Having problems with your Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum ?

My hoover tind tunnel model 5453-900 series the belt keeps slipping off the agitater brush-what can i do to fix it

Answers :

Your belt has probobly stretched even though it continues to function. try a new belt assuming the belt path is clear and any guides are properly positioned when the cover is properly replaced and the hump on the brush roll that contacts the belt is not mishapen.
Repair Help & Product Troubleshooting for Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My hoover tind tunnel model 5453-900 series the belt keeps slipping off the agitater brush-what can i do to fix it

Your belt has probobly stretched even though it continues to function. try a new belt assuming the belt path is clear and any guides are properly positioned when the cover is properly replaced and the hump on the brush roll that contacts the belt is ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover Wind Tunnel 7500 Brush not Turning. I have replaced the Brush and the belt. The problem does not seem to be either to me. I believe might be a missing part. The place were the belt hooks on is a metal pole which never seems to grip the belt well. In fact it seems loose most of the time and slips on the brush, causing the belt to eventually burn up. Could there be a missing plastic or rubber piece meant to hold the belt taught  on the metal pole?

Check the Idler Pulley part Number 43241004 (Item 13 in the IPB) ... Vacuums

My Eureka Boss 4870 belt keeps fraying, stretching, and breaking. When I replace the belt and turn the roller brush by hand, within just a few turns the belt drifts off center and to the left of the roller brush where it starts to rub. How do I fix this?

... Eureka Smartvac 4870 Bagged Upright Vacuum

My hoover Wind Tunnel vacuum cleaner's motor spindle keeps overheating. Because of the high temperature, it keeps burning through belts (the big, wide ones). I have taken it in to the vacuum repair shop about three times now, and the problem has never been fixed. Does anyone have any advice on how to fix this or should I just buy a new vacuum?

... Vacuums

The belt keeps on slipping off causing the brushes to stop

Over time the belt stretches and gets to big to stay put all of the time. Get a new Hoover belt and install it. That will solve your problem ... Hoover S3755 WindTunnel Bagless Canister Vacuum

The small belt attached to the roll brush keeps slipping off. It's a brand new belt and the vacuum is only 1 yr old.

The small belt rarely gives the problem you describe. The larger belt can jump off if the belt is worn or if th roller gets caught on something suddenly.The belt should be replaced every 9 - 12 months. If your carpet setting is too low this will caus ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Need help with Hoover S3765-040 WindTunnel Electronic Bagless Canister Vacuum. The belt that rotates the brush keeps slipping off. what to do?

The belt could be stretched and that could be causing the slip. Or you could have the wrong belt if you've replaced it recently ... Vacuums

Kenmore upright vacuum belt keeps breaking as soon as I put a new one on. I have made sure the brush roller is clean. How can I fix this or troubleshoot this?

... Kenmore 31723 Vacuum

I have replaced the correct blets and lined themupon the pulley but the v- belts keeps slipping off the pulley and than the brush will not spin

The pulley is not adjusted properly so the belt is slipping.\015\012There is a small wheel/pulley that keeps the v-belt tight and it is stuck.\015\012to adjust the pulley try this system. move the carpet height control lever and the brus ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

Have model 3576-6 Bissell Cleanview II and drive belt keeps slipping off peg that is sticking out from motor pulley causing vacuum to stop working properly and brush to stop moving properly

... Vacuums

Hello. My dyson dc04 keeps making a loud screeching noise when im vacuuming. It seems as though the plastic from the brush is catching on the plastic on its holder either side of the belt. Is there any way of fixing this problem?

Remove base cover by 3 'screws' 1/2 turn anti clockwise and clean well remove fibres replace cover and re try. ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My oreck belt keeps slipping off of the the brush. Please help!!!

... Oreck XL Ultra Bagged Upright Vacuum

Eureka 5843 belt keeps slipping off of drive spindle.

Tough one. Typically the only 2 things that the belt contacts is the motor drive spindle and the brush roller. Anything else would only be there to protect the belt from debris. Can you turn the brush by hand and see why the belt is coming off? I ... Eureka Whirlwind LiteSpeed 5843 Upright Vacuum

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a

... Bissell ProHeat Deep Cleaner Upright Vacuum

Belt slipping Belt slips off and rubs causing burning smell from the belt over heating. Of course this puts an indent into the belt and has to be replaced. How do I keep the belt from slipping off? I see no place for a belt adjustment. Which I know would eliminate the problem. Really aggravating to have to replace belt only after two uses.

On the roller/brush where the belt sits if that is scarred up or grooved out that will cause the belt to slip if you can fix roller try but i suggest new roller ... Hoover Company Wind Tunnel U53019 Upright Vacuum

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o

Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Hoover windtunnel u6476-910. Brush does not roll. Flat belt and other belt are good. The other thicker belt (called V belt?) does not have tension with the brush roll. How do I make sure it is engaged? Is there a fix? Settings are in "Carpet", "Roll-on", etc. Cleand all hair and bags/filters already.

These machines had a defective switch and a bulletin was sent out to all service depots. If you contact any Hoover Warranty Depot, they will replace the switch, wiring harness and tool receiver under a no-charge warranty. It doesn't matter how old it ... Vacuums

Hoover windtunnel t series belt is loose- roller brush doesnt turn. Its brand new belt is slipping. we bough new belts and putthem on same problem. Can not find solutio in manual. Is the belt supposed to go around the "metal pulley". I know it goes around the little metal motor thing, then thru the guide and around the brush. What is the metal pulley??? Is is the larger round silver thing between the guide and roller?

I also have a loose belt and have bought additional belts but have the same problem. I put the it around the metal rotor and around the brush roller a shown by he Hoover video, and it is loose. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Kenmore Canister Vac, Progressive, 25512 255513 model. Brush won't turn. One end of the brush roller, end closest to belt, is off center which is keeping it from turning freely. The end cap is like a square. Other ends turns fine. Do these end caps come off? If so how? Can't get it to budge. This is exactly what is keep brush roller from turning.

Take a flat head screw driver and pry the end cap off. It will come off. You might have some string or hair around it causing it to not turn. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Hoover Wind Tunnel - Belt Keeps Coming Off

This is the same problem I had. We took it to a vacuum repair store and they fixed it for $80.00!! It lasted about 6 months and it just happened again. I'm not spending the money - I'm looking for another vacuum cleaner. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Windtunnel belt I have a new Hoover Windtunnel canister. The belt keeps coming off. It happened a couple weeks ago (several times after putting the belt back on) so I assumed I might need a new belt as it might have dried out at the store. I ordered new belts and today I used it for about an hour and the belt came off again, twice. There doesn't seem to be anything to hold the belt on the stem as it seems to slip off. I have tried it centered, to the left and to the right....can you help. I am v

I've successfully used a compatible belt - Royal 104425001 .It's still new, but for the time being at least - it works. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Hi,My agitator brush won't run on my hoover S3590, I changed the belt, that didn't work. I don't see a possible cause in my book except replacing the belt. I think there could be a short, the brush will come on sometimes when pulling back and slightly lifting. Any ideas would be great and can I fix it myself? Thank you for any help, Bobbie

Hi Bobbie\015\012Take apart the electro floor head if you can and inspect inside - it may well be that there's clogged dust preventing the brush from turning and also check both sides of the actual beater bar as thread and tangled hair can often lead ... Hoover S3590 Bagged Canister Vacuum

I was replacing the belt on my Eureka Smartvac 4870 and one of the felt gaskets (or part of it) popped out. I thought I put it in correctly, but the first I used it after replacing the belt, the gasket got mangled by the brush. I'm wondering how important it is to get fixed; is it a part I can pick up anywhere and fix myself? Thanks for the help.

I'm no expert but if you mean the felt on the roller, you have to replace the roller (expensive,esp. for such a minor part). So. I found some felt with adhesive in the craft section at Wal-Mart, trimmed it to fit and done deal. Felt reduces friction. ... Eureka Smartvac 4870 Bagged Upright Vacuum

Sweeper belt Hey , i own a fantom thunder sweeper and recently my belt keeps slipping off, i've disassembled it and put it back on a hundred times but it keeps doing it after a few minutes of cleaning , Am i missing a part to hold it on or somthing else wrong i've cleaned it and checked all the ports just cant figure it out and cant find any info online thanks for your time tina

Greetings from GoVacuum.com,Have you replaced the belt with a new one yet? You may want to try replacing the belt, as with flat belts like the Fantom Thunder, they do stretch out 4 -5 inches after time. We in fact recommended replacing ... Fantom Vacums XT450K Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0847 seconds