Having problems with your Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum ?

Hoover Windtunnel carpet level adjustment

\015 When I try to vacuum my oriental rugs (with the mat beneath) the vacuum is very difficult to push forward and seems to be grabbing the rug. It seems to vacuum okay on hard surfaces and regular carpet. The lever for the carpet height adjustment doesn't seem to have any effect. I haven't seen any problems addressed concerning this part of the machine. Does anyone know if this is a common problem and what the solution would be? Any help or suggestions is appreciated.\015

Answers :

The suction is so great that it sucks up your carpet, then nothing works. I get my children to stand on the corners/edges of the rug so that it stays perfectly flat on the floor while I vacuum. Or, you can turn off the brush roller (set it to "hard floor" setting). Or, tip the vacuum cleaner's front up slightly while vacuuming, to reduce suction.
Repair Help & Product Troubleshooting for Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover Windtunnel carpet level adjustment

The suction is so great that it sucks up your carpet, then nothing works. I get my children to stand on the corners/edges of the rug so that it stays perfectly flat on the floor while I vacuum. Or, you can turn off the brush roller (set it to "har ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover Windtunnel smells like burnt rubber replaced belts brush doesn't spin when placed on carpet height adjustments won't move

Sounds like you have a bad brush roll(48414115), take it out and see the the ends turn freely or not, if not, then replace it. Also check the the slots that the brush roll sits in to make sure they haven't melted. I am assuming that the ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

I have a WindTunnel Hoover vacuumn that is less than 1 year old. The on-off switch is worn out and the carpet height adjuster does not connect. Where is my closest service center? (So I can use my warranty) My zipcode is 58203. My phone number is: 1-201-791-3492. My email address is: [email protected] Of course, I need help as soon as possible. Thank you, Audrey Cooper

According to Hoover's web site the closest service center is \015\012\015\012\015\012\015\012MJB MAYTAG HOME APPL CENTER \015\012418 BELTRAMI AVE NWBEMIDJI MN 56601 218-751-2420\015\012which appears to be over 100 miles from you. I have ... Hoover Vacuums

I have a Hoover Windtunnel Model #U5456-900 that appears t be stuck in the lowest postion. When I take apart the brush assembly, I do not see anything that the sliding level moves to adjust the height. Can you help?

... Hoover Vacuums

Height adjustment on Hoover Windtunnel u5755-900 no longer works

On this model it is only a single slide adjustment lever. have you trie to tilt the vac backwards (lifting the wieght off the front wheels) and then slide the adjustment lever?\015\012\015\012If there is a mechanical issue with it. take t ... Hoover Vacuums

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.

... Hoover U6485900 Bagged Upright Vacuum

On our new carpet (which is not that thick but thicker than the old) I can't set the carpet thickness high enough. The suction really grabs the carpet and bogs down my self-propelled wind-tunnel Hoover. I then have to push down on the handle to tilt the front up. The thickness setting is as high as it will go. Is there some way that I can further adjust this. The machine is about eight years old.

I can help you out only if you will let me know the front width of the machine. Alongwith the height which you wan't to give raise. KIndly give the width and elevation in cms. ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

My Hoover Windtunnel does not clean carpet. The machine keeps grabbing the carpet. It appears that even with the switch set for carpet, the machine keeps acting as though it were set for a hard floor. How can I fix it?

Move the height adjustment up a little ... Hoover U6476-900 WindTunnel Vacuum

How do you reattach the front rollers on hoover elite rewind so that the carpet height adjustment works

... Hoover Vacuums

Canister powerhead brush does not seem to spin when the carpet level adjustment is on any level other than "high". Could it be something as simple as needing a new belt and is there a difference in a regular belt as opposed to "whisper belt"?

The belt is worn/stretched to the point that it cannot take the load on low level setting due to more resistance against the carpet and there is also no signifagant difference between the two belts except for expecting a longer belt life from the whi ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Hoover Windtunnel U5750-900 Agitator brush is weak. It turns fine if I tilt the vacuum back, but it slows to almost 1/4 speed when it touches carpet, even on the highest carpet setting. I've replaced the agitator belt twice. The brush used to turn powerfully even on the lowest (Hard Floor) setting. Ideas? I should probably lube the agitator brush ball bearings, and re-check the belt, but, other than that, I'm stumped.

... Hoover U5750-900 WindTunnel Bagless Upright Vacuum

Hoover windtunnel Not sure of model number- but brush roller clamps down on carpet being vacuumed and stops spinning regardless of which of the 3 height selections is selected. Can make it work by leveraging the handle down (or back towards me) to keep the cleaning head a little off of the carpet-any suggestions or ideas?

Would suggest the drive belt is stretched and thus is slipping when contact is made with the carpet. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.

The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

I have Hoover WindTunnel Air Upright Vacuum - UH70400 just used couple of times. While vacuuming the carpet carpet fringes were rolled up in to brushroll and brushrol stopped working. It means vacuum is not working effectively now. Brushroll indicator is flickering.

... Hoover Vacuums

Hoover Windtunnel My Hoover is about a year old and now it's not as easy to push, when I first bought it, it would almost glide over the carpet, now it can be a bit of a struggle to push it around. Any ideas why?

The gears inside might be worn down. ... Hoover U8147-900 WindTunnel V2 Bagless Upright Cyclonic Vacuum

Dyson 28 airmuscle... carpet level selectors will not stop blinking... I have tried all selectors to see if an adjustment helps It has not lost section but the blinking light tells me something is up... I have two vaccumes one for upstairs and one for downstairs. all same carpet in the house and I use the medium pile and only one of the vaccumes is having this problem

... Dyson Vacuums

How is the V-belt tension adjusted (Hoover Model U6439-900)or how do I know if the tension is correct? There seems to be a lot of "play" in the belt and I'm wondering if that is the reason the brush roll only turns as the wheels turn, regardless of the carpet height setting. And yes, the brush roll is set for carpet, not hard floor. Or is the cause of the problem something other than the V-belt? A new flat belt was installed when the machine was professionally serviced so I assume (?) that was a

The V-Belt is not adjustable. There are two ways the belt has no tension: (1) when the handle is upright, a mechanical lever takes the drive tension off the belt, and (2) the brush roll lever setting you described. The upper handle would have to be ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover Wind Tunnel Bagless problem with carpet hight adjustment

Hi There Alec from VacuumSpot here. Most of these machines don't actually change the height until the handle is lowered so even though you change the dial when it is an up ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Height adjustment won't work on Hoover windtunnel

In my experience, Hoover height adjustment are "stops" rather than being attached to an axel. Look for something that rould resemble a set of circular steps somewhere in the path the axel would take as it goes up and down. It is usually on the unde ... Vacuums

Hoover u6476 Windtunnel nozzle height adjustment cam repair

... Vacuums

My hoover windtunnel will not switch to carpet mode

... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Can you help with this Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum ... hard to move on carpet

... Vacuums

Hoover u6476 Windtunnel nozzle height adjustment cam repair

... Hoover Vacuums

Hoover WindTunnel Self-Propelled V Belt

I had this same problem with the V belt on my Hoover Vaccuum.\012\012There are three (3) basic things that will cause the brush roll not to spin.\012\0121. When handle is upright, brush roll is OFF.\0122. When switch is set for HARD surfa ... Hoover U6441-940 WindTunnel Bagged Upright Vacuum

Hoover windtunnel cannister - can't disconnect carpet attachment

... Vapor WhiteWing Steamer Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0670 seconds