Having problems with your Hoover U8188-900 Bagless Upright Vacuum ?

Brush wont spin, belt is perfect

\015 Hoover convertible upright U8188900, less than 1 yr old, brush wont spin. Carpet selection on the on/off is in proper position, belt excellant condition, has suction. Is there a way for me to fix it? Perhaps a relay or fuse. If so, how do I get to the motor and where do I find the parts.\015

Answers :

It sounds like the motor that spins the beater brush is burned out,If it is under a yr old it should be covered by the manufacturer warretee. Find a Hoover service center that does warrentee repairs.
Repair Help & Product Troubleshooting for Hoover U8188-900 Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Brush wont spin, belt is perfect

It sounds like the motor that spins the beater brush is burned out,If it is under a yr old it should be covered by the manufacturer warretee. Find a Hoover service center that does warrentee repairs. ... Hoover U8188-900 Bagless Upright Vacuum

How to repair BEAM Central Vacuum Power Brush. Motor works perfectly, belt brand new but unable to spin brush.

... Vacuums

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.

The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

Hoover steam cleaner spin scrub brushes wont turn cant find belt

I just brought mine home...assembled per instructions and tried all the troubleshooting thus far to no avail. So I popped off the brushes per instructions and took a screwdriver to the hole where the brushes axle inserts underneath the vacuum and tur ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

We have a new hoover bagless that is a couple months old. The pet hair attachment stopped working. I disassembled it found lots of hair wound around the various rollers and removed - painstakingly thorough i might add. Problem is the brush still wont spin and now the belt seems loose - I think I put it all back together correctly but wondering if there is a trick to this?

Without the model number, I can't look it up, but this has a 1 years warranty on it, maybe take it to a warranty shop. Just take proof of purchase, model and serial numbers. ... Vacuums


If the belt that drives the brush is not broken, check to see if the brush itself is stuck from turning.\015\012If is is, remove it and clean as best you can, paying special attention to the two ends. It might make sense to spray the hard rubber hol ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Brushes wont spin ,even though the belt is intact

The belt can develop a worn spot. It will be intact but not spin. Replace the belt and make and remove any hair or other garbage from around the ends of the brush bar. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The suction on my oreck is good and my belts are fine, brush is spinning, but wont pick up anything when I vacuum. Help?

Sounds like a full bag or an obstructed passage ... Oreck XL Ultra Bagged Upright Vacuum

Brush wont spin on carpet, nr. on belt YMH 29573 Where can i get speer in Sydney Australia

... Vacuums

Brushes wont spin, how do you replace belt - Bissell 9200 Upright Vacuum

Hey, sorry to hear the brushes are not turning. Here's a quick link to instructions on how to change the belt(s). We also have a terrific How-to-Video linked to this also. \015\012 ... Bissell 9200 Upright Vacuum

Brush wont spin

Was the belt worn or broken? It probably needs to be replaced. Here is the belt you need:Dyson DC07 Belt ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a

... Bissell ProHeat Deep Cleaner Upright Vacuum

I have a problem with my model 6585-3 bissell upright powerforce bagless turbo with turbo brush vacuum The brush has quit spinning upon removal i noticed that one side of the brush was free to spin the other side that has the rectangular piece to help hold into place seems to be locked up and will not spin is it corroded or have i lost a piece that joins with it that allows it to spin freely belts are good and motor is turning brush will not budge

... Vacuums

Bissell 3750 bottom brush will not spin belt is fine and lift off works great

Hey Jessica! Please contact us for assistance regarding your vacuum.Here's a quick link to assist you:\015\012http://www.bissell.com/contact-us/?cid=ccsocial ... Bissell 3750 Lift Off Bagless Upright Vacuum

My floor brush stopped spinning, I cleaned everything out as per your directions in other posts and following the instructions in the manual. Now the floor brush wobbles and has a hard time spinning when upright. Looking at the end of the brush, opposite the drive belt, the bearing-type end that the brush spins on appears to be off-centered. Is there an easy way to fix this???

... Bissell 3130 Bagless Upright Vacuum

I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn

Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum

I have a Bissell Pro Heat 2X carpet cleaner and the brushes spin, then stop. I turn it off and when I re-start, the brushes do not spin until I push foreward. The it spins and stops again. Both belts are tight. The brushes spin if held above the carpet, but upon contact with carpet it stops. Same thing on a hard surface.

The reason for the brushes to stop when it is above any surface is there is a switch in the handle that stops the brushes so it dont burn your motor up it may have a faulty switch. ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag

... Euro-Pro EP621 Bagless Upright Vacuum

Miele White Star SEB 204, powerhead stopped spinning. brushes are clear of debris, belt (#3854940) is not broken. Could belt be stretched so that brush head does not spin?

Yes, most likely the belt has stretch. Flat belts do this after a short time and need to be replaced when problems start with the brush roll not wanting to turn. Also check the brush roll, make sure that the ends turn freely, if not, then replace i ... Miele Vacuums

Agitator brush wont spin once vacuum is placed on floor

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=618889&thid=573865\015\012Agitator brush wont spin once vacuum is placed on...\015\012Posted by coral7980 on May 05, 2008\015\01 ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Why wont the brushes spin? I have had this machine for about 3 years and it has always worked great, tonight the brushes will not spin at all, it still sprays and sucks up the water. We took the brushes off and were able to spin them by hand

In this machine there is no belt. The brushes actually spin by vacuum and in the turbine assembly there is a small wheel bearign which rusts out. You will need to remove and repair or replace the turbine and gear assembly P/N should be 43191009 ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

No suction power ,brush wont spin on carpet power nozzle. When it

You need to replace the belt that turns the brush. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

I have a Eureka 5902AVZ and the brushroll does not work. when i remove the belt, which is not torn nor worn out, the motor spins perfectly fine. Though when i put the brushroll back into place, it shows that the motor is trying to spin, but with resistance. it seems the brushroll will not spin if locked into place, because there is no attachment on the left side of the brushroll that will allow it to spin freely with the belt. am I missing some parts or is there something else wrong?

Hi and welcome to Fixya. I am Kelly. \015\012\015\012You have correctly identified the problem as the brush roll itself. \015\012\015\012There is a bearing under each end cap of the brush roll. You can gain access to the ... Eureka 5902AVZ Bagless Upright Vacuum

I put both belts on my U6634-900 and i can make brush spin manually, but the small belt looks to big, not fitting snugly and not turning brushes when i give it juice. Yes I have the right belts.

... Hoover U6634-900 WindTunnel Bagless Upright Vacuum

On our Hoover U6445-900 (Mach 6.9) we replaced the small belt that goes to beater brushes in front of unit. Upon starting, the Hoover quickly got hot and smoky. We shut it off and looked things over carefully, but the second try also resulted in friction heat on the belt. Now it appears the belt may have stretched due to heat and the brushes won't spin. Any ideas?

Are you sure you purchased the right size belt..the friction you speak of is usually caused by a belt not being the right tightness or a jammed beater brush ... Hoover U6446-900 WindTunnel Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0610 seconds