Having problems with your Hoover U6630-900 WindTunnel Bagless Upright Vacuum ?

On several occasions the belt has come off the Hoover Windtunnel beater shaft and had to be re-installed. Is there any way to prevent it from slipping off? The shaft seems to be made so that the middle if it is wider(thicker than either the end or the part closer to the motor, which, to me, is a bad design so I don't know how to overcome this problem. I'd be very grateful for a permanent solution to this problem. Thanks in Advance, mas


Answers :

Your belt is stretched and needs replacement ( # 38528035 ) . The agitator is crowned so that the belt stays centered.
Repair Help & Product Troubleshooting for Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

On several occasions the belt has come off the Hoover Windtunnel beater shaft and had to be re-installed. Is there any way to prevent it from slipping off? The shaft seems to be made so that the middle if it is wider(thicker than either the end or the part closer to the motor, which, to me, is a bad design so I don't know how to overcome this problem. I'd be very grateful for a permanent solution to this problem. Thanks in Advance, mas


Your belt is stretched and needs replacement ( # 38528035 ) . The agitator is crowned so that the belt stays centered. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Bissell proheat 2x 9200 series carpet cleaner. I need to remove the Brush Drive motor. However, this series has the gear end of the motor shaft poking out a hole on the left hand side. I removed the retaining washer and pin from the gear shaft. I need to get the gear off of the shaft in order to remove the motor. It's not budging. How do I remove the gear so I can pull the motor out of the unit? Thanks .


Chap, I wish someone had answered this. I'm having the exact same issue. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a simplicity f3500 and while vacuuming the plastic part of the motor with the blades broke off, (the end plastic part of the motor....where can I buy that part without replacing the entire motor? Jodi


SURBAN VACUUM 315-4543111 ASK FOR KEN ... Simplicity 7850 Premier Bagged Canister Vacuum

I have a Hoover, Steam spin scrub, Model F5897-900. Only used it a couple times and the motor gave out. First started being noisy then a bad smell. It did seem noisier that what I would expect from the start but I didn't realize it was a problem with the shaft of the motor. I took it apart and found the motor shaft wasn't true and causing sparks. The motor looks like it can not be taken apart and repaired. This seems like a default from the beginning but it is past warranty. Also noti


You will have to replace the motor and the hose asm. thehooverstore.com may be able to help, or you should be able to find a repair shop that can order them for you. ... Vacuums

Shopvac 90L400 quit working (4 years old). Thought the switch was bad but not the problem. I read that there is a fuse link in the motor that frequently burns up. I tried to take motor apart but not sure of the process. I was able to get to the motor but cannot pull it out of the armature. It appears I have to take the aluminum blower unit off the shaft (it appears to be pressed on with a retaining washer). Do I have to take it off to pull the shaft and motor assembly out? Is that where the fuse


By pass the switch and take power right to the motor leads.. that should tell you if the motor is ok.. have not seen fuse link on a vac motor.. graingers has new motors, but not inexpensive ... Vacuums

The belt on my used Eureka Boss 5857 upright slips off the end of the motor shaft every time the vacuum is used. When I turn the brush roll slowly by hand, the belt walks toward the end of the shaft. It looks like there was a plastic projection from the base that snapped off, and maybe that plastic piece used to block the belt from falling off. Do I need to try to reconstruct that plastic piece, or is something else wrong?


... Eureka 5856BVZ Boss Bagless Upright Cyclonic Vacuum

Motor has strong burn smell and bad sparking.. Where can I get a motor or motor parts? Who makes this motor?


... Riccar 8650/8625 s Vacuum

The bearing mounted gear/cutter assembly at the bottom of my 6 month old GE 169188 blender has gone bad; it's very loose and leaks fluid. The part is easily replaced. Only problem is that I can't find the part anywhere I've looked online. What is the deal? Why dont they make such a simple part available for a nearly new cheap appliance????


Cannot find that model number.. However.. Contact GE parts and service.. here.. https://www.geapplianceparts.com/GEApplia ... Vacuums

It works well until it bumbs a wall. When it backs up it will not go forward again. I took it apart and noticed a cable is lose. I dont know where this cable hooks up to. One end is on a plastic disc on the end of the motor. The other end looks to have been pulled lose from somewhere. Its only about an inch and half long.


... iRobot Roomba 560 Robotic Vacuum

Missing part on motor shaft?


The reason the belts are burning up so quickly is the old rubber from the other belts is still on the motor shaft.clean the shaft down to the polished finish then put on a new belt.make sure your brush roller turns freely .thats the other possiblity. ... Dirt Devil M086700 Vision Bagless Upright Vacuum

Miele S5000 (revolution 5000) vacuum cleaner - How do I open the casing? When the power button on the handle is pressed the green power-level lights on the handle light, but the motor sounds like it gives a little 'jump' but nothing more. The orange power light on the body also dims. I assume the motor or fan is jammed, but I can't open the body to find out. I've taken out to screws inside near either end of the handle, but to no apparent effect. I'm assuming the body is held together by plastic


... Vacuums

My progressive brush motor only works when I've got it twisted to the right, and then not always. Obviously a bad connection. The female part of the connection at the handle is blackened. Is this something we can repair/replace ourselves, and if so, how? which parts do we need


\012I will give you the easiest way I think you van solve this. What I would do is take the wand down to my local used vacuum store and show them the piece with the black on it. If they agree that it should be ... Kenmore 25512/ 25513 Progressive Canister Vacuum

On my Kenmore whispertone 5.1 the bearings are bad on the motor there are two bearings they are listed as 608 BRS I see bearings all over ebay 6082RS 608SS but none BRS can I use any 608 Bearing or does it have to be a 608 BRS Bearing are these dry bearings or greased bearings I cant get any real information on the bearings I dont want to go to sears when I can get bearing much cheaper off ebay can some one shed some light on the bearings I would use the motor is made by Lamb Ametek went to ther


... Kenmore Vacuums

We have inherited a Filter Queen Majestic Triple Crown Model 99C vaccum and have no owners manual stating the year it was purchased and parts available. Our power hose electic wire connection (about 6 inches long) which plugs into the main unit is split in the hose attachment end. The motor sound went instantly quieter and I wondered if this was why when I found this frayed electical wire. It has not been used since this problem was found. How much is this single replacement part? I live


... Vacuums

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?


Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

How to tell which part of kirby g3 electric motor is bad


Normally its the field wire that goes first, needs visual inspection,\012cant test power switch,so will have to test with new one ... Kirby Generation 3 Bagged Upright Vacuum

The head on my canister vac vibrates, smells and makes a bad sound. When I took it apart the inside of the "end brush tufted" piece had bits of the plastic broken off. Should I replace the Agitator Unit Assy or could this be the motor?


If you are talking about the end cap is broken off the agitator, I would replace the agitator. you can check the motor by turning on the vac without the roller installed. ... Vacuums

My bissell 6590 works fine with hose attachment. Motor shaft turns when belt and roller are off. When belt and roller are on it's noisy and smelly. Now one end of the roller actually melted in the holding slot. Do these rollers wear out like this or should I be looking for another problem.


Replace the roller,belt and before instalation clean motor shaft where belt rolls. you can turn on the vacumm and using a knife scrape the motor shaft from the black dirt. ... Bissell 6590 CleanView Bagless Upright Vacuum

Hi, belt came off ny Electrolux Velocity 2000w upright, got belt back on but have a metal srip that looks like it belongs at the motor end to keep belt on. which way in does this go as plasticlooks bit damaged and dont want to force it in wrong way,


... Electrolux Vacuums

My G6 kirby stopped working. i have checked the wire for fraying and continuity and found no problems. I have noticed that the foot pedal that turns the machine on doesn't seem to click when pushed on or off either. i have the motor exposed now to check if it is bad, but i am not sure how to pursue doing just that.


... Kirby G6 Bagged Upright Vacuum

Cant remove belt no room at end of motor shaft, looks defective


You have to remove the cover. It isn't a defect, it's a way to keep unqualified people from messing with the product. ... Eureka Smartvac 4870 Bagged Upright Vacuum

Th end of the shaft that come from the motor is worn out, and won't hold the belt well. How do I change it?


Hello,\015\012\015\012Thanks for the clarification. I have never seen this problem previously in a Kirby. I wonder if the belt keeps sliding off because it's been stretched out? After about 1-2 years, the belts on the Kirby will str ... Kirby G5 Bagged Upright Vacuum

Bad beater bar end bushing for eureka 5860--part number??


... Eureka 5860A Bagless Upright Cyclonic Vacuum

I have an electrolux genesis upright vacuum that I bought used about 8 years ago. It has been A great vacuum the best I ever had. I thought the belt had come off so I took it in for repair. They called today and said that the brush rotor motor was bad and it would be around 148.00 dollars to repair. My question is could I buy the part and have my husband replace it or would it be too complicated. Can you still buy an electrolux vacuum comparable to this one and how much are they. I love this vac


... Vacuums

Plug Part # 8191782 on my kenmore vacumm wand is bad, I dont know how to get the wand apart to change it


... Kenmore Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0560 seconds