Having problems with your Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum ?

Hoover windtunnel vacum..belt is rotating..brush is not..plus belt keep coming off

\015 Can I repair myself...what is the solution...where do I get it from?\015

Answers :

More than likely, there is hair or fibres caught up in the bearings binding them. There are usually 2 screws you can remove on the bottom of the vaccume that allow you to remove the plate. The back part of the plate usually locks in with tabs. Remove the plate, then pull out the brush. The bearing will come out of slots. Remove the bearings, and more than likely you will find hair or fibers wrapped around the shaft on each end of the roller. Remove the material, reinstall the bearings, roller and plate and you should be good to go! :)
Repair Help & Product Troubleshooting for Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Windtunnel belt I have a new Hoover Windtunnel canister. The belt keeps coming off. It happened a couple weeks ago (several times after putting the belt back on) so I assumed I might need a new belt as it might have dried out at the store. I ordered new belts and today I used it for about an hour and the belt came off again, twice. There doesn't seem to be anything to hold the belt on the stem as it seems to slip off. I have tried it centered, to the left and to the right....can you help. I am v


I've successfully used a compatible belt - Royal 104425001 .It's still new, but for the time being at least - it works. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Hoover Windtunnel - the belt keeps coming off & it is the correct


One compatible belt that I use and works (at least while its new) is Royal 104425001. Try that. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Hoover windtunnel vacum..belt is rotating..brush is not..plus belt keep coming off


More than likely, there is hair or fibres caught up in the bearings binding them. There are usually 2 screws you can remove on the bottom of the vaccume that allow you to remove the plate. The back part of the plate usually locks in with tabs. Remove ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

HOOVER WINDTUNNEL VACUUM MODEL U6454-900 BELT KEEPS COMING OFF


Have you put on a new belt or just keep using the old one. If you haven't replaced it in the last 6 months, then it has stretched to the point where it won't stay on. Another cause is catching throw rugs, towels or something that gets in there and ... Hoover Vacuums

Is there any way to repair or replace the belt GUIDE on the inside of the belt compartment of a '97 Hoover Wind Tunnel (not self-propelled)? It became twisted when a belt broke and now the belt rubs against it and sounds really weird, and I'm sure new belts will continue to break.. This guide is a long piece of molded material (part of the compartent wall) to keep the belt from coming off the pulley. It also had a sort of metal clip on it. It was loose and I took it off because of the way the pa


Honestly you should take it to a vac.shop they can fix any vac. ... Windsor SR12 Sensor Bagged Upright Vacuum

Drive belt keeps breaking on hoover windtunnel vacuum. Drive belt won't turn the agitator. Belt is new. Small belt is new. Agitator is new.


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hoover Self Propelled Wind Tunnel. Keeps throwing off drive belt. New belt. Starts up fine, as soon as you release and lower handle, belt comes off spindle


Hi, it sounds as though that when you release the handle, I no this puts pressure on the brush or spindle, this is causing the belt to come off. You need to remove the roller brush and check it for any thing that may have rapped around it causing it ... Vacuums

Hoover Windtunnel Hello! I had to change the flat belt on my vaccum and now the belt won't stay on. I can replace it, use the vaccum, then the next time the belt comes off. Is there something I did not do right? Thanks for your help! Jennfer


Your belt may be twisted inside-out. Be sure the printed marks on the belt face away from the pulleys and shaft. The printing should face you. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover elite rewind belt keeps coming off - Hoover Vacuums


... Hoover Vacuums

Hoover Wind Tunnel - Belt Keeps Coming Off


This is the same problem I had. We took it to a vacuum repair store and they fixed it for $80.00!! It lasted about 6 months and it just happened again. I'm not spending the money - I'm looking for another vacuum cleaner. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

The belt on my Hoover Elite Rewind UH71003 keeps coming off.


Those machines come half way across the world. The belt stretches while it waits. Buy a new belt for it and you'll be good as new.. actually better. Here's a full length description of why. http://www.vacuummedic.com/blog/2012/10/09/my-br ... Hoover Elite Rewind Pet Bagless Upright, UH71003

Hoover u6616-900 WindTunnel, belts come off system.


In order to seperate the hood from the agitator housing you will need to remove the screws for the bottom plate (4) remove the plate. next you will see (2) screws. one will be by the belt side the other is on the other side by the sucktion inlet. onc ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

Hoover U6634-900 self propelled, brush belt keeps coming off.


Unfourtunatly it could be the height of your carpet also using on area rugs could cause it to do that too. check the brush roll and make sure it is spinning freely. ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

I have a Hoover U5750-900 Windtunnel Bagless and For some reason, the belt has been replaced correctly, but there is a very LOUD vibration/rattling coming from the agitator, like it's hitting the assembly/bottom plate? Is there a reason that there would not be enough distance from the plate?


... Hoover U5750-900 WindTunnel Bagless Upright Vacuum

Hoover windtunnel t series belt keeps falling off


... Hoover Vacuums

Good Morning, A friend recently gave me her Hoover windtunnel model U630-900 vacuum. It is a self propelled vac. It comes on but is hard to push and will not really pick up any dust particles on the carpet. It has a funny smell also. I saw where one of you Q & A you said to check the roller brush. I thought maybe a belt may be off or something, but I do not have a manual to know where to begin checking. Could you tell what to check and also if there is anywhere online to download the manua


... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

Need help with Hoover S3765-040 WindTunnel Electronic Bagless Canister Vacuum. The belt that rotates the brush keeps slipping off. what to do?


The belt could be stretched and that could be causing the slip. Or you could have the wrong belt if you've replaced it recently ... Vacuums

I have a Hoover WindTunnel Bagless Vacuum Cleaner, Model #U5753-900, Serial number 110600215585, which I purchased from Loew's on 3/31/07. With it, came a Hoove Slider for hard floor surfaces, Model #S2105, Serial number 050500084989. The Slider strted making a noise--I thought something had been caught in the roller, but discovered, it had not; so I and my husband proceeded to take the Slider apart. I believe one of the belts had come off; but when we took the screws off the bottom to check


... Vacuums

On several occasions the belt has come off the Hoover Windtunnel beater shaft and had to be re-installed. Is there any way to prevent it from slipping off? The shaft seems to be made so that the middle if it is wider(thicker than either the end or the part closer to the motor, which, to me, is a bad design so I don't know how to overcome this problem. I'd be very grateful for a permanent solution to this problem. Thanks in Advance, mas


Your belt is stretched and needs replacement ( # 38528035 ) . The agitator is crowned so that the belt stays centered. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

V-belt flapping on Hoover Self-Propelled WindTunnel Bagged Vacuum


... Hoover U6441-940 WindTunnel Bagged Upright Vacuum

Hoover WindTunnel Self-Propelled V Belt


I had this same problem with the V belt on my Hoover Vaccuum.\012\012There are three (3) basic things that will cause the brush roll not to spin.\012\0121. When handle is upright, brush roll is OFF.\0122. When switch is set for HARD surfa ... Hoover U6441-940 WindTunnel Bagged Upright Vacuum

Belt keeps coming off


Great. Glad to help.\015\012\015\012If you would, take a moment to rate this solution. Thank you. Happy vacuuming. :-) ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover Windtunnel Bagged upright vacuum is smoking and belt is slitting and burning


You probably need to replace your brushroll seeing that your belt is burning means motor is turning. first check you brushroll and see if there is an obstruction keeping it from spinning if its not spinning freely replace ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

The belt keeps coming off. There is a little U shaped metal piece that came off when the belt first came off. Where does it go? When we first got the vacuum, we sucked something up and the belt came off and that little metal piece fell out. The belt now periodically comes off when we bump something. Please help us!!!!!!!!!!!!


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have a Hoover Slider, Model #S2105, Serial #050500084989, and I need instructions on putting it back together; with parts and assembly of parts. I took it apart because it was making a noise, and I believe one of the belts had come off. However, when I took the screws out of the bottom to check the belts, the whole thing fell apart. Now I can't get back together properly. It will not come on, and I believe it is because the switch that makes it come on when you lower the handle is not posi


Greetings from GoVacuum,\015\012\015\012Please see the link below for a parts schematic to your Hoover Slider, hopefully this will help you put the machine back together. If you find a part that is missing, and would like to order one, j ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0719 seconds