Having problems with your Hoover U6630-900 WindTunnel Bagless Upright Vacuum ?

After running for 15 minutes, the windtunnel vacuum cleaner shuts off. It will not restart until it has been off for 30 minutes. Could it be overheating for some reason. All of the filters are clean; the dust tank is empty; the belts have no cracks.


Answers :

It's not necessarily overheating, but the thermal-fuse is definitely tripping and it takes 30 minutes to reset. There are several causes of this (in most common order):
\015\012
\015\0121. A blockage in the suction system or a full dust tank
\015\0122. Dirty filters (Don't forget to check the air outflow filter at the back)
\015\0123. A worn belt
\015\0124. A faulty thermal fuse.
\015\0125. A faulty motor
\015\012
\015\012As you've stated that the dust tank is empty and the filters are clean (don't forget to check the HEPA / air outflow filter at the rear), let's look at the other options.
\015\012
\015\012Check the suction is good by putting your hand over the end of the hose and seeing if it will stay attached to you hand upside down.
\015\012
\015\012Next, check the belt isn't slipping. Lie the hoover on it's side and check the rollers are turning constantly and at high speed. This isn't foolproof as it doesn't account for the extra friction of the brushes on the carpet, but it's a reasonable test. A worn belt wont necessarily be cracked. It can stretch and slip without cracking. Also, when a belt is slipping, you can usually smell burning rubber.
\015\012
\015\012If the hoover runs ok for 15 minutes and there is no burning smell from the motor, then it's more likely a faulty thermal fuse than the motor itself. They are replaceable but unfortunately, thermal fuses aren't always sold separately and sometimes you have to buy a new motor (!!) to get a new fuse. Hoover are one of the best manufacturers when it comes to buying spares, so you might be in luck.
\015\012
\015\012I've removed faulty thermal fuses from vacuums because a spare wasn't available without buying a motor. However, I have always done this with the owners full consent after explaining to them that a safety feature has been removed and they should avoid using the vacuum for prolonged periods without letting it cool. I also test the rest of the vacuum fully before returning it.
\015\012
\015\012If you want to try removing yours, it will be attached to the motor with simple spade connections, but you do this AT YOUR OWN RISK. The danger in doing this is that the motor will burn out if it gets too hot, rather than being switched off by the fuse.
Repair Help & Product Troubleshooting for Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

After running for 15 minutes, the windtunnel vacuum cleaner shuts off. It will not restart until it has been off for 30 minutes. Could it be overheating for some reason. All of the filters are clean; the dust tank is empty; the belts have no cracks.


It's not necessarily overheating, but the thermal-fuse is definitely tripping and it takes 30 minutes to reset. There are several causes of this (in most common order):\015\012\015\0121. A blockage in the suction system or a full dust tan ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

New morphy richards vacuum overheating. cleaned filters, replaced belt but still overheating


... Vacuums

My Hoover wind tunnel keeps overheating and the red I dictator is on. I have cleaned all filters and checked for clogs....could the motor have dust in it? How do I check?


Okay. I read these posts and decided to take the advice of checking the hose.I had cleaned all filters, checked all hose (as-is) and did belt checks, etc.The indicator was always showing red and it would shut down after about 5 minutes. ... Hoover UH70120 WindTunnel TSeries Rewind Bagless Upright Vacuum Cleaner

Vacuum cleaner LG model V-UP142NJP THE CLEANER OVERHEATS EASILY AND SHUTS OFF. WE CLEANED ALL DUST FROM FILTERS, CONTAINER ETC. WHAT ELSE CAN WE DO? SHOULD WE CHANGE BELT? [email protected]


... LG Vacuums

How to disassemble the brush to empty anything that might be stuck inside of the brush? The motor seems to be overheating, all belts have been checked, all airways are clear and the filter is clean. The vacuum is vibrating and releasing a burning smell, but still sucking up dirt. There is nothing stuck on the outside of the brush, but is there a way to check inside of it to see if that is where a clog is occuring?


If there's a burning smell and the belts are fine, the problem is going to be hot wires causing the insulation to melt, or the motor going bad. Discontinue use and have it checked at a repair shop. ... Bissell 6594 PowerForce Bagless Upright Vacuum

I own a Miele S5210 vacuum cleaner which has stopped working. It looks like the dust bag wasn't fitted properly and the machine is very dirty and the filters are completely clogged. I've cleaned it up as best I can and have replaced the filters but it still won't operate. How can I get inside the casing to clean the inner motor compartment? Thanks Tom


... Vacuums

The removable filter at the front is cleaned regularly, and is not clogged. However, the machine appears to be suffering from being clogged by dust, as it has started to make a high pitched noise, and I fear it may burn out. I can see some dust inside the front panel but cannot see how to remove the front to clean it out. (NB. I have located two screws - one on either side - but cannot see how to proceed further.) Please help! Thank you.


\015\012\015\012Hi,Here\015\012is a tip that I wrote about my Bissel but I bet you have the same\015\012problem and the hose is clogged...Bissell Bagless Upright\015\012 ... Vacuums

I have a Miele Vacuum cleaner MedicAir 5000 Plus. Recently the Dust Bag Indicator bar is full during normal cleaning and consequently the suction power is much less. I replaced the dust bag, engine pre-filter and Hepa filter but no change. When i remove the hose, the Indicator is normal, but when i attach the hose, wand, head, the indicator is full. I checked the hose, wand, head but can't see any blockage and when i blow with my mouth it seems fine. Can anybody help? thanks!


... Miele Vacuums

Unbeknownst to me, someone took the bag out of my Kenmore Progressive vacuum and failed to replace it. I have been vacuuming without a bag for months, and today the vacuum stopped sucking. When I opened up the front to replace the bag, tons of dirt and dust came pouring out. I thoroughly cleaned the vacuum, put in a new bag, but still no sucking power. Just dust coming from the rear vents where one of the filters is. Is the vacuum ruined, or is it a simple solution of buying a new filter?


Sounds like you need to buy a new motor. All that grit and dust will ruin a motor and I'm surprised it lasted as long as it did.\015\012This is where a vacuum that won't run without a bag would have been nice. (Aerus for one) ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

I have a Neotec XJ-2000 ionic air purifier. On the bottom of the device, it says I should open the casing and take out and clean the dust filter every month. I haven't done it in years and no longer have the manual. How do I open it up to get the dust filter out?


... Vacuums

Hi, I have a sanyo SC164R/185R vacuum cleaner and just wanted to know if it has a HEPA filter? I can't find any info on this; the instruction manual just talks about cleaning the filter but doesn't specify what the filter is. I have a child that has just been diagnosed with a dust mite allergy and apparently a HEPA filter is what we need to help iliminate them.


... Sanyo Vacuums

I have a Bissell 3920 and the beater bar only turns when I'm pulling the vacuum.How do you get the end caps off of the beater bar to clean it out? This has happened before when it was under warranty and I was told to remove caps and clean frequently.I am afraid prying them off will break the vacuum.It also has very low suction and I have cleaned the filters and the belt is fine.Will cleaning the inside of the beater bar fix my problem?


... Bissell 3920 Cyclonic Pet Hair Eraser Vacuum

OUR DYSON 07 SWEEPER HAS VERY LITTLE Vacuum, have cleaned all filters and hoses, on line troubleshooting has said to check soleplate being on correctly, we have done this, still does not have good vacuum, belts are covered by a housing, the video that shows the changing of the belt is not the same, I need to know how to remove the cover to check both belts and any help in gaining the vacuum


This video shows you everything you need to know ... Vacuums

Have ultra vision and have changed filter and foam filter, checked all hoses but still will not pick up. Belt is fine and brush is clean and spinning properly. dirt stays at top of filter instead of falling into canister.


My kids get mine stuck all the time :(Take the vacuum outside then:Remove the hose at the bottom and see if there is any obstructions. Also shake the hose to make sure there is nothing in there as well or take it out side and make s ... Dirt Devil Vacuums

Noise Hi... I was doing normal house work and had been using it on carpet... I put it on floor for my hardwood floors and picked up loose clean cat litter and went to put it back on carpet and it made a horrible noise like it was rubbing. cleaned the filter... cleaned the roller thingi ...checked the belt and it is still making that horrible noise. It does not make the noise when I have it on floor but as soon as I put it on carpet it screams at me. Help! Please and thanks Linda


Hi Linda,\015\012Sounds like clutch problems, try to move the lever for carpet/floor back and forth a few times maybe it will free up. If it still makes the grinding noise, the clutch assembly will have to be replaced. Let me know, i can even ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hi, There is a high pitched whirring sound coming from lower part of the vacuum. When I tilt it toward me (while standing in the normal vacuuming stance) the sound sometimes lessens for a minute or so. I have tried the following things: -cleaned the two sponge filters -emptied the dirt receptacle -removed the roller and cleaned it -cleaned the brushes -the belt is not ragged and does not seem floppy -checked all of the airways for clogs (including removing the wheel base) Can you help?


Your looking for some dirt stuck in some thing you didn't check yet. with the roller out and the belt out of the way run it to see if it still makes the noise. if it does then you looking at the impeller or the motor bearing themselfs those bearin ... Bissell 3750 Lift Off Bagless Upright Vacuum

Roomba is not picking up dirt but does pick up dust. That is, the dust chamber has dust in it but the dirt chamber is empty. The brushes don't have any fluff on them either which is not normal. The fan is blowing out plenty of air, the filter has been cleaned but we suspect the brushes aren't turning. an you help?


... Roomba Vacuums

DC25 Overheating after a filter cleaning


You need to not use this until you get it fixed at a vacuum store.they can probably help you with it.might be there is a short or a little water got on the motor. ... Dyson DC25 Vacuum

Why does my dyson slim dc18 keep shutting down, even though i keep it clean. Filters area is clean and all others have been properly blown out with air from a air compressor. It will work for about 5-10 minutes and then shuts down. Smells like ****, check the belt and a bit later it restarts again. It's seems to be almost over heating.


Maybe your motor is going. Here's a link to a site that talks about motor failure and replacement in a DC07 (not DC18). I don't know exactly what the odor smells like but maybe you can see if you have any of the other symptoms. Good luck! ... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow

Roomba 550 dust bin always empty but filter and brushes always need cleaning. doesn't seem to clean as well as in the beginning


I just got off the phone with tech support. They think the brushes are not rotating properly, or intermittently, and will send a replacement part. I doubt this is the issue sinde I can see them spinning. Next step is a replacement. ... iRobot Roomba 550 Vacuum

Bag was not on good, resulted in dust,dirt, dog hair everywhere...have cleaned pretty thoroughly but vacuum does not have any suction. After taking apart did find that the larger wide belt is broke but I think that just affects the self propel...is there a belt tied to suction? HELP!


Greetings from GoVacuum,\015\012\015\012There are two things that you should check on this vacuum after running it without a bag inside. The first thing you should check is the filter that is underneath of the vacuum bag. This filter i ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Overheating Hoover My Hoover cyclonic 1800w keeps overheating and turning itself off, not sure if it's the filter, I've cleaned it but it didn't look very dirty.


Most likely caused by a lack of airflow. Check to see if you have airflow at the end of the hose. If not, Remove all of the hoses and ensure that they are not clogged. If there is airflow through the hose; check the air inlet immediately aft of the b ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

Hoover self-propelled windtunnel U6430-900 flat belt gets hot & becomes hard to push. It has a filter bag. Purchased 8/2/01. Took one plate off bottom. Used a compressor to blow out dirt & dust. Put new thin belt on.


Belts get hot when fibers from carpet get wound arounf the belts mounting shaft. Best to take a razor and cut off any fibers so the belt doesn't get hot again ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

I have a Eureka Altima vaccuum and it no longer suctions like it use to and also has a burning smell. I have cleaned all filters, brush, hoses, and filters. There are no blockages. I have also checked the belt and it's still good. Any other ideas as to what may be the problem?


This bagless model gets buildup of really fine dirt in the motor and starts to clog up the fan airducts. You will need to take the motor out and clean it. ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

My Kenmore Progressive keeps burning up belts even after I have changed the bag, cleaned the filters and checked to make sure the agitator was clean and free turning


On the left hand side, just above the handle release, is a lever to adjust if you are doing hard wood or carpet cleaning. When adjusted for hard wood, that lever releases the belt and just uses the "vacuum" function. When set for carpet it engages ... Kenmore Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0746 seconds