Having problems with your Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum ?

I need to change the power cord on a Wind Tunnel 6200. The access is not readily apparent.


Answers :

Repair Help & Product Troubleshooting for Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I need to change the power cord on a Wind Tunnel 6200. The access is not readily apparent.


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Repplacing power cord on Hoover Wind tunnel (not self propelled)


I am thinking that the cord goes in on the back, just below the handle. Remove the handle, then from the front, remove the tool holder(#8), then you can get to where the cord comes in and hooks up.\015\012\015\012 ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

I have a Hoover Wind-tunnel Vaccum (Model U5433-900) that needs a new power cord. I am looking for step by step directions for replacing the power cord


... Hoover Vacuums

Hoover wind tunnel retractable power cord


... Vacuums

Repplacing power cord on Hoover Wind tunnel (not self propelled)


HiThis is HARD and you NEED electrical knowledge and IF NOT UP TO IT YOU COULD CAUSE PROBLEMS TO YOUR SELF AND OTHERS.You do not say what the problem is with the cord.If is it damaged then it needs to be replaced with a new one.and then ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover turbo power 7300 wind tunnel v2 belt change


... Vacuums

Change belts on a Hoover Power Drive Wind Tunnel Series 900 vacuum


Try calling Hoover directly toll free at\015\0121-800-944-9200 M-F 8 AM - 7 PM EST. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Replace power cord Hoover U5757-900 - Hoover Company Wind Tunnel U53019 Upright Vacuum


... Hoover Company Wind Tunnel U53019 Upright Vacuum

Got a Filter Queen Majestic Limited Edition, the one with the high and low power switch, an I have to change the power cord. How can I open the main unit to reach that power cord? Thanks,


First remove the top cap under your handle. \012Then, remove the three screws under the handle. \012remove the rubber cover on the switch\012undo the clamps on the side of the unit\012lift off the chrome cover with the cord on ... Filter Queen Majestic Canister Vacuum

No power to Hoover Wind Tunnel Vacuum


The problem is likely the switch a shot of wd40 should fixed it ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Need to replace power cord on Hoover vacuum.


Remove the dirt container and look for screws. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

How do you change the Hoover wind tunnel belts?


If you turn the vacuum over there will be (4) screws that hold on the base cover for the roller brush. Remove the screws and the cover and you can get to the belt(s). You can get replacement belts here: ... Hoover Company Wind Tunnel U53019 Upright Vacuum

Change the power cord on a Eureka series 3270-3275 vacuum cleaner


... Eureka Vacuums

How to change the V belt on hoover wind tunnel U6435-900 ?


Below I have listed a link to the manual which has instructions and a link to the V belt you need.\015\012\011\011\011\011\011\011Windtunnel Manual ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Changing belts on Hoover wind tunnel U6401


Take off the bottom plate covering the brush roll, 4 screws. There are 2 belts, if you replace both, put the V belt on 1st, then stretch the flat belt over the motor shaft, then over the bigger pulley along side the V belt.\015\012\015\0 ... Vacuums

I have my vacume electrical cord tangled inside and disconnected (I can see the open end of the connection from the power cord collector wheel! I need to take the vacume apart so get access to the wire inside. I need to know if there is something else to open other than the 4 screws. Your help is highly appreciated in advance.


Since you did not provide a model number for your vacuum, it is difficult to provide any precise directions regarding disassembly.\015\012\015\012However, most vacuum cleaners are fairly straightforward machines, and as long as you unplug ... Vacuums

Using my unit (owned about 6 years - great service so far) it suddenly quit ... no wind down or 'prelude' like whine - growl - etc. -- it just quit running ... suggestions? clear filters? done check power? how check power cord? done help ...


I agree with you having great service because mine only lasted two years. It sounds like the motor just worn out. If you don't smell any burnt electrical then replace the bushing for the motor. Good Luck ... Dirt Devil Reaction Twin Cyclone Upright Vacuum

Power Cord I have a Miele S528 vacuum and it has been acting up lately. I often times have to move the power cable around to get it to work. I am sure it is a loose connection inside the vacuum but I am not sure how to access the inside of the vacuum.


Hi There,Greetings,\012This definitely sound like a cord reel issue to me. This is really the \012only problem that I ever see on a Miele vacuum \012 \012 9 times out of 10 the cord reel needs to be changed. If you purchase\012 ... Miele Filtration Guard S528 Canister Vacuum

Samsung Quiet Storm Canister Vacuum VAC-9049 The motor will not run. Power is on to the motorized rug tool. How can I remove the upper housing to get access to the motor? I have removed the six visible screws, but the housing is restrained at the rear. I suspect there are additional screws under the power switch and cord retractor assembly, but I cannot remove that either. HELP!


Hi Daltm,\015\012Thank you for contacting Fixya. This is Anil.\015\012I understand that you need assistance n opening the Samsung Vaccum VAC-9049 motor. I will be glad to help you with it.\015\012Please go through ... Samsung Quiet Storm 9048R Bagged Canister Vacuum

Can I change the power cord on my Kirby?


Yes you can here is video ... Kirby Sentria 192006 Power Cord

How to remove hoover wind tunnel cord reel?


... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

How to change a belt on a Hoover wind tunnel


It depends largely on the model. Do you know the model number? you can get any hoover replacement belt here:Replacement Hoover Vacuum Belts ... Vacuums

Wind Tunnel U6436-900 power switch is always on. Vacuum will not turn off.


The switch is the problem. if the machine is under it's warrenty take it to your local vac shop if they can do the warrenty. if it's not then you can order the switch and i can walk you through replacing it. you will need to order a switch kit and i ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a Hoover Wind Tunnel, model #U6655-900. I have changed both belts & have cleaned the brush. It is difficult to push and I smell burning rubber. Do you have any suggestions?


The transmission for the self-propelled could be broken. That's the reason it's difficult to push and the smell ... Vacuums

Wispertone 116.29429990 I need help in getting the cover off. The foot retractor pedal for the power cord has screws under it and I am afraid of breaking the it. How do I access the screws under the pedal?


The pedal may be tough but the attached pushrod that disengages the power cord reel ratchet may not be, and is stressed by reddevil6's maneuver. I'd prefer to go after the tabs that retain the pedal's forward end. They are part of the rear cover and ... Kenmore 23313 Whispertone Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0631 seconds