Having problems with your Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum ?

The hose works great, but the head of the vaccuum does not pick up anything !!! I checked every opening that may have been clogged, but nothing came up. When I hold my hand under the brush/roller, it seems to be putting out more air than intaking air. Particles "dance" on the carpet, but don't get "sucked up" into the vaccuum ? I have had the vaccuum only 1 year, so the brushes should not be a problem. I changed the bag, and checked the belt. The belt and brushes seem to be OK. ?


Answers :

Hi there,

Uprights are notorious for debris forming clogs when changing direction. The 90 degree turn where the base suction goes up. Have a closer look . You may need to pull the base plate off to access the blockage.

Best regards
Mike
Repair Help & Product Troubleshooting for Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The hose works great, but the head of the vaccuum does not pick up anything !!! I checked every opening that may have been clogged, but nothing came up. When I hold my hand under the brush/roller, it seems to be putting out more air than intaking air. Particles "dance" on the carpet, but don't get "sucked up" into the vaccuum ? I have had the vaccuum only 1 year, so the brushes should not be a problem. I changed the bag, and checked the belt. The belt and brushes seem to be OK. ?


Hi there,Uprights are notorious for debris forming clogs when changing direction. The 90 degree turn where the base suction goes up. Have a closer look . You may need to pull the base plate off to access the blockage.Best reg ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Roomba. Diagnostic The brushes will not rotate. I have cleaned them, used an air compressor, and checked the front wheel. What can I do to get the brushes rotating?


Go to homesupport.irobot.com and get contact for help.and get the parts too.God bless you ... iRobot Roomba 560 Robotic Vacuum

Suction Problem I took my unit to my work and used it, when I returned home it wouldn't suck up anything. I took the recovery take out and it has inward suction. Shouldn't that be outward, so it goes into the tank? It also blows out of the bottom by the brushes. I check the filter in the bottom and that is fine. Is it possible that it is somehow reversed the direction of the air flow (rotor running backwards)? I am perplexed. What am I missing?


There is a stand pipe seal where the bucket sits on, and if it isn't there or out of place could cause a suction problem like you said yours is doing. In the picture it is #10. The motor seal may have gone bad and is leaking # 15.\015\012 ... Hoover F7220900 SteamVac V2 Upright Vacuum

Hi my dyson is not sucking up very well when i put it on its side and switch it on the brushes are not going round when i put the white dail to on at the bottom the brushes go round but it makes a terrible noise i have cleaned the brushes checked the soleplate is on correct and taken the clear hose off and checked for splits the suction is there when i have been checking these things hope you can help thx


Hi there,Sorry to hear you're experiencing a problem with your cleaner. Please get in touch with us, free, on 08002980298 (UK), or 1866MYDYSON (US). We can run through some checks over the phone and provide you with the assistance you nee ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a Hoover spin vac # 7410-900 the brushes don't spin but i can hear the pump running , checked the brush block stem thats fine the unit feeds water and soap. but i have no vacuu.me or brush movement getting ready to rip the turbine out to check it . the weird thing is it worked fine and then just stopped


... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

How to disassemble the brush to empty anything that might be stuck inside of the brush? The motor seems to be overheating, all belts have been checked, all airways are clear and the filter is clean. The vacuum is vibrating and releasing a burning smell, but still sucking up dirt. There is nothing stuck on the outside of the brush, but is there a way to check inside of it to see if that is where a clog is occuring?


If there's a burning smell and the belts are fine, the problem is going to be hot wires causing the insulation to melt, or the motor going bad. Discontinue use and have it checked at a repair shop. ... Bissell 6594 PowerForce Bagless Upright Vacuum

My brushes do not turn on my power glide pet vacuum cleaner after I accidentally sucked up the hem of a curtain. I switched off the machine then removed the hem. Now when the vaccuum cleaner is turned


... Electrolux Vacuums

I have a new STEAM VAC Dual V All Terrain Carpet and Hardwood Cleaner. I have used it once and it worked well. Now, the second time, I have no water return. I checked the tank location, the brushes are moving slowly (but the plastic surrounding around the brushes moves as well ??) Water is coming out. There is hot air blowing out, but there is no air suction. What is wrong? Ursula Litzcke


Hello litzcke.\015\012There are lots of people facing this problem as well as other problems with this machine. As there are lots of faulty with this product; would not **** up water/air/shampoo, will not brush and lots more. If it is under war ... Vacuums

My vacuum blows air instead of sucking air. I have a dirt devil swivel guide. I got something stuck in the brush spinner, got it out...but now the vacuum doesnt suck stuff up anymore.


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=571660\015\012Generic problem for all Vacuums\015\012My vacuum blows air instead\015\012Posted by katweaver3 on ... Vacuums

Suction stopped. Roller and belt working-in fine order. Checked hoses have not found any blockage. Blowing out air or sucking so little can't feel it with hand on hose end. Help!


Either a blockage or the main air filter is blocked , some it can be washed and others it must be replaced I would check the owner manual and look at the filter, foam ones can and usually have instructions where they install to wash them. ... Hoover Tempo Widepath Upright Vacuum - Blue

Scrubbing brushes I have cleaned the filter, checked the dial to make sure it is turned to high and cleaned all of the brushes. Still I can't get the brushes to rotate. What now?


Your turbine might need to be replaced ... Hoover F5881-900 Vacuum

Weird noise i have a eureka the boss and i am getting a weird noise figured bag was full needed to change it so i did. Noise persisted so i checked make sure nothing was caught in the brushes. I even checked the belt it was fine replaced with a new one.Still the noise is there help me I am out of what else to check.


Squealing ... Vacuums

Clogged hose A makeup brush (about 3.5 inches long) was sucked up through the vacuum hose. It won't come back through the same way it came in because the bristles in the brush are expanded. We can see the brush on the side of the hose that connects to the canister but can't get it around the bend of the 360 part of the hose... is there any way to take the hose apart more?


... Kenmore 25512/ 25513 Progressive Canister Vacuum

No power to sensor SR 12. I also have cleaned rollers and filters and bags. I have reset the handle. When I hit the power the check brush and full bag lights flash once. That is the only power that is getting through.The unit was in storage for a bit and got wet but its been drying off for a couple months. Is there something I can check or replace. Its a great Vac.


... Windsor SR12 Sensor Bagged Upright Vacuum

My Kenmore progressive upright vacuum, model 11635923500 has a problem with the brush rotating. Sometimes the brush will not rotate until the unit in lowered way down, like the activate switch has rotated. Can I get inside the unit to check the switch, if so were do I look


... Kenmore Vacuums

Hi I’ve got a Panasonic vacuum cleaner MC E468 1600W a few years old now but works well up to recent problem. Not picking up I checked the obvious things and found excessive air being sucked in around the hose housing at the back of the vacuum (as it enters the waste bag) On inspection it appears to me as if there should be some sort of gasket that may have perished and been sucked in, however I can’t identify any such part. Any thoughts on what the problem/solution may be will be appreciate


The hose on the back might be loose - check to see that the hose is not obstructing anything where it screws in at the back - or indeed the screws may be loose themselves; some of the MCE 468 models had an additional ring washer that sits between the ... Panasonic Vacuums

My DC17 is only a few months old, but I've already had to clean the filter. Since I reassembled everything, I'm finding chunks of carpet fiber and dog fur on top of the filter inside the filter container. Iam getting slightly less suction from the floor assembly as well. I've checked the hoses, brush, and brushed out the inside of the plastic container, but hasn't helped. Ideas??


Everyone needs to own an air compressor,\015\012if you own a bagless vacuum\015\012\015\012You blow it out every other time you use it.\015\012\015\012Without compressed air, all vacuums will just\015\012basically ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My Kirby Heritage II vacuum is not picking up dirt up out of the carpet like usual, and I have to keep setting it lower to pick anything up. I finally get it to such a low setting that it starts sucking the carpet up and makes a whirring noise, and starts smelling. Every time this happens, we find the belt has been burned. We are wondering if the brush roll inside with the brushes that pick up dirt are worn out and too short?


... Kirby Heritage II Vacuum

Dyson DC17 Just got it back from repair, at first use, snagged fringe for a moment, and now get no brsh action again.  Checked the brush belt and it is fine.  Is there a second belt for the clutch, and how do i get to it to check it as well?


Yes you have to take the cover of underneath three srews you will need T15 SCREW DRIVER ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

No "sucking" action i'm not getting any air to **** up anything, i cleaned it up put new belt on, doesn't look like there are any obstructions can't get it to **** up anything


Did you check to see if the beater brush was rotating properly?\015\012When it doesn't it usually causes the belt to burn and break, though I do not believe you had a belt issue.\015\012\015\012If you remove the beater brush like you did to rep ... Hoover Tempo Widepath Upright Vacuum - Blue

My Kirby G3 paint attachment isn't spraying the paint. I have everything hooked up according to the manual, and it sprays a continuous stream of air, but isn't sucking up the paint to spray. Sometimes I can get short spurt when I point the unit directly down, but i can't get a continuous spray.


Mcdevito75 here, Sounds like it"s cogged with paint, the paint is not being sucked up into the Spray gun itself, the air flows thru thr spray gun thru the trigger assembly. Follow the makers cleaning of the spray section of the spray gun. Try running ... Kirby Generation 3 Bagged Upright Vacuum

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag


... Euro-Pro EP621 Bagless Upright Vacuum

Dyson Animal I sucked up a part of sock didn't get sucked up turned it off and pulled out sock but beater brush won't come back on.


Happened to me too. there is a reset somewhere, i got mine working again. try the Dyson website, sorry ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I put in a ne Kirby Bag and it still is not sucking up the dirt. The brush is turning but the bag does not seem to be getting any sucking snce it is not expanding


See if this helps:\015\012http://www.goodvac.com/kb_results.asp?ID=13\015\012\015\012Good Luck,\015\012Rocky ... Kirby Ultimate G Bagged Upright Vacuum

Eureka 4467AV overheats and shuts down after about 3 or 4 minutes of operation. I pulled all the filters to assure no blocked air flow. I assume the motor is not getting enough cooling air but i can't figure out why. checked bag for blockages as well as hoses. could the thermal protection have gone bad?


... Eureka 4467AV Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0667 seconds