Having problems with your Hoover U6630-900 WindTunnel Bagless Upright Vacuum ?

Hoover self propelled U6630900 idler arm lock

\015 My adjustment knob which is connected to the idler arm for CARPET-HARD FLOOR came off. Now the idler arm is disconnected. How do you remove the hood assembly to reconnect the idler arm and thus the adj. knob?\015

Answers :

Remove the bottom plate (4 screws), remove belts and brush roller. There may be 1 small screw in the center front of the vac under the brush roller. remove this one. If this is a bagless model you will also need to remove all of the back screws (torx) that hold the lower hose on. This needs to be removed to take the hood off. underneath on each side of the power drive assembly you will have 1 screw, remove them. there is a clip on each side that snaps the front on, push them out with a screwdriver. Then the hood is removed.
Repair Help & Product Troubleshooting for Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover self propelled U6630900 idler arm lock


Remove the bottom plate (4 screws), remove belts and brush roller. There may be 1 small screw in the center front of the vac under the brush roller. remove this one. If this is a bagless model you will also need to remove all of the back screws (torx ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hoover Wind tunnel self propel not propelling - how do I know if it is the belt or the idler arm?


... Hoover U6485-900 Windtunnel Bagged Upright

Just replaced the belts on my Hoover Windtunnel II self-propelled vacuum. The brushes are now turning ok, but the self propelled feature is not working. Squeals when when you lock it in the upright position.


Check the plastic part, which the the self propelled cable is attached to. (release the handle, tilt it back. You should be able to see the cable attached by a screw to a black plastic arm.) It is either broken or the cable is lose. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hoover U6434-900 self-propell cable and actuator arm replacement


... Hoover U6434-900 Bagged Upright Vacuum

V-belt flapping on Hoover Self-Propelled WindTunnel Bagged Vacuum


... Hoover U6441-940 WindTunnel Bagged Upright Vacuum

Hoover WindTunnel Self-Propelled V Belt


I had this same problem with the V belt on my Hoover Vaccuum.\012\012There are three (3) basic things that will cause the brush roll not to spin.\012\0121. When handle is upright, brush roll is OFF.\0122. When switch is set for HARD surfa ... Hoover U6441-940 WindTunnel Bagged Upright Vacuum

How to repair the arm assembly that opens and closes the valve on a hoover wndtunnel self propelled bagless


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

On my Hoover 6660-900 bagless upright self propelled wind tunnel vacuum when I replaced the cable which works the power drive, there is a spring next to the control arm which I cannot quite figure ou


... Vacuums

My hoover wind tunnel self propelled vacuum wont stand up be itself. The locking thing is not working. Thank You. [email protected]


If you look at the foot pedal, see if it is locked in the base, and pivots freely. I have seen some of these that break the base, or break the spring hinge on the back side of the release pedal. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Hoover Wind Tunnel Upright Self-Propelled


Thanks to reddevil6. Sure enough it was the belt. What I did was take off the belt and flipped it over, worked like a charm. Since it was stretched on one side the other side was still ok. Still need a new, but s aved me a trip to the store! ... Vacuums

Hoover 6485-900 self propelled will not roll. Self propel switch seems flimsy and I can't tell if it's working. New vac used about five times. I can see a wire moving down near the rollers when I engage the self propel but the wheels don't turn. Thanks for any assistance you can provide.


... Vacuums

Self-propel not working on my Hoover Windtunnel


... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Hoover Upright Bagless WindTunnel does not self propel (U6625-900). Belts are new, Brush turns strongly. Wheels propel forward very weakly and do not reverse when the handle is pulled backward. Is there a mechanical link from the self propel switch to the "transmission" ? Are there any gears that could be worn or not engaging properly?


... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Hoover self-propelled wind tunnel doesn't self propel going backwards.


Your self propel cable sounds like you need to have an adjustment. reccomend a service shop repair. ... Hoover Vacuums

I have a Hoover power max self propelled vacuum. The belt that goes to the self propelled part keeps slipping off. I've had the belt replaced, but the problem persists. What can be wrong? I've taken it to a Sew N Vac repair, but all he did was replace the belt again. And it still has the same problem.


I can guess of one problembelt gets removed when motor is running right?am assuming that belt is fit tightly and fits correctly when motor is in restif so then ur motor is not running at a proper speed which can be a pos ... Vacuums

Self-propelled Hoover windtunnel (with bags) will not self-propel. Belts are all in order, but I am quite sure it has to do with the cable. How would I fix this and how does the end of the cable with a nut, connect?


This might help - go to following website and look for "troubleshooting" \015\012http://www.fixya.com/support/p40544-hoo ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Self propell doesn't work. Motor spins and belt burns, brushes do not turn. model Hoover self propelled u6425-900


May be a stripped sprocket/cog or snapped shaft. check and replace as needed. ... Hoover Vacuums

Hoover U6637-960 the self propel is not not working. When lowering the handle it acts like it would like to work but the roller will not turn. appears to be something to do with the self propel part of the handle . took the screws aout but can not get it apart. Is there another belt of something in there?


This vac has 2 belts. If both self propel and roller not spinning then most likely it is the wide flat belt broken or off. 4 screws on the bottom should gain you access to the belt area. another issue for this model series is a worn pulley on the rol ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hoover upright self-propelled drive vacuum cleaner u6331-93 will not self-propel


Here is a video how to fix ... Vacuums

Hoover self-propelled self-propel not working. belts ok.


No suction on Windtunnel 6630-900. All belts work, brush turns, it just won't pick up anything. ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

I have 2 Hoover Wind Tunnel-self propelled bagged vacuums-U6433-900 model.The roller bar does not agitate, the self propelled feature does not work and, in general, the vacuum is not performing well. I have replaced the roller bar, the v belt and the wide belt. The filters have been replaced and it has a new bag. I have had both of these since 2004 and they were fairly expensive $200 each) but if the repairs are prohibitive, I might as well get new vacuums. Suggestions? I just spent $100 for bel


The Hoover WindTunnel self propelled is a machine that we see in our retail stores (Vacuums Unlimited) constantly. The benefit of having a supposed "self-propelled" machine wears of quickly after the numerous time you will need to take this machine ... Hoover Vacuums

Hoover Bagless Windtunnel - Self Propel feature not working


I have the same problem with ours. If you lift the vacuum by the handle it breaks the lever on the transmission. You can find a replacement cable and lever on line for about $16.00 it is somewhat involved to repair but can be done by someone with mec ... Hoover Vacuums

Hoover Windtunel Self-Propelled Upright Vacuum, Power Drive Not Working


Have you checked the belthttp://www.youtube.com/watch?NR=1&v=wRoqZnZ4h0w&feature=endscreen ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Upright hoover U6617-960 will not self propell


... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

Hoover Self-Propelled WindTunnel U6436-900 cable problem


The flat belt should be changed if it has been longer than 9-12 months. Next I would remove the upper handle to inspect the top section of the control cable, sometimes it fray's and has a sponge feel (no positive control) to self propel. To set this ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0423 seconds