Having problems with your Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum ?

Vacuum belts how do i put a new belt on my vacuum?

Answers :

I can't do it
Take off the bottom plate, there are 2 belts, the V belt (38528034)goes on first, it goes around the pulley then around the brush roll. The Flat belt(38528035), put it around the motor shaft first, then stretch it to go over the bigger pulley.
Repair Help & Product Troubleshooting for Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have two old identical 5842's that I use in the garage and around the house. The belt broke on one so I bought a bag of 2 genuine Eurika "U" belts, which is the correct belt for this vacuum. They were obviously smaller than the original belt because they were not stretched out. When I put the new belt on it lasted about 20 minutes and then came off. I put it back on and ran the vacuum with the cover off to see what was wrong. Everything looked fine except the belt rides to the outside edge of

Not 100% sure this is the remedy for that particular problem, but I would take the time to clean both of the brushes that the belts operate, one on each machine.\015\012Remove the brushes and clean as best you can. At the end of each brush there sho ... Eureka Whirlwind Litespeed 5840 Bagless Upright Cyclonic Vacuum

I have a kirby sentria. vacuumed up my son's headphones and immediately shut if off. took brush off, unwound headphones, put it back together. when i turned it back on, the belt snapped. so i went to vacuum place, got new belt, but when i put it on, with the green arrows lined up, it doesn't have much suction. with the red arrows lined up, it just smells like its burning and i don't want to break another belt! HELP!!

Take the front off the vacuum and check inside both the front portion and the canister for additonal clogs. Sometimes something will get caught in the impellor, causing the motor to overheat. Since there's little suction and the smell, I'd guess th ... Kirby Generation 3 Bagged Upright Vacuum

I have a Eureka 4800 series the Boss upright with a bag and Hepa filter. I love it! I was just vacuuming with the hose part and all was well and then suddenly the lower brush came on and a "burning" smell followed. Thought it was the belt so my husband was going to put on the new belt which I had on hand! When he turned it over, the "bar" that holds the belt looks as though it "shot through" the plastic side of the housing on the vacuum. There is melted plastic on the outside of the vacuum and o

I had the same problem. Take out the old belt if possible. Remove the 4 screws inside the filter and the 3 on the front of that housing. pull out the foam around the motor. carefully pull out the suction tube that is press fit against the motor. ... Eureka 4874 Bagged Upright Vacuum

The belt on my vacuum cleaner model 6596 bissel powerforce bagless turbo keeps breaking. As soon as I put on a new belt and start it up the belt snaps. It is the durabelt meant for this vacuum model. Also, my son has been having the same problem with his. He has the same model and same belt. This problem is occurring even after a thourough cleaning.

I would guess you aren't centering the belt correctly, thus it's edge is caught between the brush and another solid object, causing the breakage.\015\012When you get the belt on the the brush and the brush back in place, turn the brush a few ti ... Bissell 6596 Bagless Upright Vacuum

Oreck vaccum when i put a new belt on, the belt rubs the side of the wall of the vacuum gets real hot and busts. is there any type of washer fitting that goes on the vacuum to hold the belt in place? i dont know i need help thank you. you can reach me at [email protected]

The belt must not be running true to the pulley. You may need a brush roll, but also check the motor to make sure it isn't moving inward after the belt is put on. ... Oreck XL Ultra Bagged Upright Vacuum

My oreck upright smells like rubber burning when i vacuum. i just put a new belt on but it smelled like that before i even put the belt on

... Oreck XL Ultra Bagged Upright Vacuum

Vacuum belts how do i put a new belt on my vacuum?

I can't do it ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Belts I have recently bought new belts and when I installed the green light only comes on sometimes and I can smell rubber burning. The last belt broke very quickly so I am assuming that when I put the vacuum back together I am doing something incorrectly. Can you help instruct me?

Recently received a kirby from mother in law and don't how to change the belts ... Kirby Ultimate G Bagged Upright Vacuum

I have a self propelled Royal Dirt Devil vacuum model number 087900 and it goes backward fine but forward has to be pushed so hard it's impossible. Is this a switch? Do you know about how much the part would cost and can it be done by a beginner. We fix a lot of things ourselves but we aren't mechanics by no means. We put a brand new belt on it. I don't think it can be put on backwards and brush turns fine. Where is the switch? Use layman's terms.

You might try a new belt and/or brush roll. The brush roll is what helps pull a vacuum forward, the power drive helps, but if the brush isn't turning like it should, then it will hinder forward motion. The belt may look ok, but they stretch to the ... Vacuums

The belt broke and after putting on new belt I dicscovered the cylinder with the brushes attached wasn't turning. After I finally got the cylinder to turn it makes a very very loud noise and also now it doesn't pick up the dirt. The vacuum is less than a year old.

Check the cylinder with brushes does not have hair or carpet fibers causing it to bind. With the belt removed the brush should turn freely and fairly easy. The original belt probably broke because of this. You may have to fully dis-assemble the head ... Dirt Devil Vacuums

I have a eureka surface max 300, i saw smoke come out of my vacuum i seen that the belt was broke every time i change belt i run it on it snaps every time ive put 3 new ones and each one break right when i start it it looks like the metal piece is burning it is there a piece missing?? what am i doing wrong?? ugh i just purchased it couple of months agoo not even older then 6 months .. what do i do?

... Eureka Capture Upright Vacuum Vacuum

Have a Morphy Richards 1500 watt cyclone Ultra Light vacuum cleaner Model No. 73320. Belt has broken and I have lot the manual. Need instructions as to how to put in a new belt

... Morphy Richards Vacuums

How to put a new belt on a kirby vacuum - Vacuums

Here is a link to changing the belt on a Kirby vacuum cleaner http://www.totalvac.com/videos/kirby-vacuum-cleaners-videos.htm ... Vacuums

How to put a Kirby Vacuum belt back on New belt seems too short

To put on a kirby belt all you need to do is put on the belt on the brushroll, put the brushroll into the housing making sure the marks on the end of the brushroll are the same. Take the spin dial in the front and "hook" the belt till the dial reads ... Kirby G5 Bagged Upright Vacuum

Put on a new beater brush belt that I bought from Sears as detailed on the plate on the vacuum. It immediately snapped. Is there a diagram for the routing for the belt (there is a drive spindle and a tensioner)? Thanks.

I would first check to see if the beater brush is turning freely. You should be able to turn it by hand. If you can not, remove it from the vacuum and clean any debris on the brush and especially on the ends that hold it in place.\015\012Some WD40 ... Kenmore Whispertone 29512 Vacuum

Have Hoover Wind Tunnel Sel Propelled vacuum. Had to put on new drive belt. Turn on unit and drive belt slides off the drive spindle.

Look for excessive wear on the unit around the pulleys and their brackets that hold them in place. It sounds like something is just worn out and the belt is either slipping because it is not tight enough or because something is not aligned straight. ... Vacuums

The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t

The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum

Hello I have a hoover vacuum cleaner, it's an older one model number 44535830.....I bought a new belt but have no idea how to put it on? can you help me

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=542810\015\012Generic problem for all Vacuums\015\012Hello I have a Hoover\015\012Posted by rrunner ... Vacuums

Kenmore upright vacuum belt keeps breaking as soon as I put a new one on. I have made sure the brush roller is clean. How can I fix this or troubleshoot this?

... Kenmore 31723 Vacuum

I am trying to install new belt. I got the bottom of the vacuum off, but now I need a diagram on how to put it back together.

... Eureka 431A Optima Bagless Upright Vacuum

I put a new belt on my vacuum and right away it broke

There may be a problem with the brush roller itself. When the belt is removed and you have the brush in your hand, make sure that you can turn it. \012\012If the brush turns fine, what I suggest is put another belt on, and before you clos ... Bissell 3576 CleanView II Bagless Upright Vacuum

How do i put a new belt in kirby vacuum ultimate G

You'll want to rotate the front plastic piece 270 degrees until the red triangle on the plastic piece lines up with the red triangle on the top of the nozzle. Then, rotate the nozzle release (located under the headlight assembly) until the nozzle can ... Kirby Vacuums

How do i put new belt on - Bissell 7901-R Clearview Proheat Plus Upright Vacuum

How do I change on my Bissell Proheat Clearview Model # 1699-W ... Bissell 7901-R Clearview Proheat Plus Upright Vacuum

Putting a new belt on on my kirby sentria - Kirby G6 Bagged Upright Vacuum

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=780370\015\012Generic problem for all Vacuums\015\012Putting a new belt on\015\012Posted by cowangelgir ... Kirby G6 Bagged Upright Vacuum

How so you put the new belt back on - Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0779 seconds