Having problems with your Hoover U6476-900 WindTunnel Vacuum ?

Replacing belt but where is the motor shaft

\015 Hi! I took my vacuum apart to find out why it wasn't sucking up dirt (otherwise known as vacuuming ha ha). I found the flat belt wasn't attached on both ends. One end was attached to the brush roller, but the other wasn't attached at all. So, I knew what the problem was and went to the manual to find out how to attach it. It said to attach the other end to the motor shaft, but I can't find it anywhere! That sounds very silly I know but the manual's picture is pretty poor and looking around my vacuum I can't seem to find anything like that to attach it to! I'm desperate because I'm sick so I'm stuck at home but I'm leaving early Friday morning to go out of town and need the vacuum to work before I go! Any pictures to show me or a video or something would be so appreciated!\015

Answers :

The shaft of the motor might be through the hosing on the under side of the vac where the brush is. give me the model #
Repair Help & Product Troubleshooting for Hoover U6476-900 WindTunnel Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the


Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

Replacing belt but where is the motor shaft


The shaft of the motor might be through the hosing on the under side of the vac where the brush is. give me the model # ... Hoover U6476-900 WindTunnel Vacuum

How do you replace belt on dirt devil self propelled vision vacuum - can't find the motor shaft


You can download the manual from here > http://dirtdevil.com/search/?q=self+prepeld ... Vacuums

I want to replace belt from motor to transfer shaft


Hi.\015\012\015\012I presume your talking about the 2 clutch belts.\015\012Difficult to explain so try this site it has manuals to show you how.\015\012http://dysonmanuals.inc.io/ ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Putting the belt over the motor shaft


The belt may be overloaded because something it is driving is jammed or partially siezed . It could be a bad bearing or string wrapped around the beater brush etc. Check that everything moves really freely before going through this again. Take it all ... Hoover Elite U5061-900 Bagged Upright Vacuum

I don't know how to replace the belt on my hoover upright. The manual diagram does not display how to get to the motor shaft. (U4617-930)


... Hoover U4707900 Upright Vacuum

I have an old Hoover vacuum model # U5035-930. The belt broke and I tried replacing the belt myself. I couldn't stretch the belt to attach it to the motor pully. It was belt # 38525-027 M6. Which I got from the previous owner. I took it to a vacuum repair place and he replaced it with belt # 38528-027 J4. I cannot find this belt anywhere.


... Vacuums

The brushes will not rotate on my hoover vacuum. the belts are in good shape, the motor is turning the vacuum motor, but the belt on the brushes seems loose. I ordered a replacement belt but still nothing. Their is a small "idler" but their dosent seem to be enough tension on the belt. Any ideas?


Did you order the correct size of belt? These are the belts you should have:Hoover Windtunnel Belts ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a Kirby Dual Sanitronic '50' Vacuum Cleaner I bought in 1966. The motor does not start when I attach the belt lifter of the rug nozzle. When I remove the rug nozzle and detach the belt from the motor fan shaft the motor starts when I depress the nozzle switch and the power switch . Seems like the brushes in the motor are worn out. I do not have a manual for this unit. Can you assist me as to what newer unit is this compatible to and the problem I'm having at present??


... Kirby Vacuums

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?


Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Trying to replace belt on hoover convertible bagless upright u8188900. belt replace # 38528-049. i have opened vacuum and put belt back on, but it will not get tight enough around the motor gear and the brush spool to be able to activate. am i missing something? mike


... Hoover Vacuums

The belt on my used Eureka Boss 5857 upright slips off the end of the motor shaft every time the vacuum is used. When I turn the brush roll slowly by hand, the belt walks toward the end of the shaft. It looks like there was a plastic projection from the base that snapped off, and maybe that plastic piece used to block the belt from falling off. Do I need to try to reconstruct that plastic piece, or is something else wrong?


... Eureka 5856BVZ Boss Bagless Upright Cyclonic Vacuum

Schematics I went to replace the belt, and when I put it back on I noticed the silver pulley that the brush belt goes on has came unattached from the red piece by the motor belt. It is one peice. I can order a new pump, but I need the schematics so I can replace the pump. http://www.vacuums24x7.com/bistclpa.html How can I enlarge this so i can read it?


Well you can right click the picture and save it to your desktop, I did it, but it was alittle blurry. But if this doesn't work for you, post me your email addy and I can send you a better picture. But take the top off, there are 6 screws, 3 on ea ... Bissell 8910 ProHeat Clear View Upright Vacuum

I have recently replaced the belt and filters. The belt is in the correct position and the rotating brush moves freely. The motor is very loud. It still vacumns but I'm afraid the motor will burn up.


Does it sound different than it did before you made the repairs to it or does it sound the same. Just so you know some of the upright vacuums on the market today sound like a jet airplane landing in your living room.Ca ... Bissell 6594 PowerForce Bagless Upright Vacuum

Is there a motor pulley for the brush drive belt on a bissell 3750 upright, or does the belt just ride on the motor shaft?


Just on the shaft make sure there is no hair or threads on shaft and where belt goes on brushes ... Bissell 3750 Lift Off Bagless Upright Vacuum

Belt replacement appears to have 2 belts, 1 is on and 1 is missing, the belt that is driven by the motor is missing, how do I remove the clutch housing where the belt goes?


Hi.\015\012\015\012You are correct there are 2 belts.\015\012They can be tricky to replace most shops will state they cant be replaced & you require new clutch.\015\012So try this site ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The belt on my Kirby G3 wore out, and I bought replacement belts from two different sources--one an official Kirby supplier and one a store brand. Neither belt is long enough to catch the belt lifter when it is rotated and to reach the drive shaft.


Kirby has only had 1 belt from day one. sometimes you do need to push the belt up to catch the belt lifter ... Kirby Generation 3 Bagged Upright Vacuum

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc


... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the


... Dirt Devil M088905 Vision Bagless Upright Vacuum

I have a Necchi LYdia 3 machine type 544 The motor was overheating and I removed the bottom cover and examined the motor .It looked fine and ran well. It worked OK for a time and then got hot.I was able to partially remove the motor for inspection.I found that the cooling impeller was not secured to the shaft,I tightened the set screws and reinstalled the motor. In process of getting the drive belt back on I turned the wheel that extends out of the case to index the screw that attaches the bobb


Good day!Please try to re align the motor position.You have to do is repeat the procedure that you take to remove the motor and double check the alignment because all motor in misalignment is very hard to turn.And ... Vacuums

My Sharp EC-l2TWT4 throws belts and I noticed the motor shaft was not running straight. My wife took it to my local dealer in Brainerd,Mn and they said it was fine.So I took it apart and found the plastic motor housing had melted at some point letting the motor twist out of alignment. Other than this, everything works great.Can I order this plastic housing piece somewhere?


I checked the schematics for that model and the motor housing for that model is no longer available. Your best bet is to either attempt to find a used part or trade it in and get a new unit. Sharp no longer makes any vacuums or parts which makes thes ... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum

Replacing a belt on the Riccar 8850...I see how the brush assembly will work with the new belt. But I don't see how a new belt will turn on the small rod extending from the motor. Is there a pully missing?


There is not a pulley missing, when the belt is tight the shaft will turn the belt but when the belt loses elasticity it will slip on the shaft when being used on the carpet. Replace the n\012belt at least once or twice per year. ... Riccar 8850 Vacuum

Replacement parts... I've got a 3594 Bissell and the belt has come completely off. In the process of breaking, it bent the metal guide inside the motor housing and melted the plastic that holds the guide and keeps the belt inline with the roller. I've got it running again by using a screw I filed all the threads off of, but it only works for 10 minutes at a time before breaking another belt. This process is getting expensive, as it usually takes 30 minutes to completely vacuum the house. Is ther


Most likely it is the top cover that needs to be replaced, part #2031238 and is around $30. It would have that guide on it. ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn


Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum

Motor is sparking and smells like burning rubber. When it first happened I thought the vacuum had something jamming the beater bar. That was the smell it had, like when the belt gets burned. But when we turned it over, it wasn't jamming. Took off the base plate and turned it on. The motor area is sparking and it makes a weird noise (I assume that is because the motor fails and restarts). I looked for loose wires, can't find any. I believe I need some sort of part replaced, maybe even a n


From sound and description most possible is motor is burnt up sparks usually mean metal on metal either bearing or bushings went on motor if u can jiggle the shaft thats bearing if u rotate the shaft by hand and feel and or hear rough grinding the br ... Oreck Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0577 seconds