Having problems with your Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum ?
On / Off switch
\015 I am on my second Vacuum in two years and it getsd very limited use as it is only used down in the basement. BOTH had the same problem....the switch in the handle will not activate the on/off switch. When I look at the design I keep thinking, there has to be a better system?? Any ideas or any sort of adjustments or modifications I can make to eliminate this problem? Not sure how you respond, but my e-mail address is: g,[email protected]\015
Had the same problem and found that the interior switch was to stiff and the plastic activator would just pass over it. Solution was to pull the three screws that ho;d the activator switch, pull the interior switch and replace it. This is a lot easier than it sounds.
Repair Help & Product Troubleshooting for Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
The switch doesn't click on and off. When I opened it up I also noted the wires going into the switch were melted off at the switch. Can I order a new switch and the connectors that attach to the switch?
You can order the switch and connectors from http://www.vacpartswarehouse.com/Eureka-4870-Ultra-Smart-Vac-s/1928.htm\015\012Pl ... Eureka Smartvac 4870 Bagged Upright Vacuum
On/off switch we have two of these vacuums at work, and both of there on/off switches dont work too well. its hard to explain, but when u normally turn it on or off theres a little resistance in the switch and you hear a click, with both of ours the switch moves freely back and forth from on to off, no resisntace, no click, and the machine doesnt stay on, or off for that matter. the switch just moves back and forth.
... Eureka 2991AVZ Bagless Upright Cyclonic Vacuum
My Electrolux Epic 6500 SR will not turn off by pressing on the switch button. I took it apart and removed the switch assy. I can maunually turn it off & on by pressing the rocker arm on the switch assy. It appears that the problem is with the big blue operator button, not the switch assy itself. The button does not seem to press down enough to cause the rocker arm to switch. The button has a "U" shaped wire that presses on the rocker arm and it may have some broken plastic details at the b
WOW !!! Finally You are dead on, absolutely 100%.... good work!!!.Get only a genuine new switch button with spring from an AERUS Electrolux dealer and reinstall. Then carefully reassemble the entire body and wiring harness.Con ... Electrolux Epic 6500 Vacuum
We have a dyson dc 07 animal the machine was working fine then switched off after returning to the machine minutes later it wouldnt switch on, i removed on off switch cover and used a short piece of wire across the brown wires flicked the wall switch and it worked, aha i thought faulty switch aquired a new one to no avail and now even the short piece of wire trick doesnt work, has the motor died do you think, it wasnt over heating or making strange noises prior to refusing to work
It could be the motor. I'm having to replace the brushes on my DC 05. It appears that you can only get brushes for the YDK motors in the DYSON, not the Panasonic motor. Which might be saying something about the YDK motors. What happens is that the ca ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum
Hoover Windtunnel On/Off switch will not turn Off...Switch seems to work O.K. when pressed directly but not with handle switch...It will turn on but not off..Cam seems to be intact on switch actuator..How does switch come out? Thanx
Take the handle off, then remove the tool holder, then you can get to the switch. Just has tabs on each side of switch, depress them and push it out. These switches will do this after awhile, replacing them is usually the way to correct the problem ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
On-off switch My problem is finding a source for an on-off switch for an electrolux vacuum sweeper model 2100. I have replaced the broken toggle and now the sweeper turns on but only as long as the outside button is depressed. It appears that the on-off switch itself is broken as the switch does not ''hold'' when the toggle is activated. It seems to return to it's ''off'' setting as soon as the toggle is released. What ''holds'' the switch in its ''on'' position? Does it depend only on the on-
Hi Hugh. The 2100 has a rocker switch under neath the button. it is probably broken, or the button has a worn detent spring. If you would like, I could send you a switch kit with the rocker, button, and detent spring enclosed for around 20 dollars ... Vacuums
Brissel Healthy Home Hepa Vacuum: On/Off Switch works sporadically. Took handle apart and the switch worked for a while. I am wondering if I need to replace the switch? Also the Brush Switch is having similar problems.
Might not be the switch there is a connection on the swivel by the base that likes to fail ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue
Central vac our central vac will not work unless the main vac in the garage is switched on manualy.... its sucking fine but i have to switch it off at the main switch in the garage after i have used it normaly i just plug in the hose and vac away and it switches itself off we have just had cable installed with a fisher guy in the walls do you think that would be the problem thanks a lot
It is possible that the low voltage wiring that controls your central vacuum has been damaged during the cable work. You can check to see if the low voltage relay is working by shorting the two terminals together at the unit. Just disconnect the two ... M&S Systems AirVac AVP1200 Platinum Series Central Vac - 12,000 sq ft Bagged Central System Vacuum
My Dyson DC 24's beater bar switch didn't actuate and the beater bar didn't turn. When I brought it to a certified serviceman he told me that a wire interferred with the switch and all he had to do was move the wire out of the way of the switch. At the time the machine was under warrantee and it didn't cost me anything. Now however, the machine is out of warrantee and the problem has returned. Does anyone know how to access the switch and move the wire out of the way?
Hi- I had the same experience but it turns out there's a small trip switch if you've taken the brush out to clean it, it needs to be reactivated by pressing the small red button to the right of the brush... took me a year to figure this out! Been mea ... Dyson Ball DC24 Bagless Upright Vacuum
Pull chain switch. Pull chain will not switch off light. This is a zing Ear #305 switch. Where can I purchase a new switch?
I have an Easy-Flo central vac unit. The handle on the electric hose has a switch on the handle. With the switch on ''O'' in the center, it's off. On the left, is the ''I'' position. The vacuum runs but the power brush doesn't. On the right is the ''II'' position. The switch won't flip that way. It feels stuck. It feels as if there is something underneath of it that won't let it push that direction. I have the switch out of the handle, but I can't seem to get the actual black casing around the
Switches are not usually designed to be dissembled.I would strongly suggest that you dont take the switch apart. you are better off getting a new one. then if you feel like it you can take the old switch apart and if it dosnt work you still hav ... Vacuums
Hoover Upright Vacuum model U5470-900 - The On/Off switch on the handle does not properly engage the power switch deeper in the handle assembly. It appears to ride over the lower switch and doesn't engage it to operate it. If I play with it, I can get it to maybe turn on the vacuum, but, then the upper handle switch won't turn it off. Our current workaround is to use the power cord for on/off operation.
... Hoover Vacuums
Have a Bissell proheat steamer. Will not heat up. Is there a reset for for heat switch. I beleive just needs reset. The switch, the way that it feels gives me this indication. Switch will not engage and stay switched to on position. J.J.
Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Deep Cleaner Upright Vacuum
My Shop Vac 90L600A is getting electric thru the cord and into the switch, but it doesn't switch on when you toggle the switch from off to on. Is it a bad switch?
Check the othere end of the switch. You may have a brushes problem in the motor. You will have to check the switch while hot - be careful ... Vacuums
I have a Hoover Elite Rewind model #uh71009. We moved recently and it was jostled around and the red power switch popped out. I put it back in but it's stuck; it stays either left or right, it doesnt move back and forth. It appears there may be another piece missing from the power switch...all I have is the red switch and a tiny cylindrical metal tube with a spring on one end. This piece fits into the hole on the red switch. Inside the vacuum itself where this goes, there is quite a large cavity
Switch I have a kenmore 31913 vacuum and the on/off switch appears to be bad. My problem is getting into the switch. How do I open up the handle to get to the switch?
Go to this website\015\012and enter your complete model number in the search field in the upper\015\012right corner of the page. You should be able ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum
The mechanical off/on in the handle is not working with the electrical on/off switch upon removal of the handle you can cut the machine off by hand but after ensuring the the handle is re-placed in the proper position the machine will not turn off so what new handle or is the rocker switch has worn is now to hard for the mechanical switch to operated
Hi there it's SmartAlec from NelsonVacuums.com.au here. You are spot on in your diagnosis however i have fixed heaps of these and i have found no way to tell wether its the ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Kirby Hello, I have a generation 3 kirby- it was working - I turned it off & it will not turn on again - is there a safety switch /reset button or did the on/off switch go out - I have had it 15 years & replaced the switch 1 time - Thanks
You either need a switch or a cord. Check out my troubleshooting link which includes links to do-it-yourself guides and parts.\015\012\015\012 ... Kirby Generation 3 Bagged Upright Vacuum
Dash controls will not switch from normal to defrost or bilevel. buttons light up but no change. 1993 Buick regal. Problem began as no switching during accelleration but would then switch when the engine wasn't pulling the vacuum
Hello this sounds like a vacuum issue to me.The tiny vacuum hose going to heater system is either split or came off there is also a check valve on this vacuum circuit.that could have gone bad.Also the vacuum ball might have a crack in it.But with out ... Vacuums
The switch on our Hoover Windtunnel vacuum cleaner is not working. I have located the replacement part on your website...part#Ho-28161067, I've removed the wires from the switch. Is there any trick to actually removing and replacing the switch itself? It seems to be in there rather tight.
No, follow the directions to replacing the switch and you should be good. if you got the kit then splice the wires and replace them with the wires profied and the wire nuts, you should be good. ... Vacuums
It won't turn on. I have partially disassembled it and have continuity between the power cord (wide blade) and one of the connectors where the switch assembly snaps in. Also, switch is working fine. There is continuity across it, then no continuity across its connectors when the switch is pressed. Not sure what to try next.
\015\012Please provide the make and model. Thanks. ... Vacuums
The handle for my Eureka 5993 AVZ was getting very hot when used. Finally, the wires around the switch melted and now the vacuum will not work. What is wrong? Is the switch bad? The wires only melted in the immediate vicinity of the three-prong switch. Nothing else appears to be wrong; the vacuum worked fine when it was running - except for the handle getting hot. Thank you!
Try cleaning all...\015\012if have sam paoblem need replaced main motor.... ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum
Hoover on off switch won't turn off. I have to unplug the vacuum to stop it. I have dismantled the handle and now I can't get the inditation in the handle to fit over the little silver knob. I saw there was an on/off switch under the handle that is controlled by a piece of the handle. #1 question for the manufacturer is why don't they put the switch on the outside instead of having gimicks that turn it on and off... arghhhhhhhh
Don't know what model you have, but sounds like you will need to replace the switch. As far as your question, you will have to contact the manufacture for an answer. We only provide solutions to your problem and a model number would have helped. ... Vacuums
Our dustbuster (dont' have model number with me-sorry) won't turn off when I pull back on the switch handle. I disassembled the unit and realize that the tab on the switch handle that pulls back on the internal switch handle to turn it off is not strong enough for its simple task. Does B&D have a proper replacement part?
If you can provide a model number, I can check availability of the switch and can either order it for you, or supply the B&D part number and you can order it from most local vacuum shops in your area or from Black & Decker direct online: ... Black & Decker 15.6 Volt DustBuster Vacuum
Hoover power drive u6311 - How do u change switch? Does anyone have any idea how to remove the on and off switch, when I tap on the housing the motot and light goes on and off. Also does somebody have a exploded view of this model. also does anyone know the part number of the switch.
The swrtch is located in the bottom section of the motor. When the swtcih goes out it time to repalce the unit. The swtich is part of the motor. The switch rod run all the way down the body to the swtich located in the motor. ... Hoover U6311-930 Power Drive Bagged Upright Vacuum