Having problems with your Hoover U6616-900 WindTunnel Bagless Upright Vacuum ?

Smoke coming from motor

\015 I need a schematic on replacing the motor\015

Answers :

Http://www.globalsources.com/manufacturers/Vacuum-Cleaner-Motor.html
\015\012
\015\012There is a ton of vacuum cleaner motors at this link.
\015\012Hope it helps.
Hi,

You can download the user manual from HERE
Since the service manual is not available on the net you will have to contact the Hoover people for it.Here is the contact no.

1-800-944-9200


Here is 1 tip which i can give you:
From the bottom, remove the screws separating the top and the bottom.\015\012Then at the bottom, remove the round water seal, take out those screws,\015\012( careful with the water seal, reglue it with contact cement when you\015\012put it back on). At the top of the motor, take out the screws around the\015\012motor and it should pull out.

Goodluck,
Please don't forget to rate the solution:
Repair Help & Product Troubleshooting for Hoover U6616-900 WindTunnel Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Vacuum plugged in but not on, smoke started coming from the motor


The motor winding burned out. Perhaps the motor was very hot when the vac was turned off after the last use and the insulation of the motor windings broke down when the air stopped moving thought the unit. Perhaps also the polarity of the receptacl ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I have a Z345 Electrolux cylinder vacuum cleaner, from the 1970s probably, but not used much. I have lost the guide. I forgot to change the bag before it was full. Smoke started to come out - smelling of burnt paper, not rubber. So switched off. It did not blow the fuse, and may be OK. I wish to inspect it. How do I open it up? Alos I have an air filter and a motor filter for it. I have often changed the air filter on the top. How do I get at the motor filter, if there is one? Than


Good day! OK you have to is replaced the bag and that's it.And don't forget to change the bag again to avoid that problem.Thank you ... Electrolux Guardian Bagged Canister Vacuum

The wheel is not turning, and the motor seems to have a problem because it is smoking. Smoke coming out of the bottom where it would normally touch the ground when sucking. Model: Nissan 82g7-1.


... Bissell 82G71 Upright Vacuum

Smoke coming from motor


Http://www.globalsources.com/manufacturers/Vacuum-Cleaner-Motor.html\015\012\015\012There is a ton of vacuum cleaner motors ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

Bunning smell. How do I determine if it's the motor or the mother board? As there is no smoke coming out of the vacuum.


Is it an electrical smell or a rubber type smell. If there is no smoke, it could be that the belt is slipping and causing a smell. If it is the motor, usually it would smoke, or at least quit running and making strange noises. ... Vacuums

I have a motor for the Bissell 3750 power head with a black and brown wire, which wire is connected to what?? The old motor just had 2 black wires. There is a blue wire coming from the vacuum and blue wire coming from the light that are together, and a blue wire coming from the light and a black wire that are together. What does the blue and brown wire coming from the motor connect too? Thanks


... Bissell 3750 Lift Off Bagless Upright Vacuum

Smoke coming out of my Kenmore Canister Vacuum Model 22550300C


Sounds like a motor err. Could be repaired by a professional but it never be as good as a new one. Also they you might not find anyone to repair it because the replacement motor might cost more than a new vacuum /considering it's age the motor will b ... Kenmore Vacuums

Electrical problem The light comes on but the motor will not come on when the on button is pressed. Is there a reset button? I thought it was because the bag was full but I just changed the bag and the motor still will not come on.


The light is separate from motor. No reset switch. Check for a fuse but i suspect it may be brushes are worn out and not making contact.Sometimes that starts as an intermittent.Hopefully one of the coils isn't open circuited. ... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum

Vax rapide smoke from motor


... Vacuums

I have FILTER QUEEN vac that a friend gave me because he unhooked the 5 wires coming from the motor and he didn't know where they when could I get photo of the wires coming from the motor and whe


I would go through the manufacturer for the diagram. ... Filter Queen Cheetah II Ash - MU305 Bagless Canister Vacuum

I have a Electrolux , EL6988 Canister Vacum, howeveer the brushes and motor will not run when turned on. I have take the plates and cleaned around the brushes, but it will not come one. The vacum comes on but the motorized bushes do not activate. Thanks I have lost my owners manual, and have looked for the reset button and can't find or know where it is located. Any suggestions.


I need the molded wire harness inside the plastic wand ( one of the prongs is broke off) What is the part # or where can I buy it? Model EL6988 ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Smoke and bad smell coming from the base


You need a nw belt but before you change the belt clean the burnt rubber off the motor shaft or your new belt won't last ... Dyson DC07 Bagless Upright Cyclonic Vacuum

We have a hoover porta vac. that at first it would sometimes come on and sometimes not. It did completely stop coming on, so I have changed the switch and the cord but with no luck. Could you offer any suggestions or is this a motor situation. To my knowledge the motor was not making any noise. Your help would be greatly appreciated. Thank You, Molly Maid of NW Fla.


If this has had heavy use, the carbons in the motor may be worn. ... Hoover CH30000 Bagged Canister Vacuum

We own a dirt devil model 088600, and are experiencing a problem with the belt wearing away a section between where the belt connects to the brushes and the motor. There is a lot of plastic/rubber residue coming out from the vacuum. We have tried new belts only to find the same problem occurs. I noticed that the source of the dust is coming from the section between the brushes and motor, where there appears to be a section that is misshapen and melted. I looked up the schematic online and can't


If you are certain that the belt is seated correctly and the beater bar is nested in its holder and the cover of the assembly has been properly installed and you still see a contact area between the belt and cover, you should either: return the vac ... Dirt Devil Vacuums

We have the water hooked up at the back of machine. there is a spout for the water to come in and fill the ice tray.but is does not. If we turn the water on it fills up the space under the ice basket. I keep getting red light and then the two smal llight one ice and one water come on. We can hear the motor trying to fill the ice try and then lights come on. Please help me this so I can use this product. It did not come with a manual.


The water inlet valve on the back of unit opens when the ice maker needs water. If the valve doesn't seal good because of sediment or wear it will continue to drip and when the water reaches the ice maker supply tube it will freeze blocking the fill ... Vacuums

I have a dyson animal dc17 vacuum and it totally died. Now I can't figure out which wires go where when I install my new motor. (motor #: 160906G) Do you happen to know where the various color wires go or a place I can see a diagram of the motor with wires attached? I should have taken a photo of it before tearing out the old motor. I don't know where to connect the three coming out from the upright portion of the machine and the red seems to go to a switch (?) and there is a black (connected t


... Vacuums

Motor problem I just picked up a screw. It appears to be stuck in motor. The sound of the motor changed to a whirring noise and it started to smoke. How can i access the motor?


First six pictures HERE will let you know how to remove shell to see the motor. I would not recommend starting it before you get the screw out (you will need to ... Kirby Generation 3 Bagged Upright Vacuum

Motor problem When i plug my steam vac in the motor sparks and smokes. It smells as if the motor is burning out. I've tried different outlets through out the house and get the same outcome, what can i do to solve this?


Nothing you can do im affraid its the motor armature so unless it can be stripped down then you will need to replace the motor i would get a price for the motor to decide if it is worth doin sorry. ... Vacuums

Smoke from Hoover Savvy U8185-900. Looks to be from the Motor assembly U8174-900. How to access motor in order to verify condition, have already removed all screws, but unabale to expoxe motor..


... Hoover U8185-900 Upright Vacuum

My Nilfisk GWD 300s had been working fine, however today i could smell something like burning smoke from the motor, when i opened up the motor i could see a carbon metal rod touching the motor shaft a


... Nilfisk Vacuums

Sewing machine Guru needed ;) Elna Grasshopper (new to me) circa 1950 The light works, but there was no hummm when knee pedal engaged. I have the motor out, and it is very stiff to turn. I'm at a total loss when it comes to motors and electricity. It doesn't smell burned, doesn't smell at all beyond normal machine smells. (Yes, I made detailed notes and diagrams as I took said motor out!) One other note. The long thing which my husband said might be a capacitor -- it looks like


I just purchased a fairly tidy Elna 'Grasshopper' sewing machine (1951) with the same leaking capacitor problem. I carefully removed the capacitor for examination. It is actually three capacitors in one - no chance of a direct modern replacement, but ... Vacuums

I have a VX3000C Broan vacuum and the motor sometimes runs lower and comes back to normal time and time. Plus, now it lamost stops before coming back to normal speed. Can someone explain to me what that might be or if it did happen to someone else? It doesn't stop, but runs at very low speed and come back. It is like if a connection is not made properly. But it does the same at my 3 connections and I did check the one on the vaccuum itselfs.


... Broan-NuTone VX475 Bagged Central System Vacuum

Motor When i turn my steam vac on the motor flashes sparks and smokes and it smells as if the motor is burning out. I have it plugged into a normal household socket, i've tried different sockets with the same outcome.


You have it right either the motor is going out or water got in there causing it to spark and smell.sorry.lease leave feedback...pete ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Clarke Instructions helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? t


... Vacuums

Wiring diagram took wires off motor and do not know which goes where.There are two main from plug in one whit one black then two of same coming from light in front.On the motor ther are more terminals than wires.On diagonal corners there are black dots.Can you please help this cost 800$ and do not want to burn the motor due to crossing pos and neg.Do you have a picture or know where I can find?


... Oreck XL21 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0398 seconds