Having problems with your Hoover U6630-900 WindTunnel Bagless Upright Vacuum ?

It seems when i am vacuuming it is very hard it move and the brushes does not rotate after the rug strings got into it.

Answers :

Your belt is stretched or worn and therefore cannot turn against the resistance of the carpet. If you replace the belt it will fix the problem. You can get the belt you need here:

Repair Help & Product Troubleshooting for Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

It seems when i am vacuuming it is very hard it move and the brushes does not rotate after the rug strings got into it.

Your belt is stretched or worn and therefore cannot turn against the resistance of the carpet. If you replace the belt it will fix the problem. You can get the belt you need here: ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I ran over a big floor rug with my vacuum and some of the strings from the rug got tangled in the roller on the vacuum. It makes a terribly loud noise even now after I have cleared the strings from the rollers. What else can I do to get rid of the loudness?

Loose area rugs should never be cleaned with any revolving brush vac. They will damage the rug by destroying the fringes and corners. In some cases the brush will also pull out tufted as the rug is made so poorly. Natural fiber rugs should never have ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I ran my vacuum against an area rug that has strings around it and a few strings got caught up in the beater bar. Now, the beater bar does not function- the motor runs but the beater bar does not seem to be operating. I removed the strings from the bar.

Hi,\015\012\015\012There is a switch next to the main power switch on the handle which turns the brushbar on and off. When the beater bar becomes obstructed as in your case, there is a safety feature which cuts power to the beater bar. Al ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Roller does not turn; I was vacuuming a rug and a string got stuck in roller-took it off but now the roller will not turn. suction is fine.

The roller drive belt may be stripped, worn partway through where it goes around the motor shaft, thrown off the motor shaft, or broken. Take the bottom plate off the carpet sweeper and have a look.If the belt was damaged when the roller ... Kenmore 25512/ 25513 Progressive Canister Vacuum

While using my Dyson a rug got caught and that ratcheting sound started. I removed all signs of strings, etc until the brushes rotated fine but when I started the Dyson the ratcheting started again. I have the DC 14 Animal.

The rattly sound means the drive belt has snapped or the protective clutch has slipped. This needs repair by someone who knows how to repair Dysons officially. Sadly its the kind of model that can't be done by the owner. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help

The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Roller brush does not rotate if there is a belt I can't open that part of the vacuum to look. Vacuum is new but I vacuumed a string that caused the brush to stall for a moment. I could smell like when a belt gets hot or burns it's a surfacemax 300.

You need to replace the belt. Replacement Vacuum Belts ... Vacuums

Electrolux vacuum brush not turning problem: was vacuuming and rug got caught auto shut off kicked off power to brush. instead of hitting red button to restart brush I disconnected brush to vacuum some hair in Conner. after i reconnected the brush and hit the red button but no power to brush. Light won't even switch on. Hope you can help

Under the vacuum, there is a guard.\012remove the guard , either by 2 screws or by 2 clips.\012there is a belt under the guard.\012that is connected to the brush.\012the belt need to be replaced. ... Vacuums

I was vacuuming, and ran over an area rug with those tassle things on the end. the brush immediately stopped spinning. so i turned the vacuum off and un-tangled the brush. after replacing the brush and putting the assembly back together, the brush no longer rotates.

Did you smell something burning? You probably melted/broke the drive belt. ... Dyson Ball DC24 Bagless Upright Vacuum

Got a Panasonic Eco max vacuum cleaner model mc-ul952.Brush bar does not rotate when switch set on ''carpet'.Brush bar clear....rotates freely by hand

... Vacuums

I just accidently vacuumed over a bag, realized what had happened and pulled it out before it got stuck further into the head of my Hoover Wide Path. I shut the machine off, and when I turned it back on the brush won't rotate. Anything I can do?


Dyson DC07: When I first got this vacuum, it was so powerful that it lifted my area rugs off the floor. It is so weak it barely works. I have removed and cleaned the filter, but I can?t seem to improve the suction. What am I doing wrong? How do I fix it?

Hello,\015\012\015\012If your vacuum runs but still leaves dirt behind, the culprit could be the drive belt or an obstruction. If the agitator brush slips or won't turn, the belt is bad and needs to be replaced. If suction is weak when yo ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Hy, I have a dyson 14 that sometimes make a terrible racket when I am vacuuming rugs. This happens even after I've cleared the roller brush of strings, hair, etc.

Check the beater bar to see if it turns freely. It should spin real easy. If it takes just a little effort, your problem would be the beater bar is binding on one or both of the end caps. When the bar gets bound up, there is a clutch with three ba ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Vacuuming a small rug and it got sucked up a bit and now my extension won't work.

Make sure the little red reset button is pushed in on the power nozzle. ... Rainbow 75th Anniversary Canister Vacuum

Roller not turning when I drag vacuum across the rug. Got something caught in it, pulled it out, then stopped working properly.

Check the belt and what got stuck in it ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Simplicity S24 canister vacuum. It's about 3 yrs. old. In the past year I have had it in the shop 4 times because when using the rug piece, the piece turns on & off, on & off. The actual vacuum doesn't... just the rug piece. I recently spent $65 on a new part, after spending countless dollars the other 3 times it was in the shop for this problem. I'm ready to buy another name vacuum altogether as I feel this vacuum is not worth the money that was spent on it. I'm very frustrated.

Repair shop has not fixed the problem? complain until they fix it properly. This is a pressure fault / jamming issue or slipping drive. Repair shop should have fixed it 1st time. ... Vacuums

Caught shoe string in roller brush, now will not rotate roller BR

Belt maybe streched and hardened from heat replace and try again. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi

Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum

I was vacuuming and my electrolux 2100 accidentally suctioned the string attached to a balloon. I turned off the vacuum and unwrapped the string from the head of my vacuum. On the hose i have plenty of suction but the head isn't working. i flipped on and off the emergency shutoff switch but it is not working. what happened? what can i do?

... Electrolux UltraLux 2000 Bagged Canister Vacuum

Rug Beater isn't rotating during use

This defintiely sounds like your belt has broken or slipped off the motor pulley. The brushes on your vacuum are driven by a belt that attaches to the motor shaft on one end, and the roller brush on the other end.\015\012\015\012If yo ... Bissell 6594 PowerForce Bagless Upright Vacuum

Roller Brush on Electrolux Nimble vacuum not rotating.

... Electrolux 5740 Upright Vacuum

My Rainbow SE vacuum was working fine until I ran over the edge of a rug and it went in to the nozzle. I immediately switched the vacuum off and proceeded to move the rug. When I tried to turn the Rainbow back on the brush was no longer spinning. I've tried the reset button and checking the nozzle for any debris, there are none. The brush just won't spin.

Hello lilbutmunch1,\015\012The brush is motor/belt driven so you probably either broke the belt or it shifted off the motor or brush shaft. I suggest you unplug it,flip it over and look for screws that hold the baseplate together.. remove those ... Rainbow E series Canister Wet/Dry Vacuum

I have a Hoover Steam Vacuum, All Terrain, and the bristle brushes are not rotating. They appear to be seated properly and, the entire vacuum is clean and free of lint, hair etc., so everything is working properly except the brushes do not rotate. Any help would be greatly appreciated. Thank you.

I checked the owner's manual and the parts breakdown for your model F5807. Both showed that your model has a stationary brush strip and not rotating brushes. Is F5807 the correct model number? ... Hoover F5807 SteamVac Wet/Dry Vacuum

My Dyson vacuum brush does not rotate even though the

Hi its Darran at Dyson. Please contact our Helpline on 1866MYDYSON as it sounds as though we may need to arrange for the machine to be repaired. One of our advisors will be able to run through some checks over the phone with you so pleas ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Loud noise I have a brand new Dyson and it is great on all my floors except one of my area rugs when it starts making this really loud vibrating noise. I am not sure why - nothing is stuck in the roller or vacuum and it doesn't make it on any of my other rugs. Also it is really hard to push whereas all the other floors it just glides. I don't want to return it but I also don't want to hear this sound every time I vacuum.

This is the clutch as it jams up in the brush. Usually happens with rugs that are not secured to the floor. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0934 seconds