Having problems with your Hoover U6630-900 WindTunnel Bagless Upright Vacuum ?

Hoover windtunnel motor is running rough and overheating, even after clearing the hoses and removing the belts. Could there be something jammed in the blower? How do I get in there to clean it out?


Answers :

Repair Help & Product Troubleshooting for Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover windtunnel motor is running rough and overheating, even after clearing the hoses and removing the belts. Could there be something jammed in the blower? How do I get in there to clean it out?


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have a Napoleon Pellet stove insert Model NPI40. When the fire burn rate is extremely low it seems to operate normally. However, when I turn the heat up even a little I eventually get a high pitched noise that seems to be coming from the convection blower. Changing the speed of the blower has no effect on the noise level. I cleaned the blower but did not remove it. There was very little dust on it. Cleaning had no effect on the volum or pitch of the noise.


My theory is based upon 1st hand knowledge with a newer EPA compliant freestanding wood burner, with the air-tight and high efficiency ratings.its possible that its just the high rate of air moving through the air chambers , similar to a o ... Kenmore Whispertone 23312 Bagged Canister Vacuum

I have a Bissell 3920 and the beater bar only turns when I'm pulling the vacuum.How do you get the end caps off of the beater bar to clean it out? This has happened before when it was under warranty and I was told to remove caps and clean frequently.I am afraid prying them off will break the vacuum.It also has very low suction and I have cleaned the filters and the belt is fine.Will cleaning the inside of the beater bar fix my problem?


... Bissell 3920 Cyclonic Pet Hair Eraser Vacuum

Hello i own the bissle proheat steamer it turns on but no water or soap or suction from floor or the utensiles ive taken the take off the back to scope out anything that could be in the way but dont see anything the motor is making that clogged vacume noise witch makes me believe something could be stuck somewhere in it but it could also be no water is getting to the pump or despencer but the brissels still work belt for that is good where would i be best to check and where is the location of th


... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help


The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Motor is sparking and smells like burning rubber. When it first happened I thought the vacuum had something jamming the beater bar. That was the smell it had, like when the belt gets burned. But when we turned it over, it wasn't jamming. Took off the base plate and turned it on. The motor area is sparking and it makes a weird noise (I assume that is because the motor fails and restarts). I looked for loose wires, can't find any. I believe I need some sort of part replaced, maybe even a n


From sound and description most possible is motor is burnt up sparks usually mean metal on metal either bearing or bushings went on motor if u can jiggle the shaft thats bearing if u rotate the shaft by hand and feel and or hear rough grinding the br ... Oreck Vacuums

RE: DYSON DC07. Cleaning the roller I removed one end and cleaned it. Cannot get the roller back on the vaccum. If you could give me instructions on how to do this I would be very appreciated. Thank You


Try this link. http://www.sparesaver.com/help-and-suppor ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

In my (almost new) Dyson DC31 Animal the rolling brush tends to stop like the bearing was kind of difficult to turn. I opened the side carter and removed the little belt. Without the belt the engine runs regularly. I cleaned the little knots of hairs trapped in the bearing but still the brush runs for a while then stops, tries for a bit then stops again. I even tryed putting a bit of synthetic lubricant with apparently no result. Could it be a defective bearing? Thanks for your help.


... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

Dyson DC 14 hose has no suction, with or without brush attachments. Hot air shoots out from the base of the canister when I try to use the hose. I cleaned the top filter, but can't figure out how to remove the hepa filter to clean it without destroying the case. It looks like it might take three hands to insert pennies and "flip" the case open as is suggested on a youtube video for a different model. Would this even help, assuming I could get the thing open?


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Our vacuum model #6579-3 spits dirt and everything out the front and when trying to use the attachments we have cleaned and washed every removable part of the vacuum is there something else we could to fix it or is it permanently damaged??


... Bissell 6594 PowerForce Bagless Upright Vacuum

Bissell powerforce My lower pickup tube became clogged so I removed it and cleaned it out and reinstalled it.Now everything runs good but the vaccum want pick up any dirt .I replaced the bag andf when I turn it on it just exhaust air but does not have any suction,I tired tp pull the bag door of while it was running whick I could not do so it has plenty of suction inside just not getting any outside can you help?


... Bissell Vacuums

It starting to put out a hot type smell. I have tried cleaning the filters real well and even tried to see if there was problem with the ozone filter. We have checked and could not find a jam. I know the hose has excellent suction. The vacumn works but the intelliclean sensors will not. It only takes about 15 seconds or so for the odor to start. Then it gets real strong and it makes my eyes water


Hi,The hot smell could be from the belt or the motor. Turn it on for a moment, turn it off, then flip it on its side and smell the belt that drives the brush. If that is where the smell is coming from, then your belt is burning up. ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

One day I was vacuuming and it sounded like something went up inside somewhere and the motor, I assume,..... is frozen ..all it does is hum when I turn it on! I have changed the belt, filter and checked and cleaned all hoses... what could this be? THANK YOU, Gail


It's likely something got into the fan, is stuck there, is preventing the fan from turning, and so prevents the motor running. There's a good possibility the motor burned out because of this. If there's a strong smell of burning metal, this is prob ... Hoover Elite Rewind Bagless Upright VacuumVacuum

I have a DC 15 Dyson Ball Vacuum. I've removed and cleaned the filter. I can't get the lid to close properly. I don't want to force it and break something. There is some kind of a red spring loaded tab that seems to be in the way. How do I reseal the top of the vacuum?


The red tab doesn't let the lid close if the filter is not fitted correctly or the wrong filter is fitted. Many after-market filters cause this problem. \015\012\015\012Have you recently fitted a new after-market filter? ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

When I turn on my Kenmore Premier 4.5 Peak HP 10.0 Amp after about a minute of running I get a burning smell. When I opened up the compartment that holds the dust collection bag, and remove the bag I found a filter. The filter was minimally dusty and has been cleaned. After sniffing around, I could not identify the source of the smell.


Dose it smell like rubber check your belt ... Vacuums

Dyson dc14 How do we replace the belt one I removed it to clean hair from brushes? Can't get it back in place. Any tricks or suggestions. Craig Dittmar


Hi am i right to assume the belt is still in place ie in position around the drive wheel of motor? and you have removed the roller/brush only? and you now have difficulty re assembling the belt on brush and relocating brush into its holder ?? ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

HI I have a Bissell Pet Hair Eraser it has a very loud high pitched squeal, I have removed the belt & cleaned it with no effect. Is there something else I cn do? Thanks Joe


The belt may be stretched out and therefore, no good. You can try roughing up the surfaces the belt rides in with some 150 grit sandpaper. That may do the trick ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

Water wont come out when handle pressed to do floor or out of nozzle for upholstery cleaning smells hot when trying to get it to work could this be a belt


Yes it most likely is the belt ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Roller Brush How do I install the roller brush. I didn't pay attention when I removed it and now when I attempt to vacuum my low carpet it doesn't seem to be working. The green light on the head of the vacuum goes out when I click it down to the floor. It didn't used to do that. Plus I think I smell something burning. Could the belt be broken?


Try a new belt. The ends of the brushroller are different sizes, so you can't put it in backwards. There are numbers and notches on the ends of the brushroll. These notches/numbers need to match on both sides when installing it. (probably need b ... Kirby Ultimate G Bagged Upright Vacuum

I have a Sanitaire model SC886 upright vacuum. It's about a year old. I replaced the belt , cleaned bag , checked for blockage in impeller fan and now it makes a noise , like a grinding noise or something . Could you tell me how to fix it ?


The bearings in the motor needs to be checked,or the impeller is damage. ... Eureka SC886 Bagged Upright Vacuum

Cleaned the brush but could not get the central belt to hook back on by following manual directions


FLIP THE BRUSH (RUG RENOVATOR) OVER AND REMOVE THE SCREWS ON THE SILVER GUARD THAT KEEPS THE ROLLER IN PLACE. SLIDE THE ROLLER UP OUT OF THE SLOT, TAKING NOTE ON THE HALF MOON SHAPED SIDE. REMOVE THE OLD BELT(OR WHAT'S LEFT OF IT). PLACE THE BELT ARO ... Kirby Heritage II Vacuum

Hoover Mach 6 U5198-900 vacuum roller brush won't turn. I had opened the bottom to clean hair off the roller. the belts are not broken. When I closed it and turned it on, now the roller brush won't turn. I can push and turn it by hand, but not easily. Then I noticed the brush on/off switch is turned off, but when I step on it, it won't turn on. I was thinking I let something get out of place when I opened the bottom, but can't see what.


... Hoover Tempo Widepath Upright Vacuum - Blue

I bought this second hand, so have no manual for parts, etc. I smelled something really bad, am assuming it was the belt. How do i release the head of the vaccume to get to the roller. It needs cleaned anyhow.


Rotate the front belt lifter from green to red then rotate the locking knob above the nozzle. and the head will lift off. it helps if you put the height adjustment in the highest setting. did it smell like rubber burning? ... Kirby G5 Bagged Upright Vacuum

My Dyson vacuum works fine for cleaning the rug but the hose doesnt get any suction at all. I removed the hose and all the parts around it that I could and dont see any clogs or broken pieces. I lost my manual so I dont know if this is addressed, or if there is a switch Im not flipping. Gave it a thorough look but found nothing.


Hi there,Sorry to hear you're having a problem with your DC07. If you have suction through the cleaner head but not through the wand, it sounds as though you have a blockage. Although you say you've already checked for these, you may find ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have an older Oreck XL that has worked great. The belt recently broke and I reinstalled a new one but now there's a rattling noise like something is loose and a burning smell. I've cleaned it as well as I could but still nothing. Help please!


When you turn it on, is the brush roll spinning? (Check carefully, as lifting the unit from the floor exposes a brushroll that should be spinning at a high RPM.)\015\012\015\012Did you get the brush roll properly seated in the slots? Does ... Oreck XL Ultra Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0894 seconds