Having problems with your Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum ?
Can't get it from Roller Brush Off to Roller Brush On
\015 Mine is actually the Hoover U6485-900 Windtunnel Anniversary Bagged Upright.\015\012\015\012It constantly stays in the Roller Brush Off. I have changed the settings for carpet height and from floor to carpet and back and forth and it never changes. How do I get it to go to Roller Brush On?\015
On some model there is also a plastic tab to unlock the roller brush, check it out. You must also have the right tool installed.
There is a user manual for Hoover U6485-900 ---
Repair Help & Product Troubleshooting for Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Tried to take roller brush out to clean it's housing, cant get one side back in without trying to force it.
The roller brush fits snug in the housing, however, if you had it out, check to make sure the end caps of the brush shaft are pushed all the way on. These just slide on the roller bar shaft and if something got under them, they would not be able to ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Can't get it from Roller Brush Off to Roller Brush On
On some model there is also a plastic tab to unlock the roller brush, check it out. You must also have the right tool installed. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Hoover Mach 6 U5198-900 vacuum roller brush won't turn. I had opened the bottom to clean hair off the roller. the belts are not broken. When I closed it and turned it on, now the roller brush won't turn. I can push and turn it by hand, but not easily. Then I noticed the brush on/off switch is turned off, but when I step on it, it won't turn on. I was thinking I let something get out of place when I opened the bottom, but can't see what.
... Hoover Tempo Widepath Upright Vacuum - Blue
I am trying to replace my vacuum belt and can not get the roller brush to fit back into the slot after I put the belt back onto one end of the roller brush. Am I reassembling the belt and roller brush the right way?
If its a hoover or bissell, one side of the brushroll is slotted and slides. if its a eureka the hexagon end caps must be properly aligned, they go in at an angle. if its none of these provide me with the make and model # and i will give you a detail ... Vacuums
The belt wont turn...i cant get in to the inside to check to see if the belt isnt on the roller...how do i get up in there..i took the bottom plate off and you still cant get inside... thx Peggy
The following site has some great info on your machine:\015\012\015\012www.dysonmedic.com ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Kenmore Canister Vac, Progressive, 25512 255513 model. Brush won't turn. One end of the brush roller, end closest to belt, is off center which is keeping it from turning freely. The end cap is like a square. Other ends turns fine. Do these end caps come off? If so how? Can't get it to budge. This is exactly what is keep brush roller from turning.
Take a flat head screw driver and pry the end cap off. It will come off. You might have some string or hair around it causing it to not turn. ... Kenmore 25512/ 25513 Progressive Canister Vacuum
I cant get the belt and roller back on
... Riccar 8955 Upright Vacuum
I have a model # 880 Royal upright that the brush roller ends are bad. Can I get replacements for these? They have the 1/2 in. square ends. What about replacement for the whole roller assembly. The brushes are fairly well worn. Thanks, Arthur Summers
The below site sells the rollers for some models. I'm not sure about yours. The second one, part number R-673273, may fit. Check your brush for a part number. \015\012\015\012 ... Royal Vacuums
How do i take the old belt off of my dyson dc 14? cant seem to figure out how to get the roller separated from the machine because i cant get the old belt off.
Go to: Dyson web site or \015\012\015\012 http://www.repairclinic.com/0100_24.asp\015\012\015\012There should be 4 to six screws holding the ... Vacuums
I have an Electrolux EL 6988 type E Oxygan Bagged Canister vacuum brush roller in not working. I took off the stuff that was stopping to rooler from working and now I can't get the roller to move.
... Electrolux EL7024A Oxygen3 Bagged Canister Vacuum
I have a Kirby G series diamond edition. There seems to be no suction when I turn on the vaccum. The bag inflates, but the roller does not turn. It has a new belt and the roller brush is clean. Any suggestion on what I might do to increase the suction and get the roller bar moving?
THE IMPELLER LOOKS SHOT.. 25 QUID FOR NEW ONE,,LIFT THE LID AND TURN THE ROUND PIN AND CHECK FOR RIDGES ROUND THE WHITE IMPELLER,,IF NONE THERE THATS IT,, HAPPEND TO ME TEN MINS TO FIX GEORGE ... Kirby Ultimate G Bagged Upright Vacuum
DC 17 animal, axle roller that acts as a belt tensioner is shot, including the plastic mount that it sets in, (poor design) that wore down when the roller froze up. Where can I get just this part without having to buy the whole brush head assembly? Do they have one that is metal? Not the roller the mount for it>
I've had this stupid problem and my $500 dollar vacume has been broke for months so today after I spent hours on hold at dyson and talking to sears and everybody else under the sun and they say part doesn't exist pretty much, so finally I talk to a d ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
I have an old upright hoover vacuum. I need to change the belt but can't figure out how to get to it. The bottom plate over the roller brush comes off but I can't get anything else off to get to the other end of the belt.
Model no. req ... Hoover Vacuums
I cant get the roller back in place
On the ends of the roller turn the ends and you will see some teeth ,the teeth are supposed to be aiming down.if its because of the belt,slip the belt over the roller then put the belt on the motor shaft first and pull the roller towards the front a ... Oreck XLS700A Upright Vacuum
The brush is not moving on the vaccume. I'm pretty sure that the belt is busted. I cannot see how to get the shroud off, so that I can get to the roller and belt. It all looks and feels like one piece, even when I start removing screws. It is a bag-less vac. The model number is - v1310rs. Thank you.
I know on my Eureka I had to remove a couple of screws on the bottom and then get a flat blade screwdriver and wedge it on each side of the base kinda next where the end of the roller would be and it snaps up and off. Really weird I thought but that' ... Euro-Pro Shark Professional Upright Vacuum with Bonus StickVac Red Bagless Vacuum
Generation 4 Apparently, my belt came off while vacumming. I had a lot of hari entwind on the roller, so cleaned off the hair.... but now I can't seem to get the belt to stay "in place". Is it supposed to move around on the brush? or be held in place? It seems to me when I try to get the hook to grab ahold of the belt, it is going tohe wrong way to grab it. Please HELP!
First off get a new belt, I am sure this one has stretched. Then put the belt around the brush roll, put it in the center, put the bottom plate back on. Then turn the big knob on the front and turn it until it locks, you will know if it grabbed the ... Vacuums
Need to open rotating brush part of vacumm as motor functioning but roller not turning...perhaps belt broken put need to get into ..inside brush box ...Need help need instruction with diagrams Thanks for help Robert
... Panasonic MC-V9638 Bagged Canister Vacuum
I have a windsor vsp 14, it is making a bad grinding noise, when I take the top blue piece off it stops, the brush works fine and when I put the top back on it grinds really loud and gets hot. it still vacuums and the belt and brush are working fine, can't figure it out. and when the lid is on I cant see what its grinding on. It only makes a grinding noise when you pull handle back and engade to vacuum flor and stops when you put it upright.
... Windsor VS14 Versamatic Bagged Upright Vacuum
I took off the brush roller to clean it and now I can't get the roller to work unless the machine is standing upright. The side that's not connected to the belt keeps falling out.
The solution for your situation is as follows: You need to put the retraining clips on over the arms to properly put them in place You most likely put the retaining clips on too early. ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
I can't get the latch that connects to the brush head to engage. Thus the vacumn is extremely hard to push. It has suction, extreme suction. Rollers appear to be dragging. I've tried to remove and reinstall the head several times but cannot seem to get the latch to engage. Please advise.
It sounds like something has come out of it's socket. If the brushroll won't turn rapidly, your clutch is worn out ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Roller brush I took the roller off to clean it and now I can't get it back on without the left side just falling loosely to the floor.
Hi,\015\012\015\012you might need to order new floating roller bar holders, they were red on my bissell, they are held in place with two phillips screws on each end, I ended up using large washers to hold those on when my Bissell began m ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum
Manual issues Have reciently purchased a kirby from ebay (gotta love ebay) but has no manual. I believe the model is a heritage (cant see a II though) Do they all have roughly the same manuals??? I have all the attactments - spray painter, hair trimmer, turbo brush etc but really want to get the most from the machine. Where do I get manuals for machines that are 20yo???!!!
Many years ago I was a service engineer for these machines in England they were actually made by a company called Scott &Fetzer in the USA and Branded KIRBY or CIMEX.\015\012\015\012See if Scott &Fetzer are still around and ask th ... Kirby Heritage II Vacuum
I am trying to replace the cable and actuator on a Hoover windtunnel self propelled vacuum. but I cant get the top or hood off the get to them, I have removed all the screws I can see, roller, belts..what am I missing?? thanks so much for any help
Hi there SmartAlec from NelsonVacuums.com.au here. You will need to remove the knobs for carpet/hard floor selection and the carpet height to remove the cover they act as k ... Vacuums
Roller brush does not rotate if there is a belt I can't open that part of the vacuum to look. Vacuum is new but I vacuumed a string that caused the brush to stall for a moment. I could smell like when a belt gets hot or burns it's a surfacemax 300.
You need to replace the belt. Replacement Vacuum Belts ... Vacuums
I have the Dyson Ball DC24. I can't get the roller brush to come on...what do I do? I have pushed the red button on the side of the roller but it still does not engage...
Hi its Darran at Dyson.The brush bar re-set switch would normally resolve this, however as you have tried that, please get in touch with our Helpline on 0800 298 0298 (UK) or 1866MYDYSON (US) so that we can help resolve this issue for you ... Dyson Ball DC24 Bagless Upright Vacuum