Having problems with your Hoover U6616-900 WindTunnel Bagless Upright Vacuum ?

How to replace power cord on Hoover WindTunnel upright vacuum

\015 The cord on my Hoover WindTunnel upright vacuum is damaged from having been run over while vacuuming. I purchased a replacement power cord, agitator brush, belt, and filters from the Hoover web site.I have installed the new brush, belt, and filters. I'm ready to install the replacement cord, but I can't figure out how to access the interior part of the vacuum! I tried removing many different screws but none of them seemed to give me access to the necessary area. Any help would be appreciated!\015

Answers :

The aforementioned solutions probably never even attempted this fix on this model. The handle does NOT need to come off. but the 5 screws on the front housing DO: 2 above the light and 3 below it. Then to get the colored housing off you need to access 2 screws on the underside that are beneath the agitator roller. To do that, obviously the 4 screws holding the bottom plate need to come off too. Here's a link to a schematic that might help as you attempt to do this, (assuming that you still do!) http://www.elkypro.com/hoops2005/vacuum_parts/hoover/U5461-900.html

Once you have the main body housing cover off, then you can access the 2 screws atop of each trunnion cover that holds the motor assembly cover halves together. If you've made it this far, then gently pry apart the motor halves keeping even as yo do. Now you can see all the wiring necessary to cut and splice. Happy cord replacing! As for me, I am headed for the store, as I am not so sure I can remember how to get the darn thing put back together. But it was fun taking it apart!
For the w.t.sp. you will first need a pair of **** , electrical tape, wire strippers and some wire nuts. on your handle you will see either (2) or (4) screws. remove these screws and handle. next take out all of your tools out from the storage place in front. you should see (4) more screws inside. once those are out the face plate will come off. cut the cord with the **** and cut the leads inside. you should see a purple wire and an orange wire. (purple goes with purple, the white goes with the orange) to put back reverse your steps. hope this help. \015\012\015\012\015\012\015\012if you get stuck write me back
Repair Help & Product Troubleshooting for Hoover U6616-900 WindTunnel Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to replace power cord on Hoover WindTunnel upright vacuum


The aforementioned solutions probably never even attempted this fix on this model. The handle does NOT need to come off. but the 5 screws on the front housing DO: 2 above the light and 3 below it. Then to get the colored housing off you need to acc ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

Hoover u6634-900 power cord replacement - Hoover U6634-900 WindTunnel Bagless Upright Vacuum


... Hoover U6634-900 WindTunnel Bagless Upright Vacuum

Video how to replace sanitair power cord - Hoover U6616-900 WindTunnel Bagless Upright Vacuum


... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

Replacing a fraayed and twisted power cord on a Hoover windtunnel upright


Ok so I took this vaccum apart completely except for the electrical and motor systems. It seems to me that without dismantling both of these systems on the vaccum you can't replace the power cord. And I wouldn't recommend taking them apart unless yo ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

Replace power cord for hoover tempo sweeper - Hoover Tempo Widepath Upright Vacuum - Blue


... Hoover Tempo Widepath Upright Vacuum - Blue

Replace power cord Hoover U5757-900 - Hoover Company Wind Tunnel U53019 Upright Vacuum


... Hoover Company Wind Tunnel U53019 Upright Vacuum

Replace vaccum power cord - Hoover Tempo Widepath Upright Vacuum - Blue


Watch this video for instructions ... Hoover Tempo Widepath Upright Vacuum - Blue

Power cord will not come out - Hoover UH70120 WindTunnel TSeries Rewind Bagless Upright Vacuum Cleaner


There is probably a crossed cord in the rewinder. I am not sure but if you can get into the rewinder you can free up the cord it should go, hope this helps. Chris ... Hoover UH70120 WindTunnel TSeries Rewind Bagless Upright Vacuum Cleaner

Replace cord on Hoover windtunnel upright vacuum


This video may help you ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Replace motor hoover windtunnel - Hoover U6476-910 WindTunnel Upright Vacuum Cleaner Bagged Vacuum


... Hoover U6476-910 WindTunnel Upright Vacuum Cleaner Bagged Vacuum

How to remove the bag housing from the handle in order to replace the power cord on a Hoover vacuum U5209-930


... Hoover Vacuums

Need to replace power cord on Hoover vacuum.


Remove the dirt container and look for screws. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Replacing belts on U3109 hoover vacuum - Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum


... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

Hoover Upright Vacuum model U5470-900 - The On/Off switch on the handle does not properly engage the power switch deeper in the handle assembly. It appears to ride over the lower switch and doesn't engage it to operate it. If I play with it, I can get it to maybe turn on the vacuum, but, then the upper handle switch won't turn it off. Our current workaround is to use the power cord for on/off operation.


... Hoover Vacuums

How do I replace a hoover windtunnel belt - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum


Here is a link to the manual and to the belts you need.\015\012\015\012\011\011\011\011\011\011U6439-900 Manual \015\012\011\011\011\011\0 ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover U5465-900 Power Cord Replacement


Click here to see an exploded view of your vacuum. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

How do I replace the power cord? - Eureka 12 Amp Capture Vacuum Upright Vacuum


... Eureka 12 Amp Capture Vacuum Upright Vacuum

VACUUM REPAIR I have a Hoover Savvy upright, windtunnel, bag/bagless vacuum (model U8150-900). The Handle Release Foot Pedal - Part #38434026 broke soon after purchase but I finally found a source to replace this item. The problem is that now that I have the repair part I cannot figure out how to remove the old pedal and install the new one. The housing appears to be one piece of solid plastic. Any ideas, PLEASE! Peter


There are 2 tabs that stick out on the release, they fit in slots, so from the top look down and you can see them, using a flatblade screwdriver that will fit in there, push the side in to release it, which isn't easy, but it can be done. When you g ... Vacuums

I'm trying to replace the power cord on my Hoover Telios vacuum cleaner. I have the machine open on the floor, but can't work out how to find the terminals on the cord rewind reel - they seem


... Hoover Telios Canister Vac Vacuum

Replace hoover belt 40201160 - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum


You usually have to unscrew the bottom and take it off to get to the belt and then you have to stretch it back on usually a quick fix ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

How to replace a Hoover Control Cable U6425 - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover u6425 switch replacement - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Belt replacement for Hoover U5100-9RM - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

I have a Hoover U3330 001 upright vacuum, while using it today the power suddenly cut out and it stopped working. I have replaced the fuse with a new and tested fuse, but the machine will still not power up. please can you help?


... Hoover Vacuums

Vacuum dead I have oreck XLx2 bagged upright - the belt ,plug and cord have been replaced - has been working great - now went to plug it in and it does not work - the light goes on in the on/off switch so power is working but vacuum is dead - any suggestions


If the cord coming from the bottom up to the handle is loose, and is a plug, push it in. If that doesn't help. then could be a problem with the motor. One other thing to check is inside the handle, maybe a wire came loose. ... Oreck XL2200 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1128 seconds