Having problems with your Hoover U6630-900 WindTunnel Bagless Upright Vacuum ?

Brush Roll won't switch positions

\015 The brush roll will not change from on to off regardless of whether I have the lever on carpet or hard. Help!\015

Answers :

The adjustment knob on the hood of the machine is a plastic "arm" that prevents the belt tensioner from tightening up the v-belt so that the roller will stop or start. If the knob is adjusted while the handle is back, it can break the plastic arm off and then the function will not work. This knob should only be adjusted with the handle in the upright position. Usually, if the arm is broken, the roller will still turn when the handle is lowered and will not turn off when the knob is selected to the bare floor. If the brush roll will not switch on , it is usually a problem with the belt(s). You should replace the belts yearly. They can look fine, but be worn out.
Repair Help & Product Troubleshooting for Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The beater brush wont spin because the brush roll is always in the off position. Moving the carpet/hard switch doesn't turn it on.

Hello : \015\012\015\012Try this please : \015\012\015\012 Switch the carpet/bare floor dial back & forth 5 times, ending on carpet. Tilt the handle back as if to vacuum upright & lay the vacuum on its side so it is resting ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Brush Roll won't switch positions

The adjustment knob on the hood of the machine is a plastic "arm" that prevents the belt tensioner from tightening up the v-belt so that the roller will stop or start. If the knob is adjusted while the handle is back, it can break the plastic arm off ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have an Easy-Flo central vac unit. The handle on the electric hose has a switch on the handle. With the switch on ''O'' in the center, it's off. On the left, is the ''I'' position. The vacuum runs but the power brush doesn't. On the right is the ''II'' position. The switch won't flip that way. It feels stuck. It feels as if there is something underneath of it that won't let it push that direction. I have the switch out of the handle, but I can't seem to get the actual black casing around the

Switches are not usually designed to be dissembled.I would strongly suggest that you dont take the switch apart. you are better off getting a new one. then if you feel like it you can take the old switch apart and if it dosnt work you still hav ... Vacuums

Brush roll belt stops turning when in position to vacuum. Does turn when vacuum is turned onto side. Belt is in tact, brush roll is fine. What's going on?

I think I know what the problem is with your machine. It's a rather lengthy repair, and I'll be happy to photograph it for you (like I do on most of my Fixya answers), but I'd like to know before doing all of that if you still need help, or if you' ... Eureka Smartvac 4870 Bagged Upright Vacuum

Brushes stop rolling when against carpet, yes it is out of the upright position and when I left the base off the carpet the brushes start to roll again. What is wrong?

Your belt is stretched out so it just stops when the carpet resists it. Get a new belt made for your particular machine and you should be back up and running ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

When vacuuming on position I, the motorized brush does not roll and light does not turn on.

Dont use brushes on wooden floors ,,,,this link is the manualhttp://www.sharkclean.com/manual/NV351_26_NV352_26_IM_ENG_SPA_101207.pdf ... Shark Vacuum. Navigator Lift-Away Bagless Upright Vacuum Cleaner NV352

I need a new brush bar, The end (plastic) brokeand the brush wont roll!

You can try your local vacuum shop or look online at either eBay or amazon.com. There are also websites like govacuum.com or vacpartswarehouse.com Here is a link: ... Dyson Ball DC24 Bagless Upright Vacuum

Spin brushes wont spin and the switch wont turn machine off. I have to unplug it. 

For the spin brushes it is most likely the motor is fried if you smell something burning it could be jammed or the wires have be shaken off the motor terminals. for it not turning off you need a new switch. ... Hoover F7431-900 SteamVac Vacuum

On/off switch works but wont stay in on position unless you hold it down cant see how to get in to the switch this is on dc17 animal

This link will show you how to chonge the switch on your dc17\015\012http://www.videojug.com/webvideo/how-to-fix-the-lead-on-a-dyso ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dirt devil plat.force brush roller wont roll on carpet

... Dirt Devil M091200 Platinum Force Upright Vacuum

M1300 i dirt devil brushes wont roll

The brush roller itself has crud jammed in it. it is not the belt. the smell however - is the belt being burnt as the small metal axle tries to turn the who unit - but the belt wont move - so the small axle spins and burns into the belt. this can bur ... Dirt Devil M130000 ''i'' Dual Cyclonic Upright Vacuum Cleaner Vacuum

Eureka 4870 brush won't stop turning in upright position

There will be a linkage that as come loose and not operating the limit switch to turn it off, try looking at 23. Idler Clamp Assembly on the link below. ... Eureka Smartvac 4870 Bagged Upright Vacuum

Brush roll wont turn

Might be that the the idler wheel is stuck and not engaging the V belt. If you look down just past the V belt you will see a black roller, it needs to be against the belt. It is either stuck or the asm. is broken. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Roller brush on/off switch on hoover windtunnel u6401-9rm broken

... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My dyson wont turn the brush roll back on

Hi there,I'm sorry to hear you're having difficulty with your DC18. You may need to reset the brush bar motor - this is simple to do, so please follow the steps shown in our online Support guide: ... Dyson Vacuums

Rotator brush not spinning. Handle is not in the locked upright position. Says it's beltless, so is this likely an interlock switch or drive motor problem ?

Hi, the brush roll will only spin when your handle is not in the locked upright position, once the handle goes upright - the brushroll de-activates ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Bissel home healthy vac. The brush only turns on for a split second and shuts off. Each time I put it in the upright position and start over, it does the same thing. I thought it may be the switch up on the handle. I replaced it, no luck.

Here is some information about a second Auto Cut-Off Switch near the power switch:\015\012About the only "gripe" I can come up with has to do with the automatic brush shut off mechanism that causes the brush to stop rotating when the unit is mo ... Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum

Just got my dc33... one issue... the dial switch to control btn bare floor / carpet mode doesn't seem holding in it's position when I set to the bare floor mode... it keeps coming back to carpet mode with brush-bar activated... the dial doesn't really click to the floor mode. Any advice on this?

Hi there,I'm sorry to hear you're having difficulties with your DC33. If you're concerned that the brush control doesn't seem to be staying in position, it's probably best if you get in touch with us directly. One of our experts will be h ... Dyson DC33 Bagged Upright Vacuum

Power head motor is good,runs great from test cord switch seems to work. brush roll cleaned but power head motor will not run

If you have checked the power delivery down to the powerhead and you have current running to the powerhead, then you likely have a burned fuse. There is a fuse built into the powerhead motor and is usually located on the field winding. This is not ea ... Eureka 6831A Bagged Canister Vacuum

I have a bissell lift off and the brushes wont spin, i think it maybe because of the internal switch that tells the vacuum that the canister is installed is bad. is there a replacement part for that or do i have to get a new vacuum?

Hi,If you take out the brush roll, holding the ends, make sure that it \015\012spins freely, if not, replace it. Belts stretch after a short time of \015\012use and need to be replaced often.So you could either have a bad brush roll and ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Motor wont turn on.I checked the switch and I think it is working.motor turns on if a put direct power to it.'but it smokes at the brushes. can you help?

This sounds like either the belt isn`t on right or the brush is not slotted in the vacuum right remove the plastic or metal cover from the bottom and check by inspecting the belts ability to easly turn the brush rod check with your hands DO NOT turn ... Kirby G4 Bagged Upright Vacuum

When switched on the brushes dont go round and it wont **** up but when i use the handle to clean theres suction there does this model have a belt?

It has a brushroll and transmission i think. turn the top screw and rotate til the end of the nozzle comes off. then pull the brushroll out from each side see if the shafts on the transmission are rotating and also check the inside of the brushrolls ... Dyson Ball DC24 Bagless Upright Vacuum

Kenmore 116.35922500 brush wont turn. Seems to come on if handle angle is held at just the right position but it is intermittent. Reset button is not popped up and doesn't seem to have any effect.

... Kenmore Vacuums

I have a Bissell Proheat 2x cleaner which has worked perfectly on every occasion. Today I filled the machine as usual with water and formula and switched on, the motor ran, the lights were on and the brushes rotated but upon pressing the spray trigger no water or formula was released. I have cleaned the jets underneath and also followed instructions to release any airlock. It still wont release the water/formula. What else can I do? Thanks Charles

Please check the following with liquid in both tanks.\015\012 \015\012- Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.\015\012- ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The brushes wont turn. every thing is cleaned and the switch is in the correct seting

Check belt ... Hoover F7220900 SteamVac V2 Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0790 seconds