Having problems with your Hoover U6630-900 WindTunnel Bagless Upright Vacuum ?

The brush on my hoover windtunnel will not turn.. I checked the v belt and it seems like its intact .. is it suppose to be inside the groove or just on the grove..it seems loose laying on the grove

Answers :

Thats why the brushes wont turn,, the belt is slipping put a new belt on then try again,,,
Repair Help & Product Troubleshooting for Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The brush on my hoover windtunnel will not turn.. I checked the v belt and it seems like its intact .. is it suppose to be inside the groove or just on the grove..it seems loose laying on the grove

Thats why the brushes wont turn,, the belt is slipping put a new belt on then try again,,, ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Brushes will not spin on the carpet. When I turn it upside down, the brushes assembly seems to be loose (or maybe it's supposed to be loose?)

That is normal also when the hanle is upright ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Both of the wheels are wobbly and loose on my Kenmore upright vacuum model 721.37060. I don't see where I can remove them to analyze and fix the problem, which seems to be that the wheels are loose on their axels. How do I get the wheels off and what do you think I'll find inside?

Most if not all vacuums have an access panel on the bottom.It may be held on by a couple of big plastic clips,the kind you squeeze together and it releases a door.Some have plastic screws.There may also be a couple of phillips screws along with it or ... Kenmore Vacuums

We have just unpacked and put together a Hoover SpinScrub SteamVac and the handle seems very loose. Is this the way it is supposed to feel?

There should of been some long screws that were on the handle itself or the manuel. these screws are what hold the handle to the machine. ... Hoover F5826-900 SteamVac Upright Wet Washer

I just purchased the hoover steam vac model F5853-900 from a garage sale and everything seems to be working well except i dont see any steam coming out from anywhere and the water in the vacuum stays cold. is there supposed to actually be a steamer inside this vacuum? if so, is there a button i need to turn on for the steamer to work? thank you so much for the help!

... Hoover F5837-900 SteamVac Supreme Wet/Dry Vacuum

HELLO I have an Oreck Orbiter Floor Machine, It makes a lot of noise. I seems like one of the side screws fell out. I did not see this happen. Nor did we see any loose hardware. My question is - How do I take it apart... to inspect inside. thanks SUsei

... Oreck Orbiter Floor Machines ORB-500, ORB-550, ORB-600 Vacuum

My ready tools dial on keeps coming out, when I put it back it it doesn't seem to be doing anything but just plugging the hole is it suppose to connect to something inside the machine

... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I have a DC14. About a wk ago it was making loud sound and bar stopped turning. i unclogged everything....now the suction works great. However, the bar still wont turn. The belt inside is still intact and isnt loose. Several solutions suggested resetting the "Red" button...i have searched the vacuum over and over. there is NO red or any other color reset button. The bar is set down perfectly in there, the cover plate is installed properly. What other problems could there be? Or do i just need to

... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The brush won't roll so i guess i need a new belt. the one there is intact but seems loose. Any other suggestions? Thx. Lynn eureka the Boss Model 405 and type B1.

... Eureka Boss SuperLite Bagless Upright Vacuum, 405AVacuum

I removed the filter from its compartment in the base of the vacuum. There are two strips inside the compartment that seem to be coming loose and that obstruct the new filter as I try to replace it. How do I fix this?

... Dirt Devil Reaction Twin Cyclone Upright Vacuum

My magic blue vacuum has no suction. The lid seems loose and the lack of suction seems to be related to the loose lid. I cannot find a way to tighten the lid.

Have u tightened the dirt cup lid. ... Vacuums

I have my Emerson FR966T wine coller set for 60 degrees, but my cooler never seems to get the high. It always hovers around 58-59. When I heat my house up (never above 68) my cooler seems to warm up to 60 (inside). Whats up? Why does the outside temp. affect the inside. The manual says it works best when the ambient temp. is 77 or lower.

... Vacuums

Hoover Wind Tunnel 7500 Brush not Turning. I have replaced the Brush and the belt. The problem does not seem to be either to me. I believe might be a missing part. The place were the belt hooks on is a metal pole which never seems to grip the belt well. In fact it seems loose most of the time and slips on the brush, causing the belt to eventually burn up. Could there be a missing plastic or rubber piece meant to hold the belt taught  on the metal pole?

Check the Idler Pulley part Number 43241004 (Item 13 in the IPB) ... Vacuums

I replaced the belt in our Eureka Boss Smart Vac, it still seems loose, it uses a type R belt. The beater belt still doesn't seem to turn properly and seems that it doesn't pick up very well when I use it on my berber carpet. We have 2 dogs and I like to use it frequently. I have changed the bags and belt......

Check to see that the beater brush is not frozen up. Pull the brush and clean it, spraying some WD40 on each end piece that holds the brush in place.\015\012Also be sure the belt is properly installed so that the brush turns in the correct direction ... Eureka Vacuums

Brushes are not rotating, V-belt seems too loose

V-belt suppose to be loose (according the manual). I just replaces it (and was worry that it is loose), but brush rotating fine. So your problem is somewhere else. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

When running the 2100 Electrolux vacuum, it is stopping and starting when pulling or pushing the floor attachment. Seems like the connection at the top of the handle is a little loose or the electric tabs are loose where the hose connects. Any ideas?

Other option is that on the hose end of the electrical connection, you can use an awl on the electrical connections to bend them in slightly so they make good contact when they are automatically plugged in when you connect the wands. HOWEVER, ONLY D ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Loose wire ive got a loose wire inside my vax cyclonic 1700w and ive stripped it down but cant see anything and its still not working but it was working when i moved the wire from side to side. Please help

Sounds to me like you have a open wire. There is a break in the wire inside to the insulation and as you move it, it gains and loses connection. You can test it with a continuity tester as you move the wire or just replace it to see if that solves th ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

The brushes will not rotate on my hoover vacuum. the belts are in good shape, the motor is turning the vacuum motor, but the belt on the brushes seems loose. I ordered a replacement belt but still nothing. Their is a small "idler" but their dosent seem to be enough tension on the belt. Any ideas?

Did you order the correct size of belt? These are the belts you should have:Hoover Windtunnel Belts ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I cannot seem to replace the beater bar on my Dyson - it seems to spin OK, but when I turn the vacuum back on and turn it to the 'Carpet" position, it makes a noise that is unbelievable. What's up with that? The belt is intact.

Sounds like its the clutch to me if it sounds like a rapid clicking and you have a large knob on the side of the cleaner head it is going to be the clutch this is a hard part to changed without the know how to do it and it is very easy to break the o ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My Bissell doesn't seem to be vaccumming as well as it was before. Not sure what the issue is. Could the belts be loose? They are on there, but not extremely tight. Should they be tight? The brush on the bottom seems to have a lot of play/bounce to it as well. Thanks for the help.

You have a partial or complete clog of the hose that carriesthe drit from the floor to the bag or other storage device.\015\012\015\012Clean it and you will regain the power you originally purchased. You may have to remove some parts to ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Filter I bought this Hoover a few years ago-- just now about to use it first time. I cannot find my user's manual and don't know how to change the filter-- or to clean it or whatever I am supposed to do with it. Also, there is a handle on one side of the unit that seems to be attached to an empty chamber or canister kind of thing. It looks like it should pull out, but it does not budge. I really would like to have a manual, but can't seem to find one. Is there a similar model that is still

This is not for the exact same model, but should help you out:\015\012http://edge.maytag.com/epipubs/56511B47.PDF ... Hoover U8143-900 Upright Vacuum

Filter queen 95X (1991) Motor is noisy but still work fine. Can there be a loose screw inside ? Can I open the motor and look inside ?

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=766802\015\012Generic problem for all Vacuums\015\012Filter queen 95X (1991) \015\012Posted by alexun o ... Vacuums

The handle seems to be loose and the self propelled function no longer seems to be functioning

Handle is suppose to be a little loose. s.p. function not working, try changing the flat belt p# 38528035 or pk # 40201170 (2) ... Hoover U6434-900 Bagged Upright Vacuum

Drive lever the neutral/ drive lever does not engage. seems loose. I have open up the bottom of gear area and have a loose bracket,how does it go back together, need a parts diagram?

Assembly instructions (lots of pictures) HERE. ... Kirby Ultimate G Bagged Upright Vacuum

Bissell 7901j pivot arm loose on non belt side - retaining clips look ok but loose part inside base - likely broken part? - and how to dis-assemble base (Maint manual?)

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0697 seconds