Having problems with your Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum ?

Vacuum is not self-propelling and no suction

\015 Hoover wind-tunne: turns on just doesn't move or **** any suggestions? I am not sure if the product I listed is the exact one i have.. I just know it is a windtunnel and bagged.\015

Answers :

If you haven't replaced the flat belt in several months, then it has stretched and can't turn the brush roll under load. Check the brush roll, make sure the ends turn freely, if not, replace it. Check to see if the drive cable hasn't broken also the drive actuator arm, alot of times it breaks off where the cable attaches to it. If you watch the cable down below, pull the handle up and down to see what the cable is doing or not doing.
Replace your rubber belt, it is what powers the self-propel mechanism.
\015\012Remove the 4 screws from the baseplate and replace the belt at the rear of the machine.
Repair Help & Product Troubleshooting for Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bag was not on good, resulted in dust,dirt, dog hair everywhere...have cleaned pretty thoroughly but vacuum does not have any suction. After taking apart did find that the larger wide belt is broke but I think that just affects the self propel...is there a belt tied to suction? HELP!

Greetings from GoVacuum,\015\012\015\012There are two things that you should check on this vacuum after running it without a bag inside. The first thing you should check is the filter that is underneath of the vacuum bag. This filter i ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Vacuum is not self-propelling and no suction

If you haven't replaced the flat belt in several months, then it has stretched and can't turn the brush roll under load. Check the brush roll, make sure the ends turn freely, if not, replace it. Check to see if the drive cable hasn't broken also t ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover windtunnel self-propelled vacuum is not suctioning, changed belts, new bag what is the problem and i have checked the hose.

Have you cleaned the filters? ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

On my hover U6616-900 the self propell work fine on the med setting on med height carpet, but when I go to low height carpet and height set on med the self propell does not pull the vacuum and it is hard to push. Also if I raise the height to the highest setting the self propell works correctly and appears to clen. Any ideas? S/N 090400184555, think this vacuum is maybe 5 years old and my wife uses it lots. Should I think of maybe a complete overhaul or a replacement at this time?

This is a typical problem you are describing. I would recommend you change the belts, this will resolve the "hard to push" and most likely resove your issues. based on the s/n given you maching was made on sept 2004. ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

I have 2 Hoover Wind Tunnel-self propelled bagged vacuums-U6433-900 model.The roller bar does not agitate, the self propelled feature does not work and, in general, the vacuum is not performing well. I have replaced the roller bar, the v belt and the wide belt. The filters have been replaced and it has a new bag. I have had both of these since 2004 and they were fairly expensive $200 each) but if the repairs are prohibitive, I might as well get new vacuums. Suggestions? I just spent $100 for bel

The Hoover WindTunnel self propelled is a machine that we see in our retail stores (Vacuums Unlimited) constantly. The benefit of having a supposed "self-propelled" machine wears of quickly after the numerous time you will need to take this machine ... Hoover Vacuums

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.

... Hoover U6485900 Bagged Upright Vacuum

I have a Dirt Devil Vision self-propelled vacuum cleaner. Recently, the self-propelled feature is stuck in the backward mode, so it only goes backwards! I can get it to go forward if I push really hard (i guess it is good for a workout!). I try to turn off the propel feature completely, but it will not turn off. please help!

Hi, the problem you are having is going to be with the switch that controls the forwards and backwards settings so with this stuck in backwards their is no way you can get this turned off, the other problem is your not going to be able to replace thi ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

I purchased a brand new Eureka Pet vacuum, sorry don't know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage

If the motor is running, there should be suction. Possible problems depend on whether it's a canister or upright and are:\015\012A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out ... Eureka Vacuums

Hoover upright self-propelled drive vacuum cleaner u6331-93 will not self-propel

Here is a video how to fix ... Vacuums

Just replaced the belts on my Hoover Windtunnel II self-propelled vacuum. The brushes are now turning ok, but the self propelled feature is not working. Squeals when when you lock it in the upright position.

Check the plastic part, which the the self propelled cable is attached to. (release the handle, tilt it back. You should be able to see the cable attached by a screw to a black plastic arm.) It is either broken or the cable is lose. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

My self-propelled Heritage II Kirby vacuum is no long self-propelled.

Her2 was not self propelled ... Kirby Heritage II Vacuum

Self Propel The vacuum will not work in a self propelled mode.

Me again with more info. This happened to me and I solved it as described previously. More info here:There's a microswitch located where the hose attaches to the bottom section of the vacuum. If the hose is not completely inserted, th ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

How to disassemble self propelled vacuum to repair level that turns on self propelled mechanism

... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have a Hoover power max self propelled vacuum. The belt that goes to the self propelled part keeps slipping off. I've had the belt replaced, but the problem persists. What can be wrong? I've taken it to a Sew N Vac repair, but all he did was replace the belt again. And it still has the same problem.

I can guess of one problembelt gets removed when motor is running right?am assuming that belt is fit tightly and fits correctly when motor is in restif so then ur motor is not running at a proper speed which can be a pos ... Vacuums

Self-propelled Broken? Vacuum very hard to push. Self -propelled doesn't seem too be working. What can I do?

I have the same problem, found out there is a cable that is broken, I'm trying to figure out how to fix it. ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Loss os self propel and suction??

Mine does the same thing. There is no suction. I found that there is a door that opens when you tilt the handle in the down possition. I think there should be a spring in place so it can open. Until I find a replacement spring I have to open the ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have a self propelled Power Supreme vacuum. It

Most common cause is fibre / hair in the roller and brushes. remove base cover and remove fibres . Remove screws and use small scissors to cut along roller / brush then pull gently. ... Vacuums

My Hoover U6311-930 has lost suction and self propelled. What can I do?

... Hoover U6311-930 Power Drive Bagged Upright Vacuum

V-belt flapping on Hoover Self-Propelled WindTunnel Bagged Vacuum

... Hoover U6441-940 WindTunnel Bagged Upright Vacuum

I have hoover WindTunnel Self Propelled Vacuum

Greetings from GoVacuum,Here's a great video repair tutorial that we've put together to try and help you with the repair on your Hoover WindTunnel. I hope that this helps you with your repair. If you found this ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Installing belt on hoover self propelled upright vacuum

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=40544&thid=641399\015\012Installing belt on Hoover self propelled upright...\015\012Posted by Fryeburger on Jun 02, 2008 ... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

I own a self-propelled Hoover Wind Tunnel vacuum cleaner (Model U6425-920). I do now have an owner's manual and was wondering how to clean the Hepa filter on this model (*this model uses a vacuum cleaner bag also).

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=794479\015\012Generic problem for all Vacuums\015\012I own a self-propelled Hoover\015\012Posted by goh ... Vacuums

I have a Hoover Wind Tunnel Self propelled 12amp. There seems to be very little suction. I have cleaned the hoses and filters but still not much suction. any ideas? thanks.

I have the same problem , and Like the the person who asked the Question ,, there is no Blockage ,, Im thinking maybe these filters have a very short life span ,, and even cleaning theses filters with a brush, etc , may not be enough, and could have ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Kenmore direct drive will no longer self-propell

There may also be a reset button. If the brushes get stuck the unit can shut off power to the brushes to keep a total melt down from occurring. The reset button should return power in these types of vacuums. ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Hoover self propelled vacuum not working

... Hoover Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.2578 seconds