Having problems with your Hoover U6630-900 WindTunnel Bagless Upright Vacuum ?

I have the bagless hoover windtunnel and it doesn't pick up anything and it is very hard to push. Changed the belt and The rollers are spinning and the filter has been changed. What else can I do?


Answers :

It sounds like there are dirt and hair wound around the wheel axels cousing them not to spin freely. You have to remove all hair and carpet fiber. Then drop a drop of lubricant oil on the axel.
\015\012Change the filter.
\015\012You should even Check the floor nozzle for clogged dirt.
\015\012
\015\012BR
\015\012Bruce
Repair Help & Product Troubleshooting for Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have the bagless hoover windtunnel and it doesn't pick up anything and it is very hard to push. Changed the belt and The rollers are spinning and the filter has been changed. What else can I do?


It sounds like there are dirt and hair wound around the wheel axels cousing them not to spin freely. You have to remove all hair and carpet fiber. Then drop a drop of lubricant oil on the axel.\015\012Change the filter.\015\012You should ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have an Oreck XL Platnium. It smells like burning rubber and the brush roller binds and stops as you pull it back and forth, even on a hard floor. I have changed the belt 2 times. I have taken the brush roller out and checked it. It seems to be spinning freely. What could be wrong??


... Oreck XL Ultra Bagged Upright Vacuum

When we changed the belt the new belt broke right away and the brush roller wouldn't spin. My husband cleaned off the roller and got it moving slowly again, but when we went to re-attach everythin


The thing you call wheels are actually called roller bearings that fit at both ends of the brush-roll there probably seized up you can get a new brush-roll with bearings from the link below. ... Dirt Devil Breeze Bagged Upright

Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the


... Dirt Devil M088905 Vision Bagless Upright Vacuum

Have ultra vision and have changed filter and foam filter, checked all hoses but still will not pick up. Belt is fine and brush is clean and spinning properly. dirt stays at top of filter instead of falling into canister.


My kids get mine stuck all the time :(Take the vacuum outside then:Remove the hose at the bottom and see if there is any obstructions. Also shake the hose to make sure there is nothing in there as well or take it out side and make s ... Dirt Devil Vacuums

I have a dirt devil featherlite plus and all of the sudden it started pushing hard and smells hot. I cleaned the roller, changed the bag, checked the belt. The belt is a little wore, but not bad.


If it is pushing hard then you still have a belt problem. It may not be broken but the belt is stretched out too long and will not turn the roller brush fast enough to make it push easy. ... Dirt Devil M085500 Featherlite Plus Bagged Upright Vacuum

My Dyson DC24 will not pick up despite the rollers are spinning.(i have cleaned the rollers) All the filters have been changed. When usng the hose after a second a loud hiss can be heard and then no suction. Please advise


I have the feeling you have something stuck somewhere at the hose. carefully use a clothe hanger and clean inside the hose. use a flashlight to see the object. ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Changing belt how do you change the belt on the power steamer there is nothing on bissells webiste i need to change the one on the sie not the rollers


Take the water and solution tank out of the machine. turn it over an on the left hand side you will see a red clip with a screw in it. take out that screw. flip the unit back over and take off the belt access cover by sticking a straight screw dri ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Change belt How do I change the belt. I took the bottom off and removed the roller but can't get the rest apart to get to the place to hook the belt on the the drive.


... Hoover U4270-930 Vacuum

Bissell Power Track Cyclonic Upright Bagless Vacuum.. ..The spin brush works laying down....when upright it won't spin! I cleaned any and all hair from the roller....belt is not broken....but do I need a new belt though? The vac is a few years old bever replaced the belt yet.


You need a new belt. ... Vacuums

Hi,dyson dc25 overdrive,my brusher's wont go round,i have cleaned the brusher's and filter,loads of suction.the belt is intact and the roller move's feely by hand,could it be the switch


Hi Stephen,I'm sorry to hear you've had difficulty with your DC25 Overdrive. If the brush bar won't rotate, and you've already checked the cleaner head is free of obstructions, it's likely it just needs resetting.You might like to tak ... Vacuums

My eureka 5902 4D bagless uprights roller brush stopped spinning. The belt is ok. This model has a sliding switch for roller speed. The brush should spin when you release the handle via the foot release. Bad brush motor or is there a fuse involved?


The same thing happened to me about a year ago with this very model. \015\012The issue on mine was a small, copper-colored metal wheel that attaches to the end of the brush roller. You'll need to remove the top cover (there are several screws). ... Eureka Smartvac 4870 Bagged Upright Vacuum

The roller is not spinning. I took the bottom screws off but and replaced the belt but am not sure how to replace the clutch. I think that is what it is anyways, the thin silver bar that controls if the roller is spinning or not


... Riccar 8850 Vacuum

No spin Vacuum's brush does not spin on (low) carpet unless switched to "high" but then roller does not pick up hair on carpet. Belts are in good condition. Maybe belts are loose?


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=40485&thid=782631\015\012No spin\015\012Posted by erin_david on Jul 14, 2008\015\012Vacuum's brush does no ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have 2 Hoover Wind Tunnel-self propelled bagged vacuums-U6433-900 model.The roller bar does not agitate, the self propelled feature does not work and, in general, the vacuum is not performing well. I have replaced the roller bar, the v belt and the wide belt. The filters have been replaced and it has a new bag. I have had both of these since 2004 and they were fairly expensive $200 each) but if the repairs are prohibitive, I might as well get new vacuums. Suggestions? I just spent $100 for bel


The Hoover WindTunnel self propelled is a machine that we see in our retail stores (Vacuums Unlimited) constantly. The benefit of having a supposed "self-propelled" machine wears of quickly after the numerous time you will need to take this machine ... Hoover Vacuums

Last night as I was vacuuming, I noticed that the belt stop indicator light was on. I pulled out the hair that had gotten tangled around the brush in hopes of solving the problem. It didn't change things. I then unscrewed the entire bottom piece to take out the brush roller. I removed hair from the end piece of the brush roller and reattached the belt; however, I cannot figure out where the microchip is supposed to go so that I can reassemble the base piece by screwing it back together. It seems


Not sure what you mean when you refer to a "microchip" but maybe it is a sensor that works with the belt.\015\012Anyway, if you Google the make and model number of your vacuum you can probably get an exploded view or owners manual that might indicate ... Vacuums

My 4870 K Boss is 2 years old. I have replaced belts & filters in the specified intervals. This last time I replaced the belt after a year, it shredded 3 of them on the outside edge of the belt in about 5 minutes of use. I ordered a new brush roller & heavy duty belt which I installed. It began shredding the belt in less than 5 minutes of use. What is your suggestion? Is this a known problem with this model? Eureka says no and is not standing behind it.


The only reason why it would be shredding the belt is if the pulleys were not lined up correctly. Check the allignement of the belt to make sure there is nothing kepping the pulleys from being in line. The other thing that it could be is if the rolle ... Vacuums

I have a Bissell Pro Heat 2X carpet cleaner and the brushes spin, then stop. I turn it off and when I re-start, the brushes do not spin until I push foreward. The it spins and stops again. Both belts are tight. The brushes spin if held above the carpet, but upon contact with carpet it stops. Same thing on a hard surface.


The reason for the brushes to stop when it is above any surface is there is a switch in the handle that stops the brushes so it dont burn your motor up it may have a faulty switch. ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

The belt burnt out and it seems as though the red arrown does not release the belt. Like it is backwards from the green arrow. It had a burning smell and the belt broke. Then the second belt started to burn out when the brush roller wasn't spinning. Not sure what might be wrong. Green light will not come on either.


It sounds as if there may be a piece of the broken belt in there. Look carefully with a flash light and remove any remnants you find, using a pair of pliers if you have to.\015\012\015\012Also, remove the entire brush roller assembly and ... Kirby Ultimate G Bagged Upright Vacuum

I replaced my Bissell vacuum cleaner belt with a Bissell belt. I ordered it from them so I know it's the right one. I replaced it and the roller won't spin and the belt smells like it burning.


Beckiande485: You will need to unplug the vacuum from the wall, lay it down so you can see the bottom of the vacuum head and remove the bottom plate (foot plate) Probably philllips head screws. pull up on the roller (called the beater bar). ... Bissell Vacuums

Beater Bar The "Beater Bar" or roller with brushes on it, is not spinning, therefore not picking up. I cannot locate my manual and need to know if it is belt driven and how to get at the belt to identify the size and purchase and install a new belt. Thank you for any assistance. [email protected]


Take off the bottom plate, then you can get to the brush roll and belt, on the model number plate, the number of the belt is on that, it is also on the belt if you can still make it out. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Brush Roller Wondering if I need a new brush as well as a belt. The Roller seems to have trouble spinning when it makes contact with the carpet no matter how the height is set. Everything else seems to work fine. Do I need a new roller to fix this problem?


The bearings can go bad in the brushroll. It may need replaced, even if the brushes aren't worn. Helpful link....\015\012\015\012 ... Kirby G6 Bagged Upright Vacuum

My floor brush stopped spinning, I cleaned everything out as per your directions in other posts and following the instructions in the manual. Now the floor brush wobbles and has a hard time spinning when upright. Looking at the end of the brush, opposite the drive belt, the bearing-type end that the brush spins on appears to be off-centered. Is there an easy way to fix this???


... Bissell 3130 Bagless Upright Vacuum

Changeing belt how do you install a new belt? I have an Eureka, The Boss, bagless, upright. The brush is hardly rotating. I think it could be the belt but i cannot open the vacumm to check it. How can I fix this?


... Vacuums

I have an old Progressive vacuum cleaner that says "Hepa Filter" and "Whisper Belt". Not sure what the model # is. The problem is that the vacuum part itself (the part that touches the floor and rolls over) has ejected its filter that we can see through the little window- it just came out under the rollers under the device... we cannot see how to re-insert this piece of filter which looks like a kind of round, flat grey foam/fabric and clearly goes inside- (top of the part that touches the flo


Check this procedure:\015\012\015\012Unplug the appliance that you will be \015\012changing the filter in.\015\012\011\011\011\011\011\011\011\015\012\015\012\011\011\011\011\011\011\011\011\015\ ... Kenmore 23313 Whispertone Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1035 seconds