Having problems with your Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum ?

Repplacing power cord on Hoover Wind tunnel (not self propelled)

\015 How do I dis-assemble to replace the power cord on the Hoover Wind Tunnel (not sel propelled)\015\012\015\012Thank You\015\012\015\012Dick Miller\015

Answers :

Hi
This is HARD and you NEED electrical knowledge and IF NOT UP TO IT YOU COULD CAUSE PROBLEMS TO YOUR SELF AND OTHERS.
You do not say what the problem is with the cord.If is it damaged then it needs to be replaced with a new one.and then above applies.
Take Care as to what you do.
SAFETY FIRST---ALWAYS
Hope this helps
Jay
Repair Help & Product Troubleshooting for Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Repplacing power cord on Hoover Wind tunnel (not self propelled)


I am thinking that the cord goes in on the back, just below the handle. Remove the handle, then from the front, remove the tool holder(#8), then you can get to where the cord comes in and hooks up.\015\012\015\012 ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Repplacing power cord on Hoover Wind tunnel (not self propelled)


HiThis is HARD and you NEED electrical knowledge and IF NOT UP TO IT YOU COULD CAUSE PROBLEMS TO YOUR SELF AND OTHERS.You do not say what the problem is with the cord.If is it damaged then it needs to be replaced with a new one.and then ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

On my Hoover 6660-900 bagless upright self propelled wind tunnel vacuum when I replaced the cable which works the power drive, there is a spring next to the control arm which I cannot quite figure ou


... Vacuums

Hoover Self Propelled Wind Tunnel Turbo Powered 7600 The thin belt too loose


If this is a "V" belt, make sure the small roller that tightens the belt is ok and not jammed up. It may have to be replaced. Also if the flat belt is stretched at all, it won't work either. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover self-propelled wind tunnel doesn't self propel going backwards.


Your self propel cable sounds like you need to have an adjustment. reccomend a service shop repair. ... Hoover Vacuums

I have 2 Hoover Wind Tunnel-self propelled bagged vacuums-U6433-900 model.The roller bar does not agitate, the self propelled feature does not work and, in general, the vacuum is not performing well. I have replaced the roller bar, the v belt and the wide belt. The filters have been replaced and it has a new bag. I have had both of these since 2004 and they were fairly expensive $200 each) but if the repairs are prohibitive, I might as well get new vacuums. Suggestions? I just spent $100 for bel


The Hoover WindTunnel self propelled is a machine that we see in our retail stores (Vacuums Unlimited) constantly. The benefit of having a supposed "self-propelled" machine wears of quickly after the numerous time you will need to take this machine ... Hoover Vacuums

I have a Hoover Wind-tunnel Vaccum (Model U5433-900) that needs a new power cord. I am looking for step by step directions for replacing the power cord


... Hoover Vacuums

My self-propelled Hoover wind tunnel vac. cleaner is hard to push


... Hoover Vacuums

Hoover wind tunnel retractable power cord


... Vacuums

Replace power cord Hoover U5757-900 - Hoover Company Wind Tunnel U53019 Upright Vacuum


... Hoover Company Wind Tunnel U53019 Upright Vacuum

Hoover Wind tunnel self propel not propelling - how do I know if it is the belt or the idler arm?


... Hoover U6485-900 Windtunnel Bagged Upright

Hoover Wind Tunnel U6458-900 Self Propel doesn't work - via other expert advice here for other models of Hoover - I'm thinking it is the actuator that needs to be replaced as I can see the cable does not connect to anything on the bottom. My problem is - I can't get the cover off. Been trying for a couple of hours. I removed every screw I can seem to find but something is hold it down. I also am wondering if/when I do eventually get the cover off, would I need to replace the cable when I replac


On some models there are hook/springs that hold the cover of the base snug. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

HOW DO I REPLACE THE DRIVE BELT ON A HOOVER WIND TUNNEL SELF PROPELLED


Take the brush belt and slip it over the pull into the groove. Then take the flat belt and hook onto the motor shaft and then pull belt over pull and push it around the entire pulley. It can be difficult but after the first time it is easy. You ha ... Hoover Company Wind Tunnel U53019 Upright Vacuum

Self Propel doesn't work on Hoover Wind Tunnel


Your self propel wire could be broken. Lean the vacuum back like you were using it. If you stand in front of the vacuum look down and to your left. When you move the selp propel button you should see a wire move. If not then it's broken. ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Hoover wind tunnel u5755-900. smoke, smell. self-propel


Can you verify the model number? However, based on your posted description, it sounds like the flat belt is either broken or fell off. to access the belts turn it over and remove the bottom plate (4 screws). the Flat belt will connect to the motor sh ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Hoover wind tunnel won't self propel


There are really two reasons why the self-propelled wouldn't work. It could either be the belts on the vacuum cleaner are stretched or broken. The belts on this model control both the self-propelled transmission, as well as the brush roller. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I own a self-propelled Hoover Wind Tunnel vacuum cleaner (Model U6425-920). I do now have an owner's manual and was wondering how to clean the Hepa filter on this model (*this model uses a vacuum cleaner bag also).


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=794479\015\012Generic problem for all Vacuums\015\012I own a self-propelled Hoover\015\012Posted by goh ... Vacuums

Is there any way to repair or replace the belt GUIDE on the inside of the belt compartment of a '97 Hoover Wind Tunnel (not self-propelled)? It became twisted when a belt broke and now the belt rubs against it and sounds really weird, and I'm sure new belts will continue to break.. This guide is a long piece of molded material (part of the compartent wall) to keep the belt from coming off the pulley. It also had a sort of metal clip on it. It was loose and I took it off because of the way the pa


Honestly you should take it to a vac.shop they can fix any vac. ... Windsor SR12 Sensor Bagged Upright Vacuum

How do you change the belt on a hoover wind tunnel vacumn/ not self propelled?


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a Hoover Wind Tunnel Self propelled 12amp. There seems to be very little suction. I have cleaned the hoses and filters but still not much suction. any ideas? thanks.


I have the same problem , and Like the the person who asked the Question ,, there is no Blockage ,, Im thinking maybe these filters have a very short life span ,, and even cleaning theses filters with a brush, etc , may not be enough, and could have ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Hoover wind tunnel upright self propelled. U6473-900. Brush does not work. Heard it was a 'brush controller' problem and can be fixed. Please tell me how.


Most likely the flat belt has stretched enough so as to not turn the pulley that in turn turns the brush roll using a V belt. Also there is a small idler wheel, if hook up, then it won't engage the V belt. ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Hoover Self Propelled wind tunnel vacuum U6433-900


I need to replace the actuator pivot arm on my Hoover Wind Tunnel to fix the self propel feature. I can see where it needs to go but I can not seem to get the cover off the vacuum so I can get to it. How do I do this? ... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

Why wont the self propelled brush on the hoover wind tunnel work. large belt is ok. the small belt looks 0k.


No don't do that,have a little patience.check where the self propelled assembly is and see if anything got in there,something might be loose and the teeth are meeting each other.thats a good vavuum.i have 2 but their not self propelled.try taking the ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Folks, My wife and I own a three-year-old Hoover U6434-900 self-propelled "Wind Tunnel" upright vacuum cleaner. The problem is that, even on the highest setting (front-end as high as possible), it gets bogged-down in even shallow pile carpet to the point that the brush stops. I've cleaned the machine thoroughly, pulling hair, thread, dental floss and such from the brush (and everywhere else), including unscrewing the brush end caps and pulling out the cat hair mats which formed in there.


Check to see if the V belt sits too deep in the brushroll groove, if it sits too deep you will need to replace the brushroll. the top of the belt should be about flush with the brushroll. also you have to take the screws out of the self propelled uni ... Vacuums

Hoover Wind Tunnel Upright Self-Propelled


Thanks to reddevil6. Sure enough it was the belt. What I did was take off the belt and flipped it over, worked like a charm. Since it was stretched on one side the other side was still ok. Still need a new, but s aved me a trip to the store! ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0853 seconds