Having problems with your Hoover U8125-900 Savvy Bagged Upright Vacuum ?

Drive and brushes stopped

\015 Savvy U8125-900. when we turned on the vacuum the brushes would not spin. we checked for blockages and there werent any. we waited 30 minutes and still nothing. tried again the next day nothing. the brushes move when I rotate them by hand. Clean bag and plenty of suction. Any ideas?\015

Answers :

Look for a missing belt that may have burned off or broken. Was there a burning smell at some point before the roller quit turning? If so, the belt must be replaced. I would also look at the ends of the roller to see if there is any string, hair, etc. that might be binding the roller that needs to be removed.
Repair Help & Product Troubleshooting for Hoover U8125-900 Savvy Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My floor brush stopped spinning, I cleaned everything out as per your directions in other posts and following the instructions in the manual. Now the floor brush wobbles and has a hard time spinning when upright. Looking at the end of the brush, opposite the drive belt, the bearing-type end that the brush spins on appears to be off-centered. Is there an easy way to fix this???

... Bissell 3130 Bagless Upright Vacuum

Have model 3576-6 Bissell Cleanview II and drive belt keeps slipping off peg that is sticking out from motor pulley causing vacuum to stop working properly and brush to stop moving properly

... Vacuums

Drive and brushes stopped

Look for a missing belt that may have burned off or broken. Was there a burning smell at some point before the roller quit turning? If so, the belt must be replaced. I would also look at the ends of the roller to see if there is any string, hair, e ... Hoover U8125-900 Savvy Bagged Upright Vacuum

I have a Bissell proheat 9200 T. The brushes engage when the handle is lowered. However they only turn for about 20 seconds then stop. If you turn the power off then on they run about 20 seconds again. It is driving me crazy!

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9200 Upright Vacuum

Faithful Sebo X1 upright, about 12 years old, stopped working today. I replaced old with new dust bag, checked all dust paths were clear, checked main brush was clear/clean, and drive spindle rotated OK with fingers. When power switched on, the two red indicators briefly flash on then off, but nothing more happens, motor does not start - even with power reaching machine. Tried removing all consumables, refitting and turning on a few times to reset, no joy. Removed base cover, both belts were i

At 12 years, this vacuum has had a good long life. I suspect the motor is shot, but it could be due to faulty wiring and connections. A bad switch, break in the power cord, and worn brushes in the motor are other causes.\015\012I recommend ta ... Sebo Automatic X1 Bagged Upright Vacuum

I have a kenmore progressive 359235 vacuum with intelliclean. Has been great for about 3 years but now the brush bar has stopped turning. This is a direct drive unit with a circiut breaker reset button on top . The button is not tripped. Any ideas ?

... Kenmore Vacuums

We have a Hoover upright vacuum cleaner, model Core 7. There is a switch that turns on and off the brush drive. This operates via a cam with a bearing putting pressure on the final drive belt to engage the brush head. My brush head is not turning and with the lever set to engage the drive there is still considerable slack in the final drive belt. There appears to be only a bearing deflecting the belt, should there be a pully or other device mounted on this bearing? There is so much slack a

Yes, there should have been a white plastic sprocket on top of the bearing - in its channel the belt would sit. Unfortunately no parts are available for this unit that can be bought retail - only available by order to dealer repair shops.\012\012\012 ... Hoover Vacuums

I have a Bissell Pro Heat 2X carpet cleaner and the brushes spin, then stop. I turn it off and when I re-start, the brushes do not spin until I push foreward. The it spins and stops again. Both belts are tight. The brushes spin if held above the carpet, but upon contact with carpet it stops. Same thing on a hard surface.

The reason for the brushes to stop when it is above any surface is there is a switch in the handle that stops the brushes so it dont burn your motor up it may have a faulty switch. ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Brushes stopped The brushes stopped turning while using the cleaner. I removed the brushes to see if the spindle was broken, it wasn't. I then removed the top plastic cover and checked the switch that engages the brushes; it didn't seem to be moving correctly. There's one spring on the switch - should there be two? Or do you think something has broken on the inside? Thanks for any help

Most likely the turbine is bad, it may just be clogged up, you can take it apart and clean it out real good. That may work, but it may not. Sometimes it is best to replace the turbine. ... Hoover F7431-900 SteamVac Vacuum

Brushes on hoover deluxe steam vac cvarpet cleaner are not rotating. Took out the brush assy and drive spins slowly but with little torque. Cannot seem to open the bottom to see if belt or direct drive..something wrong with drive mechanism for 5 brsuhes

(1) Assure the brush shut off lever on the hood is not set to the off position. \015\012(2) Is there still a square pin standing up from the one drive brush? It should be 1/4 square, and about two inches tall. That pin is the drive from the ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

Bissell proheat 2x carpet cleaner when the switch is turned on the brushes rotate fot 2 seconds then STOP ,, iIf I turn it off and on again ithe brushes will rotate for 2seconds and STOP again ?? brushes rotate for

Hey, sorry to hear you're having difficulty with the brushes. Here's a quick link to troubleshooting steps.\015\012http://www.bissell.com/FAQDetail.aspx?id ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

In my (almost new) Dyson DC31 Animal the rolling brush tends to stop like the bearing was kind of difficult to turn. I opened the side carter and removed the little belt. Without the belt the engine runs regularly. I cleaned the little knots of hairs trapped in the bearing but still the brush runs for a while then stops, tries for a bit then stops again. I even tryed putting a bit of synthetic lubricant with apparently no result. Could it be a defective bearing? Thanks for your help.

... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

My model F5906-900 --- problem is the brushes have stoped working... I pulled the brush assembly out by holding the two tabs, and all seems clean and the brush assembly rotates easly... onced the brush assembly is removed. What I did notice is the female driver slot (found in the main assembly unit) that drives the brushes seems stuck..Is that normal when the machine is not hooked up to power? How can I get the brushed going??? it is a good machine, but the brush options is important too it's ab

(1) Assure the Brush Control on the hood is NOT set to the OFF position.\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(3) Does one of the brushes ... Hoover F5906-900 Upright Steam Vacuum

The brush has stopped spinning. Suction is there brush has stopped

... Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum

Took Roomba apart to clean and now the pick up brushes start and stop during cleaning. The vaccum is clean but will not constantly spin. Runs great but pick up brushes start and stop. Is there a number for Roomba? Warranty? This one is less than one year old.

You can go to www.iRobot.com . This is the roomba website. You should be able to find replacement parts, customer support, videos or the Roomba product, and more.\015\012When y ... iRobot Roomba 530 Robotic Vacuum

I have a windsor vsp 14, it is making a bad grinding noise, when I take the top blue piece off it stops, the brush works fine and when I put the top back on it grinds really loud and gets hot. it still vacuums and the belt and brush are working fine, can't figure it out. and when the lid is on I cant see what its grinding on. It only makes a grinding noise when you pull handle back and engade to vacuum flor and stops when you put it upright.

... Windsor VS14 Versamatic Bagged Upright Vacuum

My Roomba stops within a few minutes of starting it and when I press the button, it says "Remove and Clean Roomba's Brushes." I have removed the brushes and cleaned them thoroughly, but within a few minutes, it stops again and says the same thing.

Hi,Accumulation of hair, dust and dirt in the Gearbox that prevents normal operation of the brushes. As a result, a power output is required to keep the brushes turning. As turning the brushes requires too much power, it con ... iRobot Roomba 4210 Bagless Robotic Vacuum

My power brushes on my bissel carpet cleaner stopped working. They do not rotate. This is the 2nd power cleaner I have bought and it has the same problem as the first one. What is the problem with the power brushes. After 3 uses they stop working. Bissel Proheat 2X Model #8920

You need to change the belt(s). You can find the belts for this model here. http://www.vacbelts.com/bissell-proheat-belt-combo-pack.htm ... Bissell 8910 ProHeat Clear View Upright Vacuum

H300 brushes won't stop spinning even though I switch it from "wet scrub" to "wet/dry pickup" and is leaving streaks on the floor. I have already ordered a new squeege, but that won't take care of the non-stop brush problem. Any suggestions?

I have found that the plastic piece on mine is wore out and slips when the trigger is pulled back. If you look underneath the dirty tank, you will see the black plastic pieces that over lap. I took a wiretie/zip strip and placed it around the spot ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

The brush vibrates for 30 seconds, then stops. If I depress the on/off button a couple of times it strats again, but stops after 10 seconds, and so on continously. It does it too with a new brush and with a new toothbrush.

Your battery is not getting charged properly, mabey you need to clean contacts or the life of the batterys are over ,time for new ones, if they are replaceable if not fork out for a new unit. ... Vacuums

I have cleaned & cleaned this thing! It runs for about 2 mins & stops, says "Clean Brushes"! and now it's very noticeable it's not picking up well... but is picking up a bit. I take the dust bin out, and the brushes spin.... and it has much more power.... and is very clear it is working! But it's useless without the dust bin! LOL It's only 9 months old.... called customer service, but it was the one time it worked just fine! Of course, I thought I'd stop here first before calling again! Than

Ok, this is a "Brush Height Adjustment" issue. It will probably work great on a hard surface but on carpet the brushes bog. If you've taken the unit apart already...Sorry....do it again. When you do, you'll see a String which allows the brushes to " ... iRobot Roomba 560 Robotic Vacuum

My power brushes on my bissel carpet cleaner stopped working. They do not rotate. This is the 2nd power cleaner I have bought and it has the same problem as the first one. What is the problem with the power brushes. After 3 uses they stop working. Bissel Proheat 2X Model #8920

The brushes will only work if the handle is released and the ProHeat vacuum is running . There is a micro switch inside the lower handle that switches on the DC carpet brush motor. The DC power for the motor comes from a Bridge Rectifier on the PC ... Bissell Vacuums

When i start the vacum the brushes trun for about 3-5 seconds then stops. the vacum still runs,its just the brushes stop turning, what should i do?

If your machine has no power or interrupted power, please check the following:\012 \012- Make sure the power cord is plugged into a functioning outlet to check for power.- The handle may not be installed properly, causing a ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

My Hoover spin/scrub floor cleaner has stopped scrubbing- the brushes spin for a few seconds right after turning it on, then stop until I turn it off and then on again. How can I fix this? I do not have a lot of money. I have taken off and cleaned the brushes and bottom vacuum opening.

Hi giacoma11,The common cause for this problem is the belt of your vacuum. It could be that the belt came loose or already worn out and needs replacement. To check if the belt is loose all you need to do is unscrew the bottom of the vacuu ... Hoover H3060 FloorMate SpinScrub 800 Upright Wet/Dry Vacuum

My sd40025 dirt devil ..it is not a upright. it is the follow along, bagless vacuum. has wonderful pick-up but the brush stopped spinning when i was vacumming my rug..i love this vacumm but it is only the third time i have used it. It is brand new. Why would the brush stop after maybe 20 minutes of total use?..please advise

... Dirt Devil SD40020 Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0663 seconds