight. Then tape it up and it will work fine.
Repair Help & Product Troubleshooting for Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover vac 6432-900 reverse cable broke this model # is correct about 12 years old wind tunnel bagged self propelled


The quick and easy here is to just splice the cable and tape it. If you just cut the insulation back to get to the wire and get a couple 'barrel connector' at the hardware store. These are crimp style connectors and you need a small crimper to put th ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a Hoover SteamVac Spot/Deep Cleaner, model F5515. I've had it a little over 1 year. It will not extract dirty water from the floor. I've made sure the recovery tank is attached correctly and also that the stair tool is connected. Is there something else I can try??


... Vacuums

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless


Get over it and buy a new one!!! ... Vacuums

On my hover U6616-900 the self propell work fine on the med setting on med height carpet, but when I go to low height carpet and height set on med the self propell does not pull the vacuum and it is hard to push. Also if I raise the height to the highest setting the self propell works correctly and appears to clen. Any ideas? S/N 090400184555, think this vacuum is maybe 5 years old and my wife uses it lots. Should I think of maybe a complete overhaul or a replacement at this time?


This is a typical problem you are describing. I would recommend you change the belts, this will resolve the "hard to push" and most likely resove your issues. based on the s/n given you maching was made on sept 2004. ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

Hoover Bagless Hello,      My Hoover bag less (Model U5280-900) is not picking up dirt like it should.  The brush roll is spinning fine, but the bristles on it are only about one quarter inch long.  I am wondering how long they should be.  The vacuum is quite a few years old.  Do you think it is time to replace the brush roll.  Could you email me at [email protected] about this topic.  The product bar below did not contain my model no.  The correct model no. is above in my message.  Thanks


If the belt is more than six months old then change it even if it is not broken. then replace your filters if that doesnt work than check the hoses for a clog drop a marble down them and make sure it comes out. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

I own a self-propelled Hoover Wind Tunnel vacuum cleaner (Model U6425-920). I do now have an owner's manual and was wondering how to clean the Hepa filter on this model (*this model uses a vacuum cleaner bag also).


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=794479\015\012Generic problem for all Vacuums\015\012I own a self-propelled Hoover\015\012Posted by goh ... Vacuums

My self-propelled Hoover wind tunnel vac. cleaner is hard to push


... Hoover Vacuums

I have an old Shop Vac model 3331.5. This is a 12 gallon 1.5 hight peak shop vac with a detachable blower. After many years I decided to use the blower feature, but have lost the lost the manual. Question; how do I attach the hoses to the blower? The motor has that cap on it the direct the flow of air in one direction and the wide hoses do not fit over it. I may be missing a part, but I would think the directional cap would have to come off anyway.


Remove the cap that directs the air and insert the hose in there. ... Vacuums

I own a hoover steam vac model f5915-900 and i currently have two problems. 1. the brushes are spinning at a much slower speed. 2. the steam vac is not picking up the water it leaves on the carpet. Please help Josie


The reason the brushes are not spinning is because the belt is slipping, the belt is the bad that connects to the brush to a shaft that makes it spin. Next problam is it is probobly clogged. so water is not going through all the way ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

My Oregon Scientific BAR888 has 5 windows, 1. temperature, 2. humidity, 3. mb/hPa or inHg (switch at the back), 4. bars showing pressure changes over 24 hours, and 5. time/date. Window 3 gives an option to set something between 0 and 2500. Oregon say they only have one set of instructions for the BAR888 but they do not match my instrument as there is nothing included for my window 3. Trouble is I don't know what the 0 to 2500 relates to and therefore don't know what to set it at.(My model does n


... Vacuums

The fan on my Dirt Devil model 103 hand held vac cracked. I bought what was designated as the correct replacement fan but the hole in the center of the fan is a lot smaller than the shaft that it has


... Vacuums

I have a Hoover self-propelled windtunnel, purchased 6-04. It gets light use. I have replaced the v belt 3 times, once under warranty, and it must be replaced again. It appears to be in very good condition, but is stretched too big. When I purchased 2 v belts a year ago, one was already too stretched,but when my Dad took it back, the salesman put it on another model and said it was fine (Dad never mentioned this to me). Is there a way to adjust the vacuum to hold the belt tighter? Do they re


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=675093\015\012Generic problem for all Vacuums\015\012I have a Hoover self-propelled\015\012Posted by kl ... Vacuums

After two years, my Euro-Pro Shark Steam Mop, Model S3101, no longer ejects steam. I have used tap water. I think the line is clogged with mineral deposits. The light is on when plugged in, and the unit heats up. I even put in vinegar for about an hour to break up the calcium deposits, but it did not correct the problem. How do I fix it, or, where can I take it locally to be fixed (Orange County, CA)?


Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

I have a Breville Vac Master model no. BHV9. I can't get it to recharge although the light is on. It is 6 years old. Could this be because it needs a new batterry?


... Vacuums

Hoover, model # UH30070 Wind tunnel vacuum Brush won't turn. I do not see how to remove this to replace the brush, and besides it's only about a year old! Why is it already broken? There's no visible evidence on the brush that would make it stop, i.e. string, clogged, etc. Can you help?


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a Shark Steam Mop, model S3101, that caught on fire. Looks as though a wire inside rubbed until it became exposed and then caught fire. I have had this unit for about 1 1/2 to 2 years; liked the concept of steaming my floors rather than using detergents. I am not happy though about spending $100 on this unit and then it only lasted this long.


... Vacuums

Belts I have a Hoover self-propelled windtunnel, purchased 6-04. It gets light use. I have replaced the v belt 3 times, once under warranty, and it must be replaced again. It appears to be in very good condition, but is stretched too big. When I purchased 2 v belts a year ago, one was already too stretched,but when my Dad took it back, the salesman put it on another model and said it was fine (Dad never mentioned this to me). Is there a way to adjust the vacuum to hold the belt tighter? Do t


It is the flat belt that gets stretched and should be replaced at least every 6 months. The V belt wears down so it won't it right in the brush roll V. Maybe the belt tensioner wheel has a problem, sometimes they get hook up and won't engage the V ... Vacuums

Self propelled vac: goes great on hard floor or hard slick carpet. Goes backwards fine but will not pull itself forward very well. Requires some effor to push it forward. I have adjusted the cable so the lever on the motor goes as far forward as possible. Suggestions? Model U6446-900


Dear Nasherrill,\015\012\015\012I've found a friend! I thought I was the only person in the world who owned the Hoover Model U6446-900! This model does not appear on the http ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Motor died I own a fein vac that is perhaps five years old. It appears that the motor is toast. Is it possible to order a replacement and install it myself? My model # is 9.11.20 Thanks for reading, Kevin


Yes you can its very easy you will have to get the model number the serial number and that will help you find one online try sites like vac motors or anything related, i have worked on industrial vacs mostly so my connections will not help you but yo ... Vacuums

Self propelled model. when plugged in vac won't start, dead no lights, no sounds


You may have a bad plug/cord. sometimes the transmission on the motor goes bad. any vac shop can fix it. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I am trying to find the powermate parts to replace the roller brush on this vac I have trouble finding websites that sell these. I need to know the item numbers so that I can order the correct items to fit this model.


Brought the powermate part to local Sears part store and they ordered the items we needed \015\012 thanks for trying to help \015\012\015\012GFreckles913/Glenna Rodell ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Folks, My wife and I own a three-year-old Hoover U6434-900 self-propelled "Wind Tunnel" upright vacuum cleaner. The problem is that, even on the highest setting (front-end as high as possible), it gets bogged-down in even shallow pile carpet to the point that the brush stops. I've cleaned the machine thoroughly, pulling hair, thread, dental floss and such from the brush (and everywhere else), including unscrewing the brush end caps and pulling out the cat hair mats which formed in there.


Check to see if the V belt sits too deep in the brushroll groove, if it sits too deep you will need to replace the brushroll. the top of the belt should be about flush with the brushroll. also you have to take the screws out of the self propelled uni ... Vacuums

Hoover wind tunnel cyclonic U5780900 1 year old. brush will not turn. too much slack in vbelt when in carpet position. Belt is good


Well, the V belt is normally fairly slack until the handle is dropped below 45 degrees, which is when the belt tensioner assembly drops into place. If turning the brushroll by hand when the vacuum is in this position fails to rotate the self propel p ... Hoover Vacuums

I just purchased a westclox tech model 70014 yesterday. I read the instructions and set the time. About an hour later, the time reverted back two hours. I read the instructions again and repeated setting the correct time. I assumed it was working. However, I woke up by myself today at 5:30am, but the clock read 1:14. Is there any way I can fix this or is it a manufacturing defect?


... Vacuums

I need to replace the brushbaron my DC17 Animal model Dyson. It's almost four years old. I can't find the correct part number on the Dyson Website and I can't seem to find a Dyson repair center in Albuquerque, NM. What are my alternatives? If I can't service this machine without returning it to Dyson, I won't ever buy another one.


Hi,\015\012\015\012The original Dyson part number for the brush bar (often called brush roll) is: 911961-01\015\012\015\012If you type the above part number into Google Products (click link below) you will get a list of suppli ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0893 seconds