Having problems with your Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum ?

Hoover Wind Tunnel U6458-900 Self Propel doesn't work - via other expert advice here for other models of Hoover - I'm thinking it is the actuator that needs to be replaced as I can see the cable does not connect to anything on the bottom. My problem is - I can't get the cover off. Been trying for a couple of hours. I removed every screw I can seem to find but something is hold it down. I also am wondering if/when I do eventually get the cover off, would I need to replace the cable when I replac


Answers :

On some models there are hook/springs that hold the cover of the base snug.
Repair Help & Product Troubleshooting for Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover Wind Tunnel U6458-900 Self Propel doesn't work - via other expert advice here for other models of Hoover - I'm thinking it is the actuator that needs to be replaced as I can see the cable does not connect to anything on the bottom. My problem is - I can't get the cover off. Been trying for a couple of hours. I removed every screw I can seem to find but something is hold it down. I also am wondering if/when I do eventually get the cover off, would I need to replace the cable when I replac


On some models there are hook/springs that hold the cover of the base snug. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I am trying to replace the cable and actuator on a Hoover windtunnel self propelled vacuum. but I cant get the top or hood off the get to them, I have removed all the screws I can see, roller, belts..what am I missing?? thanks so much for any help


Hi there SmartAlec from NelsonVacuums.com.au here. You will need to remove the knobs for carpet/hard floor selection and the carpet height to remove the cover they act as k ... Vacuums

Hoover Alpina 2 1300 cleaner. I need to split the upper and lower casings to check that the switch is working. I have removed the screwa in the area around the bag, but now need to remove the switch and cable rewind covers, as I assume there are more securing screws under them. Can you advise how to do it please?


Move covers (forcibly !) away from the centreline of cleaner then move to rear until released. The covers are held by slide catches on inner edges. ... Vacuums

Kenmore Model 116 Cannister Vacuum.Trying to get into motor area. Think belt is worn out. I have removed the front two screws under the hinged cover, but can not remove cover over motor.. Still attached at rear. No evidence of any more screws to remove.


Under the cordwinder actuator button, are your other two screws. To remove this cover, take a flat tipped screwdriver and , very carefully, find the "tabs" (there are two) both on the front section under the button. Then, Carefully, press them in a ... Vacuums

Agitator belt failed in my Hoover F5853-900 Steam Vacuum Cleaner. But can not remove bottom Cover .. have removed top cover and two screws from the bottom Cover. The smaller Cover is glued to the large Bottom Cover. Need help.


Hello,Unscrew the plate. check if there is any screws at the bottom, if none, exact little pressure to pull out the bottom cover. At this \015\012point you should be able to see the broken drive belt along with the two\015\012 drive bars ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I can't find the 4 screws to get to the belt on a dirt devil 22.0 Fx. The bottom of the vaccuum says " remove four screws from bottom of nozzle then lift top nozzle cover off", where are these screws, I can only find two, and which is the top nozzle cover?


... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

My vacuum cleaner is making a loud squealing sound when I turn it on and the brush is turning. It gets louder while vacuuming the carpet. I tried to remove the bottom cover to see inside but, took out a bunch of screws and couldn't get the cover off.


... Kenmore Progressive Direct Drive 30912 Vacuum

I have a Necchi LYdia 3 machine type 544 The motor was overheating and I removed the bottom cover and examined the motor .It looked fine and ran well. It worked OK for a time and then got hot.I was able to partially remove the motor for inspection.I found that the cooling impeller was not secured to the shaft,I tightened the set screws and reinstalled the motor. In process of getting the drive belt back on I turned the wheel that extends out of the case to index the screw that attaches the bobb


Good day!Please try to re align the motor position.You have to do is repeat the procedure that you take to remove the motor and double check the alignment because all motor in misalignment is very hard to turn.And ... Vacuums

How do you get to the 2 screws under the cord retraction pedal? I can not find any way to remove the pedal. I am trying toi remove the canopy cover in order to get to the motor>


What model is this for? ... Kenmore Vacuums

I want to open a Hoover S3825 Elite Cyclonic Vacuum to see if I can repair or replace the cord reel assembly. Currently the reel slowly draws the cord back into the canister once it is pulled out. I found the mounting screws under the rear wheels once I removed the hub but I do not know how to remove the rear wheels, everything is plastic. The front screws are under the front caster wheels and I think I need to take a screwdriver and pry off the little cylinder wheel to get to them by rotating


... Vacuums

I am getting very little suction from the motor. The hose is clear, the bag new. When I open the bag cover, plug the hose in and turn the vacuum on, there is next to no suction from the motor. What do you think is wrong? How do I remove the cord retractor to get to the two screws that hold the back of the canopy cover?


Your problem is probably is you don't have a proper seal in your chasis. A vacuum has to be sealed tight or the air will leak out and the seal broken. Check around the whole body after the bag is in and check for any airflow noise. I could help more ... Vacuums

I need to remove the top cover from a Wertheim w4030, I have removed all screws that I can get at. I have notice a further 3 in places that is not possible to access. It looks as though the two buttons on the top if removed will provide the solution but I don't want to break anything by forcing something that is not supposed to be done. Can you help?


... Vacuums

I have a Hoover U5111-900 that, every time I attempt to use it, shoots everything it should be sucking up, back out toward my feet. I have replaced the bag, pulled out lots of animal hair and such from the area behind the bag, and taken off all parts able to be removed without a screwdriver and pulled out all chunks of hair, dirt, etc. It still keeps shooting everything it should **** up out the back. Is there something I can remove to get the clog out if that's the problem? I'm scared I wil


Hello,\015\012\015\012Although I could not locate info on a U5111900, the link below shows a similiar upright and things to check for clogs. See page 12 and refer to the pages noted.\015\012\015\012 ... Vacuums

Dismantle hoover sc211 . The auto cable rewind does not work and I need to split the machine. I have removed alll visible screws, but there must be some hidden screws at the switch end>


... Hoover Vacuums

Need to remove the clutch on my Dyson DC07 animal and I can't get the clutch cover off. All the videos look like it should come off easy after removing the three screws.


... Vacuums

Hoover self propelled bagged windtunnel upright model #U6435-900...how do you remove the green plastic shell cover to get to the part that secures the v belt...we need to secure the bolt and cannot get the area. Brushes and transmission wheel not rotating? thanks


Greetings from GoVacuum,\015\012\015\012Here's a great video repair tutorial that we've put together to try and help you with the repair on your Hoover WindTunnel. I hope that this helps you with your repair. If you found this solution ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I am trying to replace the cable on a Hoover smart cyclone, however after taking all the screws out I can see the cover remains intact Can anyone help?


... Hoover Clean Smart Cyclonic Upright Vacuum

The retracktable power cord on my Panasonic MC-E7103K is jammed inside the machine. Does anyone know how I remove the cover after removing the two visible screws? Brian


... Panasonic Vacuums

Hoover u6632900 the self propelled black plastic piece that the cable attaches to is broken. how do i take the cover off to get to the piece and replace it?


... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

I have a Hoover Telios T5732 with broken cable winder, have purchased a replacement winder unit have loosened 5 screw but still cannot separat the covers . some advice please.


After unscrewing all the screws, try to open it evenly, not more from one side.\015\012check this link, \015\012 ... Hoover Vacuums

How did you remove the top cover to get at the arm for the cable drive? (I don't want to break anything else!)


Turn it over, remove the plate over the brush roll, remove the cover over the intake hose, then there are 2 screws, one on each site, remove them, then using a flat blade, there is a slot on each side, from the bottom, push it in to release it and th ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Cable does not wind in. Hoover Helios 2000. Found the 4 font fixing screws - there must be more at the back. How do you get at them?


The flex is fitted to a spring loaded cord reel.\015\012in side the Telios, chances are the reel is faulty and too expensive to change, either get use to it or buy a new one. sorry ... Vacuums

I have a Dyson DC-17 and the top of the cyclone has hair and other debris jammed in the ports. It has 6 six screws holding the parts together and I can only get access to 4 of the screws. The bottom piece appears to be removable, but I can't figure out how to remove it without damaging it. If I can get this piece off, then I have access to the other 2 screws. Can you tell me how to remove the bottom piece? Thanks in advance.


The instructions on how to dis-assemble your DC-17 are somewhat lengthy and it is quite helpful to have pictures and videos handy while you are doing it. Normally I would give the instructions here, but due to the amount of info that is necessary to ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

U6446-900 the drive cable came off and I need to remove the top cover so I can reattach the cable but I can figure out how to remove the cover


From the underside:\015\0121. remove 4 screws holding agitator cover in place\015\0122. remove 2 screws (black screws) holding hose retainer in place, pull hose out through top\015\0123. remove three screws, 2 long, 1 short holding top cover: short ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

How to dismantle a Miele S 5980 vacuum cleaner. The RESET switch has fallen in and I can't remove the plastic panel to replace it. Neither can I remove the cleaner body to get in from beneath. I have removed 2 screws from the front of the barrel (nozzle end), one screw centre front, two screws towards rear, but there seems to be something else holding the housing together. [email protected]


... Miele Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0810 seconds