Having problems with your Hoover U6476-900 WindTunnel Vacuum ?

Sluggish self propelled problem on windtunnel hoover. help?


Answers :

Repair Help & Product Troubleshooting for Hoover U6476-900 WindTunnel Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Sluggish self propelled problem on windtunnel hoover. help?


... Hoover U6476-900 WindTunnel Vacuum

Hoover Self-Propelled WindTunnel U6436-900 cable problem


The flat belt should be changed if it has been longer than 9-12 months. Next I would remove the upper handle to inspect the top section of the control cable, sometimes it fray's and has a sponge feel (no positive control) to self propel. To set this ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover Bagless Windtunnel - Self Propel feature not working


I have the same problem with ours. If you lift the vacuum by the handle it breaks the lever on the transmission. You can find a replacement cable and lever on line for about $16.00 it is somewhat involved to repair but can be done by someone with mec ... Hoover Vacuums

Ihave a Hoover Windtunnel self-propel model U6445-920. The belt from the drive motor to the big wheel will not run in the center of the wheel. The belt runs about 1/3 off the wheel. I have tried several new belts and still the same problem. What do I need to do to repair this problem.


The large wheel may be worn off center. If the belt stays on and is not thrown, you can run the vac. if there is wobble in the wheel causing a genuine belt to slide off replace the wheel mechanism. ... Vacuums

In trying to repair foot pedal on my Hoover Windtunnel self propelled bagged vacuum, I got carried away and took apart most of the unit and I am still not able to get to the release..... I need help fixing the release lever AND then advise as to how to put the sweeper back together....Help!


This video should help you ... Hoover Vacuums

Hoover windtunnel self-propelled vacuum is not suctioning, changed belts, new bag what is the problem and i have checked the hose.


Have you cleaned the filters? ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My hoover windtunnel is not picking anything up all of a sudden. Also the roller underneith is not spinning. I've replaced filters and the attachment part is working fine, just when it's in the upright position it won't pick anything up. It also doesn't seem to be self propelled anylonger either. It use to **** everything up, including the dog. Please help!


The belt that drives the brush roll has broken. That's why it doesn't pick up and why it doesn't pull itself forwards. Check the User Manual (download from Hoover website if necessary) for information on replacing the belt. Good luck! ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have a Hoover self propelled WindTunnel vacuum( Model U6425-920) that stops in the middle of cleaning. I have changed the flat belt and I'm still experiencing the problem. I usually have to wait an hour or so b/4 it would work again. Any advise?


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=632298\015\012Generic problem for all Vacuums\015\012I have a Hoover self\015\012Posted by thjunk2007 o ... Vacuums

I have a Hoover Windtunnel, Self Propelled, Bagged, Upright vacuum. It makes a continuous squeaking noise when I pull backwards. What is causing that? Thank you for your help.


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I am trying to replace the cable and actuator on a Hoover windtunnel self propelled vacuum. but I cant get the top or hood off the get to them, I have removed all the screws I can see, roller, belts..what am I missing?? thanks so much for any help


Hi there SmartAlec from NelsonVacuums.com.au here. You will need to remove the knobs for carpet/hard floor selection and the carpet height to remove the cover they act as k ... Vacuums

My self-propelled windtunnel bagless hoover does not pick up.


Remove the dirt cup.\015\012Remove the filter screwed in at the top of the dirt cup opening.\015\012Remove the hepa filters on the side of the machine.\015\012Clean all filters and re-install them. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Replacing Main Body on Hoover Windtunnel Self Propelled


... Hoover Vacuums

I have a Hoover power max self propelled vacuum. The belt that goes to the self propelled part keeps slipping off. I've had the belt replaced, but the problem persists. What can be wrong? I've taken it to a Sew N Vac repair, but all he did was replace the belt again. And it still has the same problem.


I can guess of one problembelt gets removed when motor is running right?am assuming that belt is fit tightly and fits correctly when motor is in restif so then ur motor is not running at a proper speed which can be a pos ... Vacuums

Hoover Upright Bagless WindTunnel does not self propel (U6625-900). Belts are new, Brush turns strongly. Wheels propel forward very weakly and do not reverse when the handle is pulled backward. Is there a mechanical link from the self propel switch to the "transmission" ? Are there any gears that could be worn or not engaging properly?


... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Just replaced the belts on my Hoover Windtunnel II self-propelled vacuum. The brushes are now turning ok, but the self propelled feature is not working. Squeals when when you lock it in the upright position.


Check the plastic part, which the the self propelled cable is attached to. (release the handle, tilt it back. You should be able to see the cable attached by a screw to a black plastic arm.) It is either broken or the cable is lose. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Self-propelled Hoover windtunnel (with bags) will not self-propel. Belts are all in order, but I am quite sure it has to do with the cable. How would I fix this and how does the end of the cable with a nut, connect?


This might help - go to following website and look for "troubleshooting" \015\012http://www.fixya.com/support/p40544-hoo ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

V-belt flapping on Hoover Self-Propelled WindTunnel Bagged Vacuum


... Hoover U6441-940 WindTunnel Bagged Upright Vacuum

Repplacing power cord on Hoover Wind tunnel (not self propelled)


I am thinking that the cord goes in on the back, just below the handle. Remove the handle, then from the front, remove the tool holder(#8), then you can get to where the cord comes in and hooks up.\015\012\015\012 ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Hoover windtunnel Self-propelled - brush roll stops


There is a idler wheel that will drive the V belt, sometimes they jam and you just have to reach in, push and make sure if comes in contact with the belt. Alot of times tho it is the other flat belt, 38528035 that will stretch and can cause you to h ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

I have hoover WindTunnel Self Propelled Vacuum


Greetings from GoVacuum,Here's a great video repair tutorial that we've put together to try and help you with the repair on your Hoover WindTunnel. I hope that this helps you with your repair. If you found this ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Self-propel not working on my Hoover Windtunnel


... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Hoover Self-Propelled WindTunnel, U6434-900 on/off switch doesn't


... Vacuums

Hoover WindTunnel Self Propelled Handle Release Lever broken


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover WindTunnel Self-Propelled V Belt


I had this same problem with the V belt on my Hoover Vaccuum.\012\012There are three (3) basic things that will cause the brush roll not to spin.\012\0121. When handle is upright, brush roll is OFF.\0122. When switch is set for HARD surfa ... Hoover U6441-940 WindTunnel Bagged Upright Vacuum

Hoover windtunnel self-propelled - will not turn on


You probably need the switch replaced. It's fairly simple to do youself, and it is a known problem with these vacuums.\015\012You can order the switch from hoover for about $10 ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0922 seconds