Having problems with your Hoover U6616-900 WindTunnel Bagless Upright Vacuum ?

Self propel does not work and it is real hard to push this way. We checked the belts and they both ok. Not sure what else to look at, the on line manual does not show any information


Answers :

Hi there SmartAlec from NelsonVacuums.com.au here. Ok on this particular machine the belts strtch quite a bit and make the machine very hard to push even though the belts seem to be ok. I would recommend first making sure that the driving self propell is actually working at all. Tip the machine on its back all flat and turn it on. When you push handle up and down you should see a pair of wheels spinning one way then the other (corresponding to the way handle is pushed or pulled). As long as the wheels are moving then it is just that the wide flat belt just needs changing even though it is not broken. If the wheels are not turning at all even though belts are in place then you have a more sinister problem that will require a technition to check over.
\015\012hope this helps!
\015\012happy Vacuuming :)
Repair Help & Product Troubleshooting for Hoover U6616-900 WindTunnel Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Self propel does not work and it is real hard to push this way. We checked the belts and they both ok. Not sure what else to look at, the on line manual does not show any information


Hi there SmartAlec from NelsonVacuums.com.au here. Ok on this particular machine the belts strtch quite a bit and make the machine very hard to push even though the belts s ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

I have a Hoover Windtunnel Farrington upright model U6431-900 It has worked flawlessly until last week. The roller brush has stopped turning and I believe it is the belt that has broken but I am not sure how to remove the cover to inspect it and replace the belt if that is the problem. Please inform me how to perform the operation and what I should I look for? Is there a site with a diagram on how to replace said parts? Thanks for any and all helpful info that you can supply me with. Larry


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=783264\015\012Generic problem for all Vacuums\015\012I have a Hoover WindTunnel\015\012Posted by ... Vacuums

No I did not my hose on the dirt devil does not have much suction on it I took everything apart and found nothing wrong no clogs anywhere but when I add an attachment to the hose it loses all suction...I looked for a switch to change from regular vacuuming to attachment found nothing why is this??????? Need a manual where can I find some information and a download on line manual??????


Try this. There should be a little filter unerneath the tank. just clean that filter or replace it. (9 times 10) thats the problem.\015\012\015\012good luck. ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

My Bissell Quicksteamer Model 1960-R won't spray cleaning solution. I have cleaned it and taken apart the whole thing. I can't find any problems. The holes are not cloged where the water comes out as I disconnected it and blew through it to be sure. The lines show water trying to go through. It is as if it doesn't have enough power to pump the water out when I squeeze the trigger. I am thinking it is the pump thing but can't find a replacement part for it.


... Bissell 1960-3 QuickSteamer Plus Upright Vacuum

Make a very loud noise when I try to vaccuum the carpet. It sounds like it's something in the brush up front. Belts look good and obstructions are gone. Not sure what else to do.


\015\012Try to lower your wheels a bit which will raise your vacuum a little off the ground. When you vacuum a bare floor you want the vacuum as close to the floor as possible. When you vacuum a carpet if you don't r ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Roomba Red shows pulsing red charging light, turns green, measured battery voltage - only shows about 5.5 volts. Borrowed and used neighbor's charging unit - same thing happened. It seems that the charging system inside the Roomba Red is not functioning. WShat else can I try?


... iRobot Roomba Red 4100 Bagless Robotic Vacuum

Electrolux Epic 6500 SR Carpet Sweeper won't go on. Belt good brush moves, bulb looks good, reset red button I'm not sure, works, looks good. Vacuum starts has suction ,


This link is the manualhttp://www.totalvac.com/manuals/electrolux_manual_Epic6500.pdf ... Vacuums

No Suction I get great suction in the hose, but when I plug the hose back into the unit, there is no suction and the air flow indicator line goes completely red. I've changed the bag and filters. I took the small panel off the back and made sure there is no clog, and took the hose off to make sure there was no clog there. Still no suction. Please help.


I about to say that's always a clog of some sort that causes that ... Miele S7210 Bagged Upright Vacuum

On a bissell 9400 steam vac i am getting spray from the hand wand but not the floor spray. I checked all the solinoids and lines and switches. I blew throurgh the lines and got no clogs. can you tell me what else can be wrong


... Bissell Vacuums

Does the hoover runabout u427-930 have a filter? I replaced the belt and next to the light bulb was a square gray mat that looked like a filter covering a screen full of holes that looked like the motor was behind. I think it was a mat of cat hair so I took it off and threw it away; I just want to make sure that it wasn't a filter that I need to replace.


From doing a search on the internet and hoovers website it looks as if this unit does not have a filter. Such as a hepa that needs to be replaced or that is washable. So i think you are safe and dont need to worry about it. ... Hoover Elite U5061-900 Bagged Upright Vacuum

My vacuum is making a loud noise like I sucked up somehting I shouldn't have I have cleaned all the hair and made sure there was nothing else stuck in there but it continues to make that loud noise is there something else that will cause it to make this ugly noise, and how can I fix it


... Dyson DCO7 Upright Vacuum

I have Hoover whisper Cyclonic. I just opend beacuse it was showing Clogged. I removed all dirt etc from the belt and now roller are not moving round and the smell of burning is coming due to rubber not moving on the roller. I looked at the manual which tells me in cased on roller being Jamed if need to use the stich to reset. I looked all over could not find the switch. Can you guys help me please.


... Hoover Sh40080 Zen Whisper Bagless Multi-Cyclonic Canister Vacuum

I have no suction for vacumming the floor. the wand is totally still working and sucking it heart out. clear hosing doesnt looked cracked. dont know where else to look.


Hi, if the wand is doing its job very well, you have to have a blockage some where, either in the hose where it attaches to the bottom of the unit near the roller section. It may be hard to see, but this is what is causing the bottom from not picking ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a Bissell Powersteamer Pro Deluxe, Model 8804 shampooer. I got this bright idea to take the brush off as it was full of hair and debree. Upon putting it back on it appears I'm not getting the brush on properly. Does the belt go around the end with the grooves? Also do the grooves go on the right or left side? From my view point I am looking at the machine with it lying on it's back and I am sitting on the floor looking at the bottom of machine. Sure hope I haven't confused you too m


... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

CEL lit up on dash. Codes point to possible loose vacuum line or faulty gas cap. Replaced cap with no change. Looking for vacuum line diagram if possible. Thanks, Brian


\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012 ... Vacuums

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o


Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Taylor 5739 scale does not function as is supposed to. changed batteries and reset according to instructions. scale goes to 0.0 then to bar lines, then shows over max symbol, then back to 0.0, then off. Sometimes it goes to show 363 lbs (I weigh 200).


... Vacuums

Bissell Proheat 25A3/64D9 series - cleaned one rug - now the wheels won't turn and it looks like the belts are on ok. What else should I look for?


I had the same problem. I found that when I took the belt door off, the belt was fine. I turned it over and took the red retainer arm out and then removed the screw on the white brush holder, the toothed belt was fine also. Somehow the machine had ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Oreck Upright Hi Redev, I'm not sure what model I have (about 6 years old...upright, looks like the one in the picture). I changed the belt (which was torn) and then the next time I used it, it cut off on me. Now if won't turn on at all. (I turn the switch on and off and nothing happens as if it is not plugged in but it is!). I noticed at the top where the power cord enters the handle, it is all frayed. Could the electrical wires have detached? Anything you think I should check before taking it


The cord could be bad and will ahve to be replaced. It would have to have a problem inside the handle or down by the motor. ... Oreck XL2600 Vacuum

I have a Hoover SteamVac Spot/Deep Cleaner, model F5515. I've had it a little over 1 year. It will not extract dirty water from the floor. I've made sure the recovery tank is attached correctly and also that the stair tool is connected. Is there something else I can try??


... Vacuums

Burning smell There is a burning smell when I run my Kirby Ultimate G.  The smell seems to be coming from the belt.  I looked at the brushes and they are spinning so the belt is working.  the Post on the vacuum is getting very hot not sure if that is normal.  What is causing this?


Unlock the sweeper brushes and take them out. on each end is a cup bearing and should be free of debris.then check around and under the belt and likely there is debris wrapped around it.the post is getting hot as your pulling too much of ... Kirby Ultimate G Bagged Upright Vacuum

My eureka Hello im not sure what kinda of eureka it is a friend gave it to us...and I went to change the bag and vacuum and the spinner isnt going...and i dont think its the belt...help please! i looked on the back and it gave me a modle number its 4475


The belt may look ok, but am sure it is stretched and when this happens, the brush roll won't turn like it should. Did you check the brush roll ends to see if they turn freely, if not replace it. ... Vacuums

I have a Eureka Central Vac CV1601b. The motor does not stop unless the Unit is unplug from the electrical outlet. Any Idea?.I removed the control unit to check if there was disconnected wires or burnt wires. Everything look normal. The circuit board does not show area that overheated. There seem to be 2 relays. Likely one of the two went bad. What do you think.


If the unit is relay controlled, there is always the possibility that when the unit was turned on, the relay contacts welded themselves shut making the power button ineffective. \015\012\015\012If you're familiar with relay pinouts, with ... Vacuums

I work for an Atlanta, GA nonprofit. We had a Pfaff 474 steam press donated to us. Am looking for an instruction manual for it--no luck so far by doing on-line research. Can you help?


... Vacuums

Last time I used by Hoover it worked fine, took brushes out to clean them and now when I try to put them back in they won't snap into place and lock. Looks like all tabs on both sides of the brush piece are there and I spin the brushes for the center spindle to line up but it won't snap into place.


Just slightly turn the brush wheel, The tabs look square, but are just a little different in one direction ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0317 seconds