Having problems with your Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum ?

Self propelled doesn't reverse

\015 Can you help me with the adjustment of the cable that moves back and forth for forward and reverse? I think the problem is the adjustment. The cable is connected but it feels like it doesn't go into reverse.\015

Answers :

Repair Help & Product Troubleshooting for Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover Upright Bagless WindTunnel does not self propel (U6625-900). Belts are new, Brush turns strongly. Wheels propel forward very weakly and do not reverse when the handle is pulled backward. Is there a mechanical link from the self propel switch to the "transmission" ? Are there any gears that could be worn or not engaging properly?


... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Hoover self-propelled u6630-900 reverse not working


THe forward/reverse lever (made of plastic) possibly is broken. New part is about $10.00 ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

G-4 Kirby self propel unit works in reverse but not foward


Jon,\015\012Here is a helpful link to use to adjust the tranny. About a 7 on the difficulty level.\015\012\015\012http://www.greatva ... Kirby Ultimate G Bagged Upright Vacuum

G-5 Kirby self-propel works intermitently. The handle must be jiggled until it engages forward. The same for reverse. Once underway it will continue indefinitely until the need to change direction. Jiggle go forward,jiggle go in reverse. It seems as though it helps to push the handle at an angle to the left depressing the switch on the left side at the base of the vacuum head.


Sounds like a loose wire, the wire is connected to the handle, you may be able to fix this yourself but be careful you can void the warranty by doing it your self. (most people make the problem worse) remember your kirby has a lifetime warranty (limi ... Kirby Ultimate G Bagged Upright Vacuum

Self propel will go foward, but will not reverse. Seems like handle is all the way extended.


My machine wont go forward or reverse. The handle wont move up or down but just a little which slightly moves the actuator piece. The switch wont disengage to the off position either. I have tightened the cable and loosened it also. No change. What a ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hoover vac 6432-900 reverse cable broke this model # is correct about 12 years old wind tunnel bagged self propelled


The quick and easy here is to just splice the cable and tape it. If you just cut the insulation back to get to the wire and get a couple 'barrel connector' at the hardware store. These are crimp style connectors and you need a small crimper to put th ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover 6485-900 self propelled will not roll. Self propel switch seems flimsy and I can't tell if it's working. New vac used about five times. I can see a wire moving down near the rollers when I engage the self propel but the wheels don't turn. Thanks for any assistance you can provide.


... Vacuums

On my hover U6616-900 the self propell work fine on the med setting on med height carpet, but when I go to low height carpet and height set on med the self propell does not pull the vacuum and it is hard to push. Also if I raise the height to the highest setting the self propell works correctly and appears to clen. Any ideas? S/N 090400184555, think this vacuum is maybe 5 years old and my wife uses it lots. Should I think of maybe a complete overhaul or a replacement at this time?


This is a typical problem you are describing. I would recommend you change the belts, this will resolve the "hard to push" and most likely resove your issues. based on the s/n given you maching was made on sept 2004. ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

Just put handle on windtunnel u6401-9rm and the self propelled switch will not flip into self propel mode. is there an adjustment on the self propel part?


When installing the handle on this machine, you must be sure the on/off switch and the self propel button are both in the OFF position. The actual switch inside must also be OFF, and the metal fitting on the end of the power drive cable should be bet ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Kirby G5 self propel problem


There is an adjustment for the transmission and it is wrong. It could also be worn. The Kirby has an amazing warranty. See if you can get it serviced for free. ... Kirby G5 Bagged Upright Vacuum

I have a Dirt Devil Vision self-propelled vacuum cleaner. Recently, the self-propelled feature is stuck in the backward mode, so it only goes backwards! I can get it to go forward if I push really hard (i guess it is good for a workout!). I try to turn off the propel feature completely, but it will not turn off. please help!


Hi, the problem you are having is going to be with the switch that controls the forwards and backwards settings so with this stuck in backwards their is no way you can get this turned off, the other problem is your not going to be able to replace thi ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

Have hoover self propelled vac uh60010 new in box but out of warranty.


This video will show you the fix ... Tti Hoover UH60010 WindTunnel Self-Propelled Bagless Upright Vacuum

Self propelled clicking noise


Check the cable that connects from the handle to the power drive. you might have broken a fastener between the two. ... Vacuums

I have a Hoover power max self propelled vacuum. The belt that goes to the self propelled part keeps slipping off. I've had the belt replaced, but the problem persists. What can be wrong? I've taken it to a Sew N Vac repair, but all he did was replace the belt again. And it still has the same problem.


I can guess of one problembelt gets removed when motor is running right?am assuming that belt is fit tightly and fits correctly when motor is in restif so then ur motor is not running at a proper speed which can be a pos ... Vacuums

Self-propelled Broken? Vacuum very hard to push. Self -propelled doesn't seem too be working. What can I do?


I have the same problem, found out there is a cable that is broken, I'm trying to figure out how to fix it. ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

How to disassemble self propelled vacuum to repair level that turns on self propelled mechanism


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hoover U6637-960 the self propel is not not working. When lowering the handle it acts like it would like to work but the roller will not turn. appears to be something to do with the self propel part of the handle . took the screws aout but can not get it apart. Is there another belt of something in there?


This vac has 2 belts. If both self propel and roller not spinning then most likely it is the wide flat belt broken or off. 4 screws on the bottom should gain you access to the belt area. another issue for this model series is a worn pulley on the rol ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

My oreck self propelled belt came off so I put it back on but it doesn't self propel and I smell burning.


... Oreck XL Ultra Bagged Upright Vacuum

Self-propelled Hoover windtunnel (with bags) will not self-propel. Belts are all in order, but I am quite sure it has to do with the cable. How would I fix this and how does the end of the cable with a nut, connect?


This might help - go to following website and look for "troubleshooting" \015\012http://www.fixya.com/support/p40544-hoo ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have 2 Hoover Wind Tunnel-self propelled bagged vacuums-U6433-900 model.The roller bar does not agitate, the self propelled feature does not work and, in general, the vacuum is not performing well. I have replaced the roller bar, the v belt and the wide belt. The filters have been replaced and it has a new bag. I have had both of these since 2004 and they were fairly expensive $200 each) but if the repairs are prohibitive, I might as well get new vacuums. Suggestions? I just spent $100 for bel


The Hoover WindTunnel self propelled is a machine that we see in our retail stores (Vacuums Unlimited) constantly. The benefit of having a supposed "self-propelled" machine wears of quickly after the numerous time you will need to take this machine ... Hoover Vacuums

Hoover self-propelled wind tunnel doesn't self propel going backwards.


Your self propel cable sounds like you need to have an adjustment. reccomend a service shop repair. ... Hoover Vacuums

Just replaced the belts on my Hoover Windtunnel II self-propelled vacuum. The brushes are now turning ok, but the self propelled feature is not working. Squeals when when you lock it in the upright position.


Check the plastic part, which the the self propelled cable is attached to. (release the handle, tilt it back. You should be able to see the cable attached by a screw to a black plastic arm.) It is either broken or the cable is lose. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hoover self-propelled self-propel not working. belts ok.


No suction on Windtunnel 6630-900. All belts work, brush turns, it just won't pick up anything. ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Self Propel The vacuum will not work in a self propelled mode.


Me again with more info. This happened to me and I solved it as described previously. More info here:There's a microswitch located where the hose attaches to the bottom section of the vacuum. If the hose is not completely inserted, th ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0203 seconds