Having problems with your Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum ?

Why is my Hoover self propel vacuum brush not spining


Answers :

Repair Help & Product Troubleshooting for Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Why is my Hoover self propel vacuum brush not spining


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Just replaced the belts on my Hoover Windtunnel II self-propelled vacuum. The brushes are now turning ok, but the self propelled feature is not working. Squeals when when you lock it in the upright position.


Check the plastic part, which the the self propelled cable is attached to. (release the handle, tilt it back. You should be able to see the cable attached by a screw to a black plastic arm.) It is either broken or the cable is lose. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Folks, My wife and I own a three-year-old Hoover U6434-900 self-propelled "Wind Tunnel" upright vacuum cleaner. The problem is that, even on the highest setting (front-end as high as possible), it gets bogged-down in even shallow pile carpet to the point that the brush stops. I've cleaned the machine thoroughly, pulling hair, thread, dental floss and such from the brush (and everywhere else), including unscrewing the brush end caps and pulling out the cat hair mats which formed in there.


Check to see if the V belt sits too deep in the brushroll groove, if it sits too deep you will need to replace the brushroll. the top of the belt should be about flush with the brushroll. also you have to take the screws out of the self propelled uni ... Vacuums

I have a Hoover Wind Tunnel Self-propelled vacuum. I changed the belts because the brush was not turning. After replacing the belts the brush is still not turning what can be wrong?


There are two belts on the wind tunnel this video will show you how to repair ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

V-belt flapping on Hoover Self-Propelled WindTunnel Bagged Vacuum


... Hoover U6441-940 WindTunnel Bagged Upright Vacuum

Where can I find roller brush for Hoover U6311-930 Power Drive Self Propelled vacuum


... Hoover U6311-930 Power Drive Bagged Upright Vacuum

Hoover windtunnel self propelled vacuum has new belts but brush won't turn on carpet


... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Good Morning, A friend recently gave me her Hoover windtunnel model U630-900 vacuum. It is a self propelled vac. It comes on but is hard to push and will not really pick up any dust particles on the carpet. It has a funny smell also. I saw where one of you Q & A you said to check the roller brush. I thought maybe a belt may be off or something, but I do not have a manual to know where to begin checking. Could you tell what to check and also if there is anywhere online to download the manua


... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

How do I get the old V-belt off of my Hoover Platinum Self-propelled vacuum UH70015, so that I can replace it. I already have the brush off


... Hoover UH70015 Bagless Upright Cyclonic Vacuum

I have 2 Hoover Wind Tunnel-self propelled bagged vacuums-U6433-900 model.The roller bar does not agitate, the self propelled feature does not work and, in general, the vacuum is not performing well. I have replaced the roller bar, the v belt and the wide belt. The filters have been replaced and it has a new bag. I have had both of these since 2004 and they were fairly expensive $200 each) but if the repairs are prohibitive, I might as well get new vacuums. Suggestions? I just spent $100 for bel


The Hoover WindTunnel self propelled is a machine that we see in our retail stores (Vacuums Unlimited) constantly. The benefit of having a supposed "self-propelled" machine wears of quickly after the numerous time you will need to take this machine ... Hoover Vacuums

I have hoover WindTunnel Self Propelled Vacuum


Greetings from GoVacuum,Here's a great video repair tutorial that we've put together to try and help you with the repair on your Hoover WindTunnel. I hope that this helps you with your repair. If you found this ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.


... Hoover U6485900 Bagged Upright Vacuum

Hoover Upright Bagless WindTunnel does not self propel (U6625-900). Belts are new, Brush turns strongly. Wheels propel forward very weakly and do not reverse when the handle is pulled backward. Is there a mechanical link from the self propel switch to the "transmission" ? Are there any gears that could be worn or not engaging properly?


... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Hoover upright self-propelled drive vacuum cleaner u6331-93 will not self-propel


Here is a video how to fix ... Vacuums

Self propell doesn't work. Motor spins and belt burns, brushes do not turn. model Hoover self propelled u6425-900


May be a stripped sprocket/cog or snapped shaft. check and replace as needed. ... Hoover Vacuums

I have a Hoover power max self propelled vacuum. The belt that goes to the self propelled part keeps slipping off. I've had the belt replaced, but the problem persists. What can be wrong? I've taken it to a Sew N Vac repair, but all he did was replace the belt again. And it still has the same problem.


I can guess of one problembelt gets removed when motor is running right?am assuming that belt is fit tightly and fits correctly when motor is in restif so then ur motor is not running at a proper speed which can be a pos ... Vacuums

Installing belt on hoover self propelled upright vacuum


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=40544&thid=641399\015\012Installing belt on Hoover self propelled upright...\015\012Posted by Fryeburger on Jun 02, 2008 ... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

Hoover WindTunnel Self-Propelled V Belt


I had this same problem with the V belt on my Hoover Vaccuum.\012\012There are three (3) basic things that will cause the brush roll not to spin.\012\0121. When handle is upright, brush roll is OFF.\0122. When switch is set for HARD surfa ... Hoover U6441-940 WindTunnel Bagged Upright Vacuum

Hoover wind tunnel upright self propelled. U6473-900. Brush does not work. Heard it was a 'brush controller' problem and can be fixed. Please tell me how.


Most likely the flat belt has stretched enough so as to not turn the pulley that in turn turns the brush roll using a V belt. Also there is a small idler wheel, if hook up, then it won't engage the V belt. ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

I own a self-propelled Hoover Wind Tunnel vacuum cleaner (Model U6425-920). I do now have an owner's manual and was wondering how to clean the Hepa filter on this model (*this model uses a vacuum cleaner bag also).


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=794479\015\012Generic problem for all Vacuums\015\012I own a self-propelled Hoover\015\012Posted by goh ... Vacuums

Hoover U6445-900 bagged self propelled Mach 6.9 brush will not turn, replaced belts, not the problem....housing cover seems loose & when manifulated the belt brush will turn. Any ideas on what the problem could be? Thanks!


... Hoover U6446-900 WindTunnel Bagged Upright Vacuum

Hoover 6634900 self propel will not work. - Hoover Vacuums


The hoover series sometimes has a belt driven gear or a plastic gear assembly that gets worn out. You may have to replace one or the other to see if this does the trick. Becareful not to loose the little screws that holds the assembly in place. Some ... Hoover Vacuums

Hoover self propelled vacuum not working


... Hoover Vacuums

Hoover windtunnel Self-propelled - brush roll stops


There is a idler wheel that will drive the V belt, sometimes they jam and you just have to reach in, push and make sure if comes in contact with the belt. Alot of times tho it is the other flat belt, 38528035 that will stretch and can cause you to h ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Brush won't turn and self propel doesn't work


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=40485&thid=619779\015\012Brush won't turn and self propel doesn't work (by 2 users)\015\012Posted by brucelk on May 24, 2008 ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1263 seconds