Having problems with your Hoover U6630-900 WindTunnel Bagless Upright Vacuum ?

My Hoover Wind Tunnel has no suction, unless I use the hose and wands. It is less than a year old. Where do I take it to get repaired?

Answers :

Before you take it anywhere, please check the following:\015\012
\015\0121- Make sure the belt that runs the beater brush on the bottom has not broken.\015\0122- Be sure the beater brush has not frozen up due to debris. You should be able to move it by hand.\015\012Best to remove the brush, clean all debris as best you can and add some WD40 to the rubber pieces at each end of the brush. Turn the rubber pieces to work the WD40 into axle at the end of the brush until they move easy and reassemble.\015\012
\015\012If you find this information to be of help, please go to the rating section of FixYa and provide me a rating.\015\012
Repair Help & Product Troubleshooting for Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Hoover Wind Tunnel has no suction, unless I use the hose and wands. It is less than a year old. Where do I take it to get repaired?

Before you take it anywhere, please check the following:\015\012\015\0121- Make sure the belt that runs the beater brush on the bottom has not broken.\015\0122- Be sure the beater brush has not frozen up due to debris. You should be able to mo ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Have a 3 year old Pfaff Creative Vision. Has less than 14 total sewing hours on it. Has had issues in the past. Breaking needles, wouldn't stitch out designs in acceptable manner(badly distorted looking) breaking needles repeated, now it is changes stitches on its own, then went to sewing the same stitch but isn't sewing it consistantly. I have taken it back to the same professional to repair each time. Can thhis machine be repaired??? Should I trade it off and get another, this isn't my first c

It sounds like this machine has some kind of fault in it for sure. It can be repaired again, but will likely need to be repaired again after that - down the road. Personally I recommend you just get rid of this unit and go for a different model. Y ... Vacuums

Hoover tempo upright is clogged. I can only vac for a few minutes, then I have to unplug it and turn it over and clean out the under part under the roller. It is totally stuffed with dirt and dust and carpet fibers. I have a new bag in. It is like it is clogged up inbetween the bag and the roller. Also gets clogged when using the hose. It is maybe a year old. How can I take it apart and unclog it?

Disconnect the hose and head and wands. Drop a quarter thru the hose, the handle sometimes clogs. peer thru the wands and inspect the elbow on the head for blockage as well ... Vacuums

Hi, I have a Sebo X4 which is almost 3 years old. I haven't had any problems with it until the last couple of days when I notice a slight screeching noise when in upright position, coming from the roller mechanism area. If I slightly push the sebo forwards it gets worse, if I tip it back it stops. If I take the roller out and switch on, there is no noise. I have always been careful not to tip the machine forwards when using the hose, but I recently lent it to a friend whose hoover had broken do

I dismantled the top part of the machine from the bottom and there stuck right down in the bowels of the tubes was a piece of card, a dress label! somehow it was only making a noise when the machine was in an upright position. It took a bit of stretc ... Sebo X4 Bagged Upright Vacuum

Morphy Richards Pets vacuum cleaner, less than one year old. Not sucking, overheating, claims bag is full when it is new. I have looked for blockages but the hose is clear. Can't find anywhere in Aberdeen to repair it

Discovered I had a 3 year warranty on it so got a replacement. Thanks for your helpful advice! ;) ... Morphy Richards Vacuums

Very little suction on my dyson dc24 yellow ball upright . only 21/2 years old.. should i take it to a vacumn repair shop ? it has a 5 year repair guarantee. I cannot find the papers. But i know that i filled out the guarantee & miled it in. what should i do?????

I'd look at this:\015\012\015\012http://www.fixya.com/support/t2827418-very_little_suction_in_hose_no_tears_in ... Dyson Ball DC24 Bagless Upright Vacuum

Hello, I have the same model. And though it is three years old, starting from the last month, it does not clean anything anymore. Cannot even pick up one single thing from the floor. Every dirt gets stuck in the hose. I cleaned the hose and cleaned the filters but it still does not pick anything up. Is three years its normal lifetime or do I have the change the filters, instead of cleaning them? Thanks.

I know bissell vacuums are very cheap but they should last more than 3 years. there should be two parts to the dirt cup. remove the dirt cup and above it there should be a round plastic part. unscrew it and check that filter. ... Bissell 6594 PowerForce Bagless Upright Vacuum

Shopvac 90L400 quit working (4 years old). Thought the switch was bad but not the problem. I read that there is a fuse link in the motor that frequently burns up. I tried to take motor apart but not sure of the process. I was able to get to the motor but cannot pull it out of the armature. It appears I have to take the aluminum blower unit off the shaft (it appears to be pressed on with a retaining washer). Do I have to take it off to pull the shaft and motor assembly out? Is that where the fuse

By pass the switch and take power right to the motor leads.. that should tell you if the motor is ok.. have not seen fuse link on a vac motor.. graingers has new motors, but not inexpensive ... Vacuums

The motor just went out on my 2 year old vacuum with light usage (hardwood floors in a very small house.) The Sears repairpeople are estimating ~ $130 to fix (this includes parts & labor). I'm wondering if it's worth investing $130 into something i've spent $350 on only 2 years ago. Shouldn't these machines last longer ? Is there something I could do to get them repair free as it seems the motor must have been faulty to only have lasted 2 years. Thoughts ?

Aye, get a dyson, if its out of warranty there's not much u can do bout it :( ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Dear Sir/Madam, My old faithful Hamilton Beach Mixer, now 60 years old, is still working but recently I was told by someone who looked at the motor that it needed repair or replacement. Is it still possible to get it in working condition?

If the armature shaft is worn there might be a problem, but that would be about the only one, Bushes/bearings can be replaced as can brushes. If the armature shaft is worn, a fix can be formulated but it will require some ... Vacuums

I have a Harmony vacuum that's a couple years old. I recently sucked a fair amount of dog hair into it and was unaware something was amiss since the things so quiet. It just shut down and wouldn't come back on. 10 minutes or so later it came back on but now it's got no sucking power. I figure I torched the motor. Good guess? What are my options--I'm out in the middle of no where but can get it to a repair shop 250 miles away. Is it worth trying to salvage or am I going to pay as much to get it f

I cleaned the whole thing out, changed out all the filters again and cleaned out the motor compartment. Then I discovered a huge clog in the line. Once I got that all done--it's now working like a charm. Moral of the story: spend more time looking fo ... Electrolux Vacuums

I have a 3 or 4 year old Hoover steam carpet cleaner: model # F 5857-900  It stopped working and does not vacuum up liquids or dispense liquids for the water container. Where can I take it for repair? I live in Colchester,CT 06415. Also,is there any written repair manual that my husband might be able to use?

... Vacuums

Hello, I have a Hoover 3200 Turbo Power vaccum. while the motor appears to be working fine the vaccum no longer picks up the dirt. I turned the vaccum upside down and the belt appears to be broken. would a broken belt stop the pick up, there appears to be no suction. This vaccum is approximately 10 years old. is it worth fixing? I live in Virginia Beach Va, where would I take the vaccum for repair? my zip code is 23456- Thanks Cleta Goode

... Hoover Vacuums

While using, steam stopped coming out in force at the port levels in the head. Suddenly started high pitch whining, pressed button just above connection site and end flew off with great force pouring water onto floor and carpet. Unplugged immediately for safety and unable to get it to deliver steam force again. Less than one year old and used only 8-10 times only in walk areas where there is no carpet with distilled water. Please, advise, cannot find booklet. Thanks So Much, Beverly Crumme

Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it may not be getting steam to the head...Euro ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

My DC17 is only a few months old, but I've already had to clean the filter. Since I reassembled everything, I'm finding chunks of carpet fiber and dog fur on top of the filter inside the filter container. Iam getting slightly less suction from the floor assembly as well. I've checked the hoses, brush, and brushed out the inside of the plastic container, but hasn't helped. Ideas??

Everyone needs to own an air compressor,\015\012if you own a bagless vacuum\015\012\015\012You blow it out every other time you use it.\015\012\015\012Without compressed air, all vacuums will just\015\012basically ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My 88 year old mother bought a Dirt Devel DHC001 - has been used twice but it looks blocked and has no suction but there is suction at the pipe end if I take it off. I have opened the red end and emptied out but there seems to be dust in the rear part and I have no idea how to get it out. The shop she bought it off thought they were being helpful and removed all packaging but seem to have taken instructions as well.

To answer this properly, I am going to need the actual model number on the bottom of the unit on the silver/metallic sticker. Usually MO###### If you can get that I can help you out further. \012Mark ... Vacuums

Bissell proheat 2x model 8920 water is not spraying out just getting a little trickle. Model is less than a year old

... Vacuums

Hello, my Kenmore 27514 canister vacuum only works on the hard floor...the carpet suction stopped working while I was using it. Is there anything I can do to fix it or is it necessary to take it in for repair? The vacuum is only 1.5 years old. Thanks. Susan 702.340.8015

You need to replace the belt that drives the beater bar. You can do this yourself very easily. If you need help, let me knowJim ... Kenmore 27514 Bagged Canister Vacuum

I have an Electrolux LITE upright carpet cleaner - about 15 years old. Suddenly last night when using it, from the normal motor (whooshing) sound, the motor suddenly went very slow and with a slight grinding sound. The brushes are now just turning round very slowly and areobviously not picking up anything. Has the motor gone or is this repairable, or should I just get a new cleaner? I have tried to open the machine from the bottom to see if anything is obviously wrong, but it looks complicated a

... Electrolux Vacuums

Folks, My wife and I own a three-year-old Hoover U6434-900 self-propelled "Wind Tunnel" upright vacuum cleaner. The problem is that, even on the highest setting (front-end as high as possible), it gets bogged-down in even shallow pile carpet to the point that the brush stops. I've cleaned the machine thoroughly, pulling hair, thread, dental floss and such from the brush (and everywhere else), including unscrewing the brush end caps and pulling out the cat hair mats which formed in there.

Check to see if the V belt sits too deep in the brushroll groove, if it sits too deep you will need to replace the brushroll. the top of the belt should be about flush with the brushroll. also you have to take the screws out of the self propelled uni ... Vacuums

No Suction My two year old Kenmore Progressive stopped working in January. The guy at the Sears service center convinced me that buying a new one would be cheaper than getting it fixed. So I bought the exact same model and now this one has given out in the exact same way! I'm so confused. When I press on, it lights up and makes the whirring noise. Everything seems to be working but there is no suction anywhere. Not in the main part or the hose and there's no "cyclone effect" in the chamber. All

Try looking within the vacuum to see where the suction is getting stuck at. You may have to do some disasselbmeing but this is a manufacturers problem. You should also try to speak to the manager at the support and make a big dispute until you get yo ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Kirby My Kirby is less than a year old.  It's suction is no longer strong. I tried cleaning the hose and even replacing the bag.  Do you have any other suggestions.  By the way, I have the Sentera model.  Thank You

Here is a link to my online troubleshooting guide. Hope it helps...\015\012\015\012http://r ... Kirby Generation 3 Bagged Upright Vacuum

I have a whirlpool personal valet steamer system that is mounted to the wall. The system was in the house when I purchased it so I would suspect it's about 8 - 10 years old and I cannot find the manual for it. When I push the start button it automaitcally cancels the set up and will not run. I have unplugged it for a while and then put it back in and it's worked before but not anly longer. How do i get a manual or can I find a repair person to look at it.

... Vacuums

Shark steam mop. Will not steam but it will get hot.. So disappointed , I have 2 of them & they both have stopped steaming. Less than 2 years old. It just really frustrating.

... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Kenmore Model 116 28014700 intuition vacuum cleaner. Latch for hose connection to cannister broke. I have the new part. How do I remove the hose from the broken part and replace it on the new part? I have already purchaed the new part p/n KC92PDDUZV06 for this, bt can't figure out how to get the old part off. It looks like you must destroy old part in order to get it off.

... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0703 seconds