Having problems with your Hoover U6630-900 WindTunnel Bagless Upright Vacuum ?

I have a model s3765 Hoover Windtunnel and it was no longer suctioning like it used to. I wanted to see if something was stuck in the rollers. I undid the screws at the base 3 of them and now I see there is a pic that do not undo these screws. I am having problems with getting them back in.

Answers :

If you can post a pic of which 3 screws you are talking about and where you took them out of i can help u get it back together
Repair Help & Product Troubleshooting for Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a model s3765 Hoover Windtunnel and it was no longer suctioning like it used to. I wanted to see if something was stuck in the rollers. I undid the screws at the base 3 of them and now I see there is a pic that do not undo these screws. I am having problems with getting them back in.

If you can post a pic of which 3 screws you are talking about and where you took them out of i can help u get it back together ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I want to open a Hoover S3825 Elite Cyclonic Vacuum to see if I can repair or replace the cord reel assembly. Currently the reel slowly draws the cord back into the canister once it is pulled out. I found the mounting screws under the rear wheels once I removed the hub but I do not know how to remove the rear wheels, everything is plastic. The front screws are under the front caster wheels and I think I need to take a screwdriver and pry off the little cylinder wheel to get to them by rotating

... Vacuums

The TechDrive Pedal on my Kirby G6 fell out of the back of my vacuum cleaner. I removed the screws from the metal plate one the bottom to try to see if something had come a loose. Can you send me a diagram so I can put it back together or tell me where I can get a service manual. The only part I am having trouble with is the metal piece inside that engages the power drive. Thank you.

The pedal drive fell out . Do you have a manual telling me how to get it together again.. Thanks, Dianne ... Kirby G6 Bagged Upright Vacuum

My electrolux ambassador power wand quit working. I replaced the switch that shuts it off when the roller stops, but it wasn't the problem. The on/off switch is fine, the motor is fine. We have traced the problem to the wires inside the canister by opening the inside cover to the bag container. We see the power cords going into the canister but we're not able to get to anything. We can't find any screws to undo that would open it up in order to follow the wires deep into the canister. We've bypa

... Electrolux Vacuums

I was changing a light bulb with one of those metal extension rods that unscrew and screw back in the replacement bulbs. It evidently didn't seat correctly and pulled off the bulb and created a quick "poof" type electrical short. I have switched out that bad bulb with a new one and can't get either the fan or lights to work. There doesn't appear to be a reset switch. I also swirched out the wall switch to see if that would make a difference and it does not. Any thoughts or ideas would be appreci

If you have not already done so, I would check at the fuse or circuit breaker panel to see if you have blown a fuse or tripped a breaker. ... Vacuums

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help

The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a window fan with two fans in it & I cannot get the cover or back off so I can clean it. I* have taken all the screws out that I can get to , but there are two clamps that I can't get off, I'm not sure why the clamps are there but they are on the side with the accordian extention. Please tell me how to get it apart - after 2 years it is really filthy!! Thank you, Janet

Remove all the screws, pry clips off that hold on the extensions, than fan will pull apart. The clips must be pried off. They will not break. Then remove screws holding in the fans and remove them as well. Fairly simple process. ... Vacuums

Took apart my cleaning brushes and all on my bissell spotbot i need diagram of how to fit the head part back to the machine. I had a problem with the auto not working i have fixed that problem just need to see so that i can get it back togoether. I assembled the whole wheel back but cannot caonnect it to the machine LOL

... Bissell 1200A SpotBot Pet Robotic Vacuum

Is there a diagram/picture to help me visualize how to put cleaner belt back in vacuum? I was taking base of vacuum apart so I could get rid of hair that were wrapped on the roller. The cleaner belt came to loose and I could not figure how to fix it back. the model is eureka upright bagless series 430

Hi,Sorry to hear your belt fell out. Not good if you've never replaced a belt before...Here is a website where you can read a detailed description of how to change a belt: http://www.ehow.com/how_8034505_eureka-belt-replacemen ... Eureka 431A Optima Bagless Upright Vacuum

I have a Necchi LYdia 3 machine type 544 The motor was overheating and I removed the bottom cover and examined the motor .It looked fine and ran well. It worked OK for a time and then got hot.I was able to partially remove the motor for inspection.I found that the cooling impeller was not secured to the shaft,I tightened the set screws and reinstalled the motor. In process of getting the drive belt back on I turned the wheel that extends out of the case to index the screw that attaches the bobb

Good day!Please try to re align the motor position.You have to do is repeat the procedure that you take to remove the motor and double check the alignment because all motor in misalignment is very hard to turn.And ... Vacuums

I am trying to replace the cable and actuator on a Hoover windtunnel self propelled vacuum. but I cant get the top or hood off the get to them, I have removed all the screws I can see, roller, belts..what am I missing?? thanks so much for any help

Hi there SmartAlec from NelsonVacuums.com.au here. You will need to remove the knobs for carpet/hard floor selection and the carpet height to remove the cover they act as k ... Vacuums

Eureka 2961AVZ Will not start ...I get a momentary flicker of power about every 3d or 4th time that I flick on the power sw. Outlet is fine / Plug looks good / chord looks good / I see no obstructions ........Would appreciate any helpful thoughts ....Trying to get Mom's Eureka 2961avz back up and running. Thanks

CAREFUL! This is how my problems started. The cheap switches (and wiring) Eureka is using in some models, especially my model) should provoke a lawsuit imo.Here's my story, just in case it might help. Mine started with a problem very similar ... Eureka 2961AVZ Bagless Upright Vacuum

I also have a Hoover upright and I need to replace the electrical cord. I have dimantled the back, where the tools are stored, and the hose. I still cannot find the screws or whatever, to get to the area behind the cord, so I can replace it. I think I will have to take off the bottom too. Has anyone out there tried to do this? It seems crazy. This machine works great so I hope I can also put it back together. Thanks for the help.

Since I do not know your specific model I can only supply you with general instructions. Be aware that most of the time you only need to gain access to the on/off switch to replace the power cord. Also Make sure that you are replacing the existing co ... Vacuums

The valve pipe assembly just popped off our Dyson DC 17. How do I get it back on? I see it appear the arm of the assembly needs to be captured but I can't figure how to get it all lined up without forcing it together.

... Dyson DCO3 Absolute Bagless Upright Cyclonic Vacuum

I have a windsor vsp 14, it is making a bad grinding noise, when I take the top blue piece off it stops, the brush works fine and when I put the top back on it grinds really loud and gets hot. it still vacuums and the belt and brush are working fine, can't figure it out. and when the lid is on I cant see what its grinding on. It only makes a grinding noise when you pull handle back and engade to vacuum flor and stops when you put it upright.

... Windsor VS14 Versamatic Bagged Upright Vacuum

My vacuum cleaner is making a loud squealing sound when I turn it on and the brush is turning. It gets louder while vacuuming the carpet. I tried to remove the bottom cover to see inside but, took out a bunch of screws and couldn't get the cover off.

... Kenmore Progressive Direct Drive 30912 Vacuum

Dead motor I purchased a new motor for my Dyson Animal but I cannot figure out how to get the thing apart to replace it. There are weird star shaped screws but I can't even see how removing those would get me where i need to be. HELP!!!

Ace Hardware or Home Depot should have your star screws ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Good day, I took off the cover on a proheat upright, to install the suction diverter flap. Guy at the shop told me I had to do this but I don't think it was really necessary. Anyway, I am having a real job getting the cover back on. The shampoo mix piston seems to be causing the problem seating the two halves correctly. I see no obvious "right: way to put the piston back in. can anybody help me. Thanks Richard

Hey Richard. Turn the shampoo mix dial so the spiral is all the way at the top when you are looking at it from underneath. then, you want the piston to seat in the top groove of the knob. You want the piston's end that jets out to fit in the space ... Vacuums

I have a Hoover Slider, Model #S2105, Serial #050500084989, and I need instructions on putting it back together; with parts and assembly of parts. I took it apart because it was making a noise, and I believe one of the belts had come off. However, when I took the screws out of the bottom to check the belts, the whole thing fell apart. Now I can't get back together properly. It will not come on, and I believe it is because the switch that makes it come on when you lower the handle is not posi

Greetings from GoVacuum,\015\012\015\012Please see the link below for a parts schematic to your Hoover Slider, hopefully this will help you put the machine back together. If you find a part that is missing, and would like to order one, j ... Vacuums

I installed a new battery in my Roomba 540. It charges and runs directly with power cord but will not charge on dock. When I push the dock button, it acts like it "sees" the dock and approaches it and even slides on, but then gets back off again and just keeps going back and forth until I turn it off.

... Roomba Robotic Floor Bagless Vacuum

The brush is not moving on the vaccume. I'm pretty sure that the belt is busted. I cannot see how to get the shroud off, so that I can get to the roller and belt. It all looks and feels like one piece, even when I start removing screws. It is a bag-less vac. The model number is - v1310rs. Thank you.

I know on my Eureka I had to remove a couple of screws on the bottom and then get a flat blade screwdriver and wedge it on each side of the base kinda next where the end of the roller would be and it snaps up and off. Really weird I thought but that' ... Euro-Pro Shark Professional Upright Vacuum with Bonus StickVac Red Bagless Vacuum

Hoover Wind Tunnel U6458-900 Self Propel doesn't work - via other expert advice here for other models of Hoover - I'm thinking it is the actuator that needs to be replaced as I can see the cable does not connect to anything on the bottom. My problem is - I can't get the cover off. Been trying for a couple of hours. I removed every screw I can seem to find but something is hold it down. I also am wondering if/when I do eventually get the cover off, would I need to replace the cable when I replac

On some models there are hook/springs that hold the cover of the base snug. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a sta rite (pentair) cristal high rate sand filter model T-200-BP-1....its leaking water thru the top of the valve, where the valve cover screws on the valve body assembly. it leaks water out where they go together around the screws. Also when i vacuum it, everything that i vacuum gets washed back in the pool when its on the filter position. Also the backwash leaks when its turned 2 the filter position, does it supposed to do that?...the only way i have gotten it to stop is to put a seper

... Vacuums

I am trying to replace the belt on my bissell. The directions state "remove the screw that holds the red retainer in place, set red retainer arm and screw aside. I see the red retainer but can not get it out I also can not remove the black brush arm that holds the brush in place. I have tried and can not remove it.

Hi, Did you release the handle first before you flipped it over?Have you removed the screw and it still won't come out, or is it stuck even after the screw is out?Are you having trouble getting to it?Please r ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I am getting very little suction from the motor. The hose is clear, the bag new. When I open the bag cover, plug the hose in and turn the vacuum on, there is next to no suction from the motor. What do you think is wrong? How do I remove the cord retractor to get to the two screws that hold the back of the canopy cover?

Your problem is probably is you don't have a proper seal in your chasis. A vacuum has to be sealed tight or the air will leak out and the seal broken. Check around the whole body after the bag is in and check for any airflow noise. I could help more ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0991 seconds