Having problems with your Hoover U6476-910 WindTunnel Upright Vacuum Cleaner Bagged Vacuum ?

Hoover U6476-910 - Very little suction from the bottom

\015 Very little suction from the bottom, not clogged (took apart and looked) -- sucks fine from the top attachment... filter looks ok, changed bag... suction is weak and not like it should be. Any feedback is appreciated.\015

Answers :

If you haven't already, remove the beater bar. This is accomplished by unplugging the vacuum and turning it beater bar up. Remove the clips or screws that hold the plate on the beater bar and set aside. The beater bar sits in sockets, so carefully remove the bar, noting the correct position of the sockets. This will make reassembly much easier. Slip the beater bar out of the drive belt. Now, inspect the suction cavity that the beater bar would discharge into. Usually, things clog up here as there is a flex hose that catches things, creating a pluggage.
\015\012Hope this helps, --W/D--
Repair Help & Product Troubleshooting for Hoover U6476-910 WindTunnel Upright Vacuum Cleaner Bagged Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover U6476-910 - Very little suction from the bottom


If you haven't already, remove the beater bar. This is accomplished by unplugging the vacuum and turning it beater bar up. Remove the clips or screws that hold the plate on the beater bar and set aside. The beater bar sits in sockets, so carefully ... Hoover U6476-910 WindTunnel Upright Vacuum Cleaner Bagged Vacuum

My Dyson DC07 has recently been service and was making a clattering noise and very hard to push. We have taken it back and he has changed the clutch mechanism under the base which has solved the clattering, but it is still really hard to push because of the suction. It is even lifting the carpet in one room. Can you tell me what the possible reasons for this could be? One thought we had was that the little rubber wheels on the bottom cover could have worn so the hoover is closer to the floor


On the sole plate you should have 5 little wheels, these are prone to jamming after a while. You should make sure these are not jammed in anyway.\012\012You can release these with a screwdriver, but be careful not to prize too hard as you ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have any easy-flo built-in vacuum. I recently had the bearings on the motor, top and bottom replaced. I put the vacuum back together and it mow has low suction power. There is plenty of suction on the side of the canister where the rigid tubing meets the canister body but little suction at the wall plates. Any ideas? Roger


There is either a blockage or a pipe is open somewhere. You should check the system at the wall valve without the hose to determine if the pipes are blocked or if perhaps the hose is plugged. If one of the wall valves is damaged or open, this will af ... Vacuums

No suction how goes it.. my hoover windtunner v2 has no suction through the hose.. it does however have suction from the body, but once i put the canister in, it has very little through the hose.. no blockage in any of the parts.. whats up


Check again for obstructions in the hose. Also underneath where the debri goes when it is being sucked up. Also make sure all your hoses are connected as this could effect the suction. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have a Hoover Wind Tunnel Self propelled 12amp. There seems to be very little suction. I have cleaned the hoses and filters but still not much suction. any ideas? thanks.


I have the same problem , and Like the the person who asked the Question ,, there is no Blockage ,, Im thinking maybe these filters have a very short life span ,, and even cleaning theses filters with a brush, etc , may not be enough, and could have ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

I own a Hoover Steam Vac V2 deep cleaner with Auto Rinse feature. The Model Number is not available ex: was on the bottom of the machine and the sticker is completely worn off the machine. I am having a problem with the bottle you fill with detergent ex: this bottle is seperate from the main clean water tank. THE PROBLEM: The little plastic part that goes in the bottom of the bottle has an "O" ring ex: cone shaped with a spring.....it keeps falling out. Can you supply a part number for this


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=641300\015\012Generic problem for all Vacuums\015\012I own a Hoover Steam\015\012Posted by w_brennan on ... Vacuums

Have an lg Hoover and the red light on the handle keeps flashing and the blue light on the Hoover is also flashing and then it cuts out. Has little suction with the head on it but better when you take it off. How do I fix the problem?


... Vacuums

Very little suction with my Hoover U5288-900 - Hoover U5288-900 Upright Vacuum


... Hoover U5288-900 Upright Vacuum

Suction When putting down the salution, my hoover doesn't want to pick it all back up. Very little suction. Any tips to what I can do myself?


Take the recovery tank out, there is a filter on the handle part where the tank sits in, make sure it is clean. Check for any other filters to make sure they are all clean. ... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum

NO SUCTION HOOVER U8143-900 UPRIGHT HAS LITTLE SUCTION ALL BRUSHES ROTATE SO I'M SURE THE BELT IS OKAY. DO YOU ANY SUGGESTIONS????


I took mine apart, cleaned otherwise inaccessible pipes, and assembled\015\012it back (that went well, huh!). The clog was made of human hair and and\015\012other long fibers (carpet pieces, etc). ... Hoover U8143-900 Upright Vacuum

Little Green pro heat is leaking from bottom with very little suction. I just purchased it.


Try the following suggestions for the leaking issue:\015\012\015\012- Check to see if the black or white "duck bill" gasket is misassembled or missing from the collection tank; ensure the gasket will open where the flat flaps meet ... Bissell 1425 Little Green ProHeat Handheld Steam Vacuum

No suction the vaccum sounds like its working and it picks up a little but it does not suction like it did 2 days ago. It is a hoover windtunnel bagless. the model number is U6600-9RM.


Have u checked all of the filters. I know that when not all the filters r clean the machine will turn on but then it will sound louder and still have no suction. Most times there is a filter under dirt container thats sits above motor and if this ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Little suction on Bosch formula hygenix hoover


... Vacuums

Very little suction on my Hoover Windtunnel Bagless twin chamber vaccum hose while using the tool attachments


... Vacuums

Hoover steam vac has no suction, blowing air from middle of bottom


Assure the ring gasket is in place under the hood. A round rubber gasket must be in place on the round tube under the hood where the recovery tank sits to connect the vacuum from the motor to the round tube on the bottom of the tank. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover SteamVac Model F6056-900 SteamVac/SpinScrub. Indicator light and high pitch suction noise indicates that dirty water tank is full. However, water level indicator (yellow bobbing plastic thing) is at the bottom of the tank and there is no water in the tank. Have check all the hoses for clogs, none found. Checked water port from motor area to receptacle tank for clogs, none found. Fixed broken hose to upholstery wand with duck tape, (wire not broken, just cracked plastic hose). The onl


There are 2 filters, make sure they are clean, one is on the tank lid, the other is from the bottom, it is red, pull it out and clean it. If yours has a foam filter on the tank lid covering the yellow ball, make sure there is at least a 1/4 in. gap ... Hoover Vacuums

I need the recovery tank front panel for the Hoover Carpet Cleaner, i have the tank can i just order the little piece that goes in the front of that for the suction to the recovery tank


Unfortunately its only available as one unit the hood, and suction cover ... Vacuums

Bought clearance item Sunday just found out the brush bar was motorized it turms only when i move the vacum back and fourth it should turn on its own right ? I have very little suction from the bottom the hose works though


This appears to be a loose connection. The below post was answered by highntools a while ago. It probably is related to you problem. That is why moving it back and forth makes it go on.\015\012\015\012I have finally fixed my sister's d ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

I have a Hoover Windtunnel Model U573-960, the belt turns the bar still has alot of life on it. I have very little to no suction at the end of attachment hose. I replaced filters and looked for blockagaes with no luck.


... Hoover Vacuums

No suction from the bottom


Hello the hose on the bottom of the unit is clogged with debris, try taking a straighten hanger of some sort, and stick into the entry hole on the bottom of the vac, to remove debris sometime paper and other forgein objects get caught in the vacuum h ... Eureka Whirlwind Litespeed 5840 Bagless Upright Cyclonic Vacuum

Need A manual for U5025-900 Hoover Sprint vacuum want to check if the filters are correct. Was given the vacuum, seems like there is very little suction for the hose. Any help would be appreciated


Wasn't able to locate a manual, but you may be able to get the info you need from this page:\015\012\015\012U5025900 Parts ... Hoover U5025-900 Bagless Upright Vacuum

Hoover steam vac won't suction water. It will with the hand tool, but not the main part. I feel hot air blowing out of the bottom.


... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum

Hoover Elite Deluxe rewind... Air flow indicator stays activated, after filter has been cleaned. Brushes spin, but very little suction. Dirt is not spinning in cup


... Hoover Vacuums

Hoover steam vac has no suction blowing air from middle of bottom


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Dc11 dyson the brush head turns very slowly but when i take brush head cover of (the yellow part) and put my hand over the suction inlet part the brush head turns really fast. Have cleaned out collection chambers eg the hoover bag have washed the sponge with the little pictures of taps on it what now . thanks alan


I have taken the brush heads off and pulled all the hair out of the small gap between the chrome shaft and the plastic gear housing. Then a small amount of 3-in-1 oil into that gap to lube the internals and just a little through the air intake on th ... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0842 seconds