Having problems with your Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum ?

How to remove the motor on a hoover windtunnel?

\015 Motor removal\015

Answers :

Repair Help & Product Troubleshooting for Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert


Either the hose has a clog, or the inlet down by the belt is clogged. Is there suction at the end of the hose, if not then it is clogged. If there is suction, then it has to be clogged down below by the brush roll, check that inlet. There also is ... Vacuums

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert


Mine does the same thing. There is no suction. I found that there is a door that opens when you tilt the handle in the down possition. I think there should be a spring in place so it can open. Until I find a replacement spring I have to open the door ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

How to remove the motor on a hoover windtunnel?


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover windtunnel vaccum U6445-900 motor not turning on. I removed the screws and located the contacts inside. There is an on-off switch which seems to be stuck Is there a way to replace this switch


There are a number of Hoover vacuums that are subject to a recall due to an overheating on/off switch. Check out this web site to see if your is included. You'll need the model number and serial number from the back of the unit. The manufacturer w ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover windtunnel motor is running rough and overheating, even after clearing the hoses and removing the belts. Could there be something jammed in the blower? How do I get in there to clean it out?


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hoover windtunnel hose removal - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Replace motor hoover windtunnel - Hoover U6476-910 WindTunnel Upright Vacuum Cleaner Bagged Vacuum


... Hoover U6476-910 WindTunnel Upright Vacuum Cleaner Bagged Vacuum

Hoover WindTunnel Canister: Roller brush motor not turning


These motors have a fuse incorporated in the field winding and it sounds like that blew. These motors sometimes overheat at the front bearing and the bearing will melt into the plastic housing. This will cause the fuse to blow. It sounds like that's ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Smoke from Hoover Savvy U8185-900. Looks to be from the Motor assembly U8174-900. How to access motor in order to verify condition, have already removed all screws, but unabale to expoxe motor..


... Hoover U8185-900 Upright Vacuum

My Hoover Windtunnel Ultra U6425-900 began shutting off after a few minutes of vacuuming. The time interval became shorter and shorter. If I leave it sit a while, it will start again. This does not happen when I used the attachments - only with the floor brushes. The switch has recently been replaced and the whole vacuum serviced by a Hoover dealer about a year ago. I have been told by a local repair shop(not a Hoover dealer) that it is the motor, there is nothing to do other than replace t


... Hoover Vacuums

How do you remove the Handle from the Hoover Windtunnel Deluxe to replace the switch?


Removing the handle assembly should be easy after removal of the two screws. It may be binding or hanging up on the self-propel cable...or the plastic may just be stuck/binding. Note that the handle slides in and out of the vacuum unit along the sa ... Hoover U5450-900 Windtunnel Supreme Bagged Upright Vacuum

I have a Hoover V2 Windtunnel and the brushes are not turning. I have removed the black plate, removed the 4 brushes, now what?


Check for hair / fibre lodged in machine and brushes, remove it then re-assemble ... Hoover F7220900 SteamVac V2 Upright Vacuum

The switch on our Hoover Windtunnel vacuum cleaner is not working. I have located the replacement part on your website...part#Ho-28161067, I've removed the wires from the switch. Is there any trick to actually removing and replacing the switch itself? It seems to be in there rather tight.


No, follow the directions to replacing the switch and you should be good. if you got the kit then splice the wires and replace them with the wires profied and the wire nuts, you should be good. ... Vacuums

Hi On a Hoover convertable model U4497-900 I'm trying to replace the fan. The old fan cracked, then flew apart. I have the new fan, have the motor assembly removed, but can't seem to get the pulley nut off the motor to replace the fan. Is there a trick to this or should I just try to muscle it? Thanks.


... Vacuums

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.


The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

How to remove broken handle release on hoover windtunnel upright


... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

How to Remove Hoover Windtunnel Main Body


... Hoover S3639 WindTunnel Bagged Canister Vacuum

I need help in disasembling my hoover windtunnel to check the motor brushes


... Hoover Vacuums

Hoover UH70210 Windtunnel PAWS motor high pitch noise


... Hoover UH70210 Bagless Upright Vacuum

How to remove brushes on hoover 7300 windtunnel v2 vacuum


... Hoover Vacuums

How to remove the hoover windtunnel handle release lever


Tilt the handle back and pry it out with a flat blade screwdriver. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have a hoover windtunnel u5757-900 and the motor stops in the mittle of the operation, no restrictions


When the motor stops, this is usually caused by an restriction in air flow...caused by a full bag, dirty filter or blockage. do you wait for about 30 minuites and it you can turn it on again? have you changed th dirt cup filter in the last 2 years? h ... Vacuums

I have a Hoover Windtunnel Farrington upright model U6431-900 It has worked flawlessly until last week. The roller brush has stopped turning and I believe it is the belt that has broken but I am not sure how to remove the cover to inspect it and replace the belt if that is the problem. Please inform me how to perform the operation and what I should I look for? Is there a site with a diagram on how to replace said parts? Thanks for any and all helpful info that you can supply me with. Larry


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=783264\015\012Generic problem for all Vacuums\015\012I have a Hoover WindTunnel\015\012Posted by ... Vacuums

Hoover canister vacuum (windtunnel)- turned it on and it had good suction, then smoke came out and it smells like something is burning. Is it the motor burning up or something else?


Probably the belt..\015\012Turn it over so the bottom is facing up..\015\012Remove the plate that surounds the brush..\015\012Check to se if brush is spinning frely and that the belt is on there poroper ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hoover windtunnel vacuum roller brush doesn't turn. Have removed hair and lubed and belt looks ok. Any ideas?


Does the motor turn?  if it does replace the belt. ... Hoover Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0558 seconds