Having problems with your Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum ?

The brushes will not rotate on my hoover vacuum. the belts are in good shape, the motor is turning the vacuum motor, but the belt on the brushes seems loose. I ordered a replacement belt but still nothing. Their is a small "idler" but their dosent seem to be enough tension on the belt. Any ideas?

Answers :

Did you order the correct size of belt? These are the belts you should have:

Hoover Windtunnel Belts
Repair Help & Product Troubleshooting for Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The brushes will not rotate on my hoover vacuum. the belts are in good shape, the motor is turning the vacuum motor, but the belt on the brushes seems loose. I ordered a replacement belt but still nothing. Their is a small "idler" but their dosent seem to be enough tension on the belt. Any ideas?

Did you order the correct size of belt? These are the belts you should have:Hoover Windtunnel Belts ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the

Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

How to disassemble the brush to empty anything that might be stuck inside of the brush? The motor seems to be overheating, all belts have been checked, all airways are clear and the filter is clean. The vacuum is vibrating and releasing a burning smell, but still sucking up dirt. There is nothing stuck on the outside of the brush, but is there a way to check inside of it to see if that is where a clog is occuring?

If there's a burning smell and the belts are fine, the problem is going to be hot wires causing the insulation to melt, or the motor going bad. Discontinue use and have it checked at a repair shop. ... Bissell 6594 PowerForce Bagless Upright Vacuum

My kenmore vacuum model 116.36933502. It has no suction. I have cleaned out every spot,taken off the back and still nothing. The motor runs but doesnt seem to be at full power. The agitator brush works. When it broke i seemed to smell something and since it has no belt. Does this possibly have to motors?

... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.

The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi

Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum

When I vacuum w/ the brush control in the on position it make a really loud noise, almost like a grinding sound. I have looked at it and nothing seems to be wrong, but I notice that the pin that engages the belt seems to vibrate a bit, possibly creating the noise. It started when I accidentally got part of a plastic grocery bag caught in the brush. Could it have stretched a belt? Nothing is caught any other place and it only makes the noise when the brush in in the on position.

Yes, the belt could have been stretched and is now vibrating and hitting other parts and creating a noise if much of the bag got caught under the belt. If you have another belt for this vacuum, please put it on and see if the noise stops. If it does ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

We own a dirt devil model 088600, and are experiencing a problem with the belt wearing away a section between where the belt connects to the brushes and the motor. There is a lot of plastic/rubber residue coming out from the vacuum. We have tried new belts only to find the same problem occurs. I noticed that the source of the dust is coming from the section between the brushes and motor, where there appears to be a section that is misshapen and melted. I looked up the schematic online and can't

If you are certain that the belt is seated correctly and the beater bar is nested in its holder and the cover of the assembly has been properly installed and you still see a contact area between the belt and cover, you should either: return the vac ... Dirt Devil Vacuums

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc

... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn

Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum

I have a Kirby Dual Sanitronic '50' Vacuum Cleaner I bought in 1966. The motor does not start when I attach the belt lifter of the rug nozzle. When I remove the rug nozzle and detach the belt from the motor fan shaft the motor starts when I depress the nozzle switch and the power switch . Seems like the brushes in the motor are worn out. I do not have a manual for this unit. Can you assist me as to what newer unit is this compatible to and the problem I'm having at present??

... Kirby Vacuums

I have a Bissell Lift-off Revolution Turbo vacuum and the brush doesn't spin on its own anymore. Does this mean the motor is busted because there's no noise when you press the brush button. We've just replaced the belt, hepa filter and a new brush. But its still the same. What's wrong with my vacuum?

Its probably the motor. remove the covers with a #2 phillips head screwdriver and cut the wires to the motor ( unplugged ). purchase some crimps at radio shack to resplice the wires together in the same fashion. ... Bissell Vacuums

On an old upright prolux plus, I just replaced the belt and cleaned out the brush motor, ran the vacuum for a bit, then the vacuum motor died...it's always run great. any suggestions of what to check?

... Electrolux Vacuums

A small thin antenna cord on my radio got sucked up, and I immediately turned my vacuum off and easily puled out the small cord, Afterward the brush on the vacuu would notrotate.. The belt is not broken on the vacuum is not broken. My husband cannot figure out what the problem is

Hi Susan. There may still be a piece of the cord in the brush roller bearing. Check the ends of the brush and have a look. If its clear the belt is probably strethed. An easy way to test this is to turn on machine a put you hand against brush, if it ... Riccar 8955 Upright Vacuum

My Eureka Altima vacuum the brush is not spinning. I took it apart and the belt is Not broke, but when I turn the vacuum on I can smell the motor overheating. I turned the machine off and unplugged it and then took it apart so I could see the underneath and plugged it back in and the belt still won't turn..can you help?

Hi, since you have detected the the smell of the overheating motor, then the motor is faulty which is why the belt is not turning. You should change th motor ASAP........... ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I have a problem with my model 6585-3 bissell upright powerforce bagless turbo with turbo brush vacuum The brush has quit spinning upon removal i noticed that one side of the brush was free to spin the other side that has the rectangular piece to help hold into place seems to be locked up and will not spin is it corroded or have i lost a piece that joins with it that allows it to spin freely belts are good and motor is turning brush will not budge

... Vacuums

How to repair BEAM Central Vacuum Power Brush. Motor works perfectly, belt brand new but unable to spin brush.

... Vacuums

Trying to replace belt on hoover convertible bagless upright u8188900. belt replace # 38528-049. i have opened vacuum and put belt back on, but it will not get tight enough around the motor gear and the brush spool to be able to activate. am i missing something? mike

... Hoover Vacuums

The belt on my used Eureka Boss 5857 upright slips off the end of the motor shaft every time the vacuum is used. When I turn the brush roll slowly by hand, the belt walks toward the end of the shaft. It looks like there was a plastic projection from the base that snapped off, and maybe that plastic piece used to block the belt from falling off. Do I need to try to reconstruct that plastic piece, or is something else wrong?

... Eureka 5856BVZ Boss Bagless Upright Cyclonic Vacuum

My vacuum's rug brush will not spin. the belts are fine and in place, but when i engage the carpet brush nothing happens. i looked under the bottom and there are no obstructions preventing the brush from opporating/

Have your clutch checked out by a local vacuum repair shop. That's a common problem with dyson brush rollers ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Replacing a belt on the Riccar 8850...I see how the brush assembly will work with the new belt. But I don't see how a new belt will turn on the small rod extending from the motor. Is there a pully missing?

There is not a pulley missing, when the belt is tight the shaft will turn the belt but when the belt loses elasticity it will slip on the shaft when being used on the carpet. Replace the n\012belt at least once or twice per year. ... Riccar 8850 Vacuum

I have an electrolux genesis upright vacuum that I bought used about 8 years ago. It has been A great vacuum the best I ever had. I thought the belt had come off so I took it in for repair. They called today and said that the brush rotor motor was bad and it would be around 148.00 dollars to repair. My question is could I buy the part and have my husband replace it or would it be too complicated. Can you still buy an electrolux vacuum comparable to this one and how much are they. I love this vac

... Vacuums

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag

... Euro-Pro EP621 Bagless Upright Vacuum

Powerhead woes Drive belt for power head beater brush on Hoover S3755 keeps jumping off drive motor shaft when vacuuming low pile carpets like oriental rugs unless minimal suction is used. Any tricks to keeping the belt in place other than this?

I've had my Hoover S3755 for about 2 years and loved it, at least until the last couple of months when the "belt slipping off" problem started. I changed the belt and the vacuum would work for a little while then the belt would come off again. I pu ... Hoover S3755 WindTunnel Bagless Canister Vacuum

I have looked online for this vacuum but could not find it. The closest one is the Eureka 8803 but the p/n on mine says 79307. I have totally disassemble this vacuum. There are no clogs anywhere. Motor spins by turning shaft. Belt is new and turns brush. It still has absolutely no suction.

... Eureka Boss Capture 8803AVZ Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1551 seconds